Alcatel-Lucent OmniAccess 5510 ADSL User manual

Beta
1
2
Notes on numbered items on banner & legal pages
1u26801 West Agoura Road
Calabasas, CA 91301
[phone]
FAX [phone]
[email protected]
US Customer Support—[phone]
International Customer Support—[phone]
Internet—service.esd.alcatel-lucent.com
Website: www.alcatel-lucent.com
Part No: 060269-00, Rev. C
For final production, import color definitions from
\\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm.
Do not import other template elements such as page layout.
To return to the draft version, import color def’ns from draft-colors.fm.
To switch to the beta version, import color def’ns from beta-colors.fm
OmniAccess 5510
Unified Services Gateway
Getting Started Guide
Release 2.2-R03, 2.2-R04, 2.3.2

CAUTION: THIS EQUIPMENT IS TO BE INSTALLED AND SERVICED ONLY BY QUALIFIED SERVICE
PERSONNEL.
Batteries Caution. There is a danger of explosion if the battery in your chassis is incorrectly replaced.
Replace the battery only with the same or equivalent type of battery recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions. The
manufacturer’s instructions are as follows:
Copyright
The Specifications and Information regarding the products in this manual are subject to change without
notice. All statements, information, and recommendations in this manual are believed to be accurate
but are presented without warranty of any kind, express or implied. Users must take full responsibility
for their application of any products.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET
FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED
HEREIN BY THIS REFERENCE.
This equipment has been tested and found to comply within the limits pursuant to the (Centre for
Telecom) rules. These limits are designed to provide protection against harmful interference when the
equipment is operated in a commercial environment.
The following information is for the Users of the OmniAccess 5510 Unified Services Gateway: If it is not
installed in accordance with the installation instructions, it may not function exactly to the said
specifications. Modifying the equipment without Alcatel-Lucent's written authorization may result in the
equipment no longer complying with the said dimensions.
Copyright © 2009, Alcatel-Lucent. All rights reserved.
Not withstanding any other warranty herein, all hardware and software are provided "as is" with all
faults. Alcatel-Lucent disclaim all warranties, expressed or implied, including, without limitation, those
of merchantability, fitness for a particular purpose and non-infringement or arising from a course of
dealing, usage, or trade practice. In no event shall Alcatel-Lucent be liable for any indirect, special,
consequential, or incidental damages, including, without limitation, lost profits or loss or damage to data
arising out of the use or inability to use this manual, even if Alcatel-Lucent have been advised of the
possibility of such damages.
Return the module with the battery to Alcatel-Lucent. The battery will be replaced at Alcatel-
Lucent’s factory.
3
4
5

Table of Contents
Package Contents.....................................................................................................................1
Required Tools and Equipment..........................................................................................2
Connecting AC Input Power......................................................................................................3
Connecting to the OmniAccess 5510 USG Console Port.........................................................4
Starting the OmniAccess 5510 USG.........................................................................................6
Performing Basic Configuration Tasks......................................................................................9
Accessing the OmniAccess 5510 USG Through CLI .........................................................9
Accessing the OmniAccess 5510 USG Through GUI ......................................................15
Obtaining Technical Support...................................................................................................15

List of Figures
Connecting the Power Brick on OmniAccess 5510 USG 3
Connecting to the OmniAccess 5510 USG Console 4

List of Tables
Console Properties 5
OmniAccess 5510 USG System LED Status 6

OmniAccess 5510 USG Overview
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
1
Alcatel-Lucent
Beta Beta
OmniAccess 5510 Unified Services Gateway Getting Started Guide
OmniAccess 5510 USG Overview
The OmniAccess 5510 USG is designed to provide most commonly used network
services, such as routing, switching, wide area network (WAN) connectivity,
network security with firewall, and related services using a non-modular platform
providing ethernet switching and a single WAN interface.
PACKAGE CONTENTS
1. The OmniAccess 5510 USG
• 1U fixed chassis
• AC power supply
• AC country specific power cord
• DB9->RJ45 console connector
• 256 MB compact flash
• Product documentation card
2. Optional Rack Mount Equipment
• Power supply tray
• Power supply tray brackets and screws
• 19-inch rack mount ears and screws
3. Optional DC Power Supply and Power Supply Tray
• DC Power Supply
• Power supply tray
• Power supply tray brackets and screws

Package Contents
Left running head:
Chapter name (automatic)
2Beta Beta
OmniAccess 5510 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
REQUIRED TOOLS AND EQUIPMENT
You need the following items to install the OmniAccess 5510 USG:
•Electrostatic Discharge Wrist Strap (ESD)
•Level (optional)
•Tape Measure (optional)
Note: This equipment is designed to the highest quality standards of materials,
workmanship, and safety. Do not bypass any of the safety features of this equipment
or operate this in an improper environment.
Warning: Only trained and qualified personnel should be allowed to install or replace the
OmniAccess 5510 USG. Refer to the warnings and safety notes that are given in the
“OmniAccess 5510 Unified Services Gateway Hardware Users Guide” provided
with this device.
Refer to the “Rack Mounting the OmniAccess 5510 USG” section in the
“OmniAccess 5510 Hardware Users Guide” to install the OmniAccess 5510 USG
in the rack.

Connecting AC Input Power
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
3
Alcatel-Lucent
Beta Beta
OmniAccess 5510 Unified Services Gateway Getting Started Guide
CONNECTING AC INPUT POWER
This section provides the procedures for connecting AC-input power to the
OmniAccess 5510 USG.
Note: The OmniAccess 5510 USG installation must comply with all the applicable codes. All
the hardware materials used should be of compatible material and preclude
loosening, deterioration, and electro-chemical corrosion of hardware and joined
material.
Note: For more details on power supply specifications, see the “AC Power Specifications”
chapter in the “OmniAccess 5510 Unified Services Gateway Hardware Users
Guide”.
Figure 1: Connecting the Power Brick on OmniAccess 5510 USG
Step 1: Plug the country specific power cord into the AC power supply.
Step 2: Plug the power cord into the AC power source.
Step 3: Be sure that the power cable is not left in a hazardous position that may
restrict movement of personnel or that may fray due to movement of other
equipment near the system.
Step 4: Connect the Kycon connector from the power supply to the chassis.
Step 5: Secure the Kycon connector to the chassis by tightening the power
connector’s retaining bracket captive thumb screw as shown in figure.

Connecting to the OmniAccess 5510 USG Console Port
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
4
Alcatel-Lucent
Beta Beta
OmniAccess 5510 Unified Services Gateway Getting Started Guide
CONNECTING TO THE OMNIACCESS 5510 USG CONSOLE PORT
The OmniAccess 5510 USG has a RJ-45 console port connector. A DB-9 to RJ-
45 (female) adapter is provided with the system to access the console port via a
DTE (computer/terminal) using a straight-through Ethernet cable. For additional
connector details, refer to “Pin Connector Details for OmniAccess 5510 USG”
in the “OmniAccess 5510 Unified Services Gateway Hardware Users Guide”.
Figure 2: Connecting to the OmniAccess 5510 USG Console
To connect the OmniAccess 5510 USG to the console, perform the following
steps:
Step 1: Connect the RJ-45 end of the console cable to the rear panel console port
on the OmniAccess 5510 USG and the DB-9 end to the serial port (COM) on your
computer/terminal.
Step 2: Start your terminal emulation software.
Example: kermit or hyperterm terminal (if you are using Microsoft Windows
operating system) or minicom terminal (if you are using Unix/Linux operating
system).
RS-232 Console Port
with RJ-45 Connector

Connecting to the OmniAccess 5510 USG Console Port
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
5
Alcatel-Lucent
Beta Beta
OmniAccess 5510 Unified Services Gateway Getting Started Guide
Step 3: Set the console session as follows:
Table 1: Console Properties
Step 4: Watch for console message output or press the Enter key to get the
device prompt.
Parameter Value
Baud rate 9600
Parity None
Data Bits 8
Stop Bit 1
Flow control None