All In 1 Gaming Pro Sim Frame User manual

Your pit crew is here to support you.
allin1gaming.com/support allin1gaming.com
Skype Us
[email protected]
Assembly Instructions
Pro Sim Frame
chat with a live agent
allin1gaming
email our team
support page

01 BASE ASSEMBLY
Page 2
ST-EXT-001-0405 ST-HP-003-0001
ST-EXT-005-1305
ST-EXT-002-0675 HW-FN-003-0018 HW-FN-002-0001
2 x 2 x 1 x 6 x 12 x 12 x
Repeat the process for the positions below

02 SIM FEET ASSEMBLY
Page 3
HW-FN-003-0020 HW-FN-002-0001
4 x 4 x 28 x 28 x
HW-LF-008-0001 MT-BP-001
Repeat the process for the positions below
4 x
HW-FN-008-0002

03 UPRIGHT ASSEMBLY
ST-HP-003-0001 ST-HP-003-0004 HW-FN-003-0018
Page 4
ST-EXT-002-0720 HW-FN-002-0001
24 x
2x 24x
2x
4x

Page 5
ST-HP-003-0001 ST-EXT-002-0585
ST-EXT-001-0360 HW-FN-002-0001
8 x
1 x
1 x 8 x 4 x
04 SIDE MOUNT ASSEMBLY
HW-FN-003-0018

04a SIDE MOUNT ASSEMBLY
Page 6
ST-GP-003-0001 HW-FN-003-0018 ST-EXT-001-0180
2 x
4 x
4 x
DELUXE SIDE MOUNT
HW-FN-002-0001
4 x
FANATEC SIDE MOUNT DELUXE SIDE MOUNT
ST-HP-003-0001 HW-FN-003-0018
8 x
4 x
HW-FN-002-0001
8 x
Repeat step 1 for the remaining 4 brackets. Add 4 t-
nuts into the slots of the 180mm profiles to match
with the hole locations of your shifter (or other).
FANATEC SIDE MOUNT
WITH SHIFTER PLATE
2 x 2 x

05 FRONT WHEEL MOUNT ASSEMBLY
Page 7 front
1 x 1 x 8 x
MT-WH-001 MT-FW-001 HW-FN-008-0003 HW-FN-015-0025
HW-FN-015-0030
4 x 4 x
25mm
30mm
30mm
25mm
MT-WH-002
1 x
ST-GP-003-0001
4 x

Page 7 deck
HW-FN-015-0025
8 x
HW-FN-008-0003
8 x
HW-FN-001 HW-FN-002
HW-WD-001
1 x 1 x 1 x
05 WHEEL DECK MOUNT ASSEMBLY
ST-GP-003-0001
4 x

05 FANATEC PODIUM MOUNT ASSEMBLY
1 x
MT-WH-001 HW-FN-015-0025
8 x
MT-WH-002
1 x
Page 7 Fanatec
1 x 1 x
MT-PD-001MT-PD-002 ST-EXT-002-0187
2 x 4 x
HW-FN-003-0020
do step 3 after 1 /2 om the following page

05a ATTACH WHEEL MOUNT TO UPRIGHTS
Page 8
HW-FN-003-0020
8 x
HW-FN-002-0001
8 x

06 SEAT MOUNT ASSEMBLY
ST-EXT-001-0495
Page 9
HW-FN-003-0018
12 x
HW-FN-002-0001
12 x
ST-GP-003-0001
4 x
2 x
ST-HP-003-0001
4 x
ST-GP-003-0001
ST-HP-003-0001
Optional -With Undermount Seating Kit

Page 10
HW-FN-003-0020
2 x
HW-FN-002-0001
14 x
07a PEDAL MOUNT ASSEMBLY - USING THE PIVOT METHOD
Place one T-nut in the center top
slot with 1 on each side 12
inches from the center T-nut
Align the center T-nut with the
center hole of the the pedal
mount and tighten with a screw
Slide in the remaining T-nuts
so that they align with the
red circles as indicated in the
photo.
**Repeat the same steps for
the opposite side.
2 x
MT-PP-001
The pedal plates can be mounted either freestyle (step 7c) or using the center hole as a pivot if
you want to easily rotate your pedal angle.

For pedals with a through hole capable
of mounting from above
For pedals that mount upwards, use
the provided 4 x corner brackets
Align the 2 spreader bars into the
slots as in the photo. Secure a
flathead screw into center hole of
each profile. Leave the 45x45 profile
slightly loose as it might need to be
adjusted to fit your pedal set.
07b ADD PEDAL MOUNT HARDWARE
Page 11
HW-FN-003-0018
4 x
HW-FN-002-0001
4 x
ST-GP-003-0001
4 x
ST-EXT-001-0385
1 x
ST-EXT-002-0385
1 x
HW-FN-015-0025
6 x
OPTIONAL WITH PURCHASE OF MOUNTING KIT

Page 12
HW-FN-003-0020
12 x
07c PEDAL MOUNT ASSEMBLY
Place your pedals set onto the pedal
mount. Adjust the 45x45 profile by
sliding it forward/backward so that all
mounting postions are aligned.
Once aligned, remove pedal set and
tighten 45x45 profile.
Center screw acts as a pivot.
Keep in place when rotating and adjust
positions of the other screws.
1 outside hole rotation results in 5
possible mounting screws.
2 outer hole rotation results in 7
possible mounting screws
Please note that only 3 screws are
needed for the pedal plate to be secure
in the cockpit.

To mount your pedals using any hole combination, angle, and height that you
choose, follow the same steps above changing only the t-nut layout from step
#4 from page 12 and screw positions from steps 2 & 3 from page 14.
07c PEDAL MOUNT - FREESTYLE METHOD
Examples of custom freestyle mounting options.
Page 13