Stirling SFTF36B-LED User manual

Model Number SFTF36B-LED
90cm Tower Fan
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]

Welcome
Congratulations on choosing to buy a Stirling product.
All products brought to you by Stirling are manufactured to the highest standards
of performance and safety and, as part of our philosophy of customer service and
satisfaction, are backed by our comprehensive 1 Year Warranty. We hope you will
enjoy using your purchase for many years to come.
2
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]

Contents
02 Welcome
04 Warranty Details
05 General Safety Instructions
07 Product Overview
09 Getting Started
10 Instructions
11 Troubleshooting
12 Cleaning and Storage
12 Disposal Instructions
12 Technical Specifications
13 Simulated Wind / Sleep Modes
14 Repair and Refurbished Goods or Parts Notice
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
[email protected] 3
AFTER SALES SUPPORT
1300 366 155
AUS

YEAR WARRANTY
1
90cm Tower Fan
Warranty Details
The product is guaranteed to be free from defects in workmanship and parts for a
period of 12 months from the date of purchase. Defects that occur within this
warranty period, under normal use and care, will be repaired, replaced or refunded at
our discretion, solely at our option with no charge for parts and labour. The benefits
conferred by this warranty are in addition to all rights and remedies in respect of the
product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
4
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]

IMPORTANT: Read these instructions fully before using the fan. Retain these
instructions for future reference.
Use this fan only as described in this manual. Other use that is not
recommended may cause fire, electric shock or injury to persons.
This product is intended for household use ONLY and not for commercial,
industrial or outdoor use.
To reduce the risk of fire or electric shock, do not use this fan with any
solid-state speed control device.
This appliance is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
Turn the fan OFF and unplug the fan from the outlet when not in use,
when moving the fan from one location to another and before cleaning.
To disconnect the fan, first turn the unit OFF, grip the plug and pull it from
the wall outlet. Never pull the plug by the cord.
Do not operate the fan in the presence of explosive and/or flammable
fumes.
Avoid contact with moving fan parts.
The use of attachments not recommended by the manufacturer may be
hazardous.
Place the fan on a dry level surface.
Do not hang or mount fan on a wall or ceiling.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
General Safety Instructions
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
[email protected] 5
AFTER SALES SUPPORT
1300 366 155
AUS
To protect against electric shock: do not place fan on window
sills, immerse unit plug cord in water, or spray with liquids.
Do not place the fan or any parts near an open flame, cooking
or other heating appliance.
Do not operate fan with a damaged cord or plug, or if the
product malfunctions, or is dropped and damaged in any
manner.

13.
14.
15.
16.
Do not operate if the fan housing is damaged.
A loose fit between the AC outlet (receptacle) and plug may cause
overheating and a distortion of the plug. Contact a qualified electrician
to replace loose or worn outlet.
Only use on a power supply that matches that shown on the unit’s
rating label.
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid hazard.
6
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]
WARNING: Keep batteries out of reach of children.
Swallowing may lead to serious injury or death in as
little as 2 hours due to internal burns. If swallowed,
go straight to a hospital emergency room. Dispose
of used batteries immediately.

Product Overview
Control Panel1.
2.
3.
4.
5.
6.
LED Display
Air Outlet
Rear Vent
Base
Carry Handle
Remote Control (see page 8)1.
2. Screws (x3) for base assembly
[includes 3V cell (CR2032)]
1
2
3
4
5
6
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
[email protected] 7
AFTER SALES SUPPORT
1300 366 155
AUS
Not Shown

Product Overview
LED Display
Remote Control Control Panel
1.
2.
3.
4.
5.
6.
7.
Fan Speed ‘Simulated Wind’ Mode
Sleep Mode
Oscillation Indicator
Normal Fan Mode
AUTO Mode
Room Temperature
/ Timer Display
See ‘Instructions’ on page 10 for details
1
2
3
4
5
6
7
8
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]

Getting Started
Do not use this fan unless the base is properly attached as
shown below
Keeping the power cord in the
central gap between the 2
halves of the unassembled
Base, connect the 2 halves by
pushing the plastic pegs on one
half into the corresponding slots
on the other half.
Using the 3 provided thumb-
screws, secure the assembled
Base (from step 1) to the bottom
of the main Tower Fan unit.
1.
2.
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
[email protected] 9
AFTER SALES SUPPORT
1300 366 155
AUS

Instructions
Once the base has been assembled properly, plug the power plug into a mains source that
matches the specifications on the fan’s rating label.
When the LED Display shows the detected Room Temperature, the fan is ready for operation. You
can operate the unit via either the unit’s Control Panel or the Remote Control.
TIMER Button: When the fan is in use, you can set the Timer to turn off the fan after
the specified time. Press this button repeatedly to increase the Timer setting in
0.5-hour increments (up to a maximum of 8 hours) as indicated on the LED Display.
After 5 seconds, the Timer starts. Once the Timer has run out, the fan will turn off, and
the detected Room Temperature is shown on the LED Display.
OSCILLATION Button: Press to start/stop Fan Oscillation.
AUTO Button: Press this button to enable/disable Auto Mode.
When enabled, Auto Mode automatically turns on the fan when the room temperature
is detected to be above 25°C; it also turns off the fan when the temperature is
detected to be below 25°C. The Fan Speed will be automatically adjusted, according
to the temperature.
MODE Button: Press to select Normal Mode, Natural Breeze Mode or Sleep Mode (as
indicated on the LED Display).
SPEED Button: Press to select Fan Speed: Low / Medium / High
ON/OFF Button: Press this button to start the fan at Low Speed, in Normal Mode.
Press again to turn the fan off.
AUTO
NORMAL Mode: Fan operates at the speed selected with the Speed Dial.
SIMULATED WIND Mode: Fan speed varies automatically to simulate a breeze*.
SLEEP Mode: Fan speed varies automatically for use during sleep*.
*See ‘SIMULATED WIND / SLEEP MODES’ for fan speed patterns
10
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]

Troubleshooting
The fan doesn’t work properly.
AUTO mode doesn’t work.
-
-
-
-
Make sure the power plug is inserted securely into a mains outlet, and that the outlet is active.
If the unit is in AUTO mode, the fan will only work when the room temperature is detected to
be above 25°C. Press the ‘AUTO’ button once to enable/disable AUTO mode.
Check if the Timer function has been activated. Press the ON/OFF button once more.
Is the Fan in NORMAL mode? ‘SIMULATED WIND’ and ‘SLEEP’ modes may incorporate some
periods of fan inactivity (See ‘SIMULATED WIND / SLEEP MODES’ for fan speed patterns
-AUTO Mode only activates the fan when the detected temperature is above 25°C. Check
that there are no draughts or other sources of cooling (or heating) that may affect the fan’s
temperature detection.
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
[email protected] 11
AFTER SALES SUPPORT
1300 366 155
AUS

Cleaning and Storage
Technical Specifications
•
•
•
•
•
•
•
Unplug the fan before cleaning.
Use only a soft, damp cloth to gently wipe the outer surfaces of the fan clean.
To clean between the grilles, we recommend using a pipe cleaner, flexible dust wand, vacuum
cleaner or compressed air to gently remove the dust.
DO NOT immerse the fan in water and never allow water to drip into the motor housing.
DO NOT use gasoline, paint thinner or other chemicals to clean the fan.
For storage, you may leave the fan assembled and covered to protect it from dust. Store the fan in
a cool, dry place.
The rear vent can be cleaned of dust with a soft, dry brush. For a thorough clean, the rear vent can
be detached. It is attached with 6 screws, which can be removed as shown below. Be sure to
re-attach the rear panel to the main unit with the 6 screws before plugging the power cord back in.
Power Requirements: AC 220-240V, 50Hz
Power Consumption: 60W
Disposal Instructions
When the appliance has reached the end of its life, please contact your local council for
environmentally-friendly disposal options.
12
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]

Simulated Wind / Sleep Modes
13
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
AFTER SALES SUPPORT
1300 366 155
AUS [email protected]

90cm Tower Fan
YEAR WARRANTY
1
Unfortunately, from time to time, faulty products are manufactured which need to be
returned to the Supplier for repair.
Please be aware that if your product is capable of retaining user-generated data (such as
files stored on a computer hard drive, telephone numbers stored on a mobile telephone,
songs stored on a portable media player, games saved on a games console or files stored
on a USB memory stick) during the process of repair, some or all of your stored data may
be lost.
We recommend you save this data elsewhere prior to sending the product for repair.
You should also be aware that rather than repairing goods, we may replace them with
refurbished goods of the same type or use refurbished parts in the repair process.
Please be assured though, refurbished parts or replacements are only used where
they meet ALDI’s stringent quality specifications.
If at any time you feel your repair is being handled unsatisfactorily, you may escalate your
complaint. Please telephone us on 1300 366 155 or write to us at:
YALE PRIMA PTY LTD
Unit 1, 192 Kingsgrove Road,
Kingsgrove, NSW 2208
STIRLING®Help Desk 1300 366 155
(Operating Hours: Mon-Fri 08:30AM to 06:00PM AEST)
email: [email protected]
Repair and Refurbished
Goods or Parts Notice
MODEL: SFTF36B-LED PRODUCT CODE: 44017 12/2014
[email protected] 14
AFTER SALES SUPPORT
1300 366 155
AUS