Aleko AWRCLED Series User manual

433MHz & 868MHz & 315MHz
DC3V/23A & 3V/CR2430
Specific parameters to the nameplate shall prevail
(AWRCLED)
DC3V/CR2430
AWRCLED series：AWRCLED
Setting Up Manual
Pair Additional Remote
Remove All Remotes
The setting steps are different for left facing mounted motor and right facing mounted motor.
Carefully check which side you have mounted the motor and follow the correct setting steps.
One motor can be paired to 20 remotes/sensors in total, follow below steps to add a new remote
P2 P2
→ →
P2(a) P2(a)
P2
P2(b)
Press P2 (1 beep and 1 jog) and P2 (1 beep and
1 jog) on existing emitter, press P2 on new emitter
to add (beeps multiple and 1 jog), new emitter is
paired to the motor.
→ → Press P2 (1 beep and 1 jog), STOP (1 beep and
1 jog), and P2 (beeps multiple and 1 jog), all
emitters are deleted.
P2
P2
P2
P2
STOP
Specification
8307 S 192nd St Kent, WA 98032
Phone: [phone] or 253-246-8222
[e-mail]
www.Aleko.com
AWRCLED Back
Setting button P2
Up button
Stop button
Down button
AWRCLED Series Control System
AWRCLED
LED control
button
LED Control：Press LED control button once,it will turn on the LED to 50% brightness. Press the button
again will turn the LED to 100% brightness.Press the button once again,it will turn off the LED.

Left Facing Mounted Motor Right Facing Mounted Motor
Pair AWRCLED with DM45RD Pair AWRCLED with DM45RD
1.Disconnect the power,wait for 10s, reconnect the power,the awning will jog once,beep once.
2.Press P2 on the remote once,the awning will beep once.
3.Press P2 on the remote once again,the motor will beep again.
4.Turn the remote immediately and press UP button on the remote, the awning will jog once and beep
several times. The remote is paired with the motor.
5.Press Up button on the remote, the awning shall be retracted.
Troubleshooting tips: If you did not hear the awning beeps or jogs, it is probably because the awning did not
“hear” it, you may repeat the step to make sure the awning feedbacks.
Motor Head View on Right-mount
Red
White
6. Press DOWN
button on the
remote
Set Deploy Position
6.1 If the awning
automatically stops before
demanded position.
Turn the red worm towards "+",you
will move the awning directly to the
demanded position.
-
+
-
+
-
+
-
+
6.2 If awning did not stop,
it means the motor travel
is too long,need to make
it shorter.
Turn the red worm towards "-", keep
checking if the awning can stop at the
demanded position to see if the travel
is shortened enough.
If the travel is over-shorted,turn the
red worm towards "+".
Set Retract Position（It is suggested to be set 2cm away from the tube）
7. Press UP
button on
the remote Turn the white worm towards "-",
keep checking if the awning can stop
2cm from the tube,to see if the travel
is shortened enough.
If the travel is over-shorted,turn the
white worm towards "+".
7.1 If the awning
automatically stops before
awning closes
7.2 If awning did not stop,
it means the motor travel
is too long,need to make
it shorter.
Turn the white worm towards "+",you
will move the awning bottom bar 2cm
away from the tube.
6. Press DOWN
button on the
remote
Set Deploy Position
6.1 If the awning
automatically stops before
demanded position.
-
+
-
+
-
+
6.2 If awning did not stop,
it means the motor travel
is too long,need to make
it shorter.
Set Retract Position（It is suggested to be set 2cm away from the tube）
7. Press UP
button on
the remote
7.1 If the awning
automatically stops before
awning closes
7.2 If awning did not stop,
it means the motor travel
is too long,need to make
it shorter.
Turn the white worm towards "+",you
will move the awning directly to the
demanded position
Turn the white worm towards "-",
keep checking if the awning can stop
at the demanded position to see if the
travel is shortened enough.
If the travel is over-shorted,turn the
white worm towards "+".
-
+
Turn the red worm towards "+",you
will move the awning bottom bar 2cm
away from the tube.
Turn the red worm towards "-",
keep checking if the awning can stop
2cm from the tube,to see if the travel
is shortened enough.
If the travel is over-shorted,turn the
red worm towards "+".
Motor Head View on left-mount
Red
White
1.Disconnect the power,wait for 10s, reconnect the power,the awning will jog once,beep once.
2.Press P2 on the remote once,the awning will beep once.
3.Press P2 on the remote once again,the motor will beep again.
4.Turn the remote immediately and press DOWN button on the remote, the awning will jog once and beep
several times.The remote is paired with the motor.
5.Press Up button on the remote, the awning shall be retracted.
Trouble shooting tips：If you did not hear the awning beeps or jogs, it is probably because the awning did not
“hear” it, you may repeat the step to make sure the awning feedbacks.
Attention: The interval between the steps in step 1 to 4 shall not be longer than 6s, otherwise the motor will
exit the setting mode.
Attention: The interval between the steps in step 1 to 4 shall not be longer than 6s, otherwise the motor will
exit the setting mode.