Alliance Laundry Systems FLW700C User manual

Installation
www.comlaundry.com
Tumble Action
Washers
FLW700C
NOTA: El manual en
españolaparecedespués
del manual en inglés.
Part No. 800971
July 2001
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

© Copyright 2001, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
800971 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Table of
Contents
Replacement Parts.............................................................................. 3
Installation........................................................................................... 5
Dimensions and Specifications............................................................. 5
Before You Start................................................................................... 6
Tools ................................................................................................ 6
Electrical .......................................................................................... 6
Water................................................................................................ 6
Accessories Bag............................................................................... 6
Installing the Unit ................................................................................. 7
Step 1: Position Washer Near Installation Area .............................. 7
Step 2: Connect Water Inlet Hoses .................................................. 7
Step 3: Connect Drain Hose to Drain Receptacle............................ 8
Step 4: Position and Level the Washer ............................................ 10
Step 5: Remove the Shock Sleeves and Shipping Brace ................. 11
Step 6: Wipe Out Inside of Washer Drum....................................... 11
Step 7: Plug In the Washer............................................................... 11
Step 8: Check Installation ................................................................ 12
Moving Unit to a New Location ...................................................... 12
Electrical Requirements........................................................................ 12
Grounding Instructions .................................................................... 13
Water Supply Requirements................................................................. 14
Water Temperature .......................................................................... 14
Water Pressure ................................................................................. 14
Risers................................................................................................ 14
Information for Handy Reference......................................................... 15
Installer Checklist................................................................. Back Cover

2800971
© Copyright, Alliance Laundry Systems LLC –DO NOT COPY or TRANSMIT
Notes

3
800971 © Copyright, Alliance Laundry Systems LLC –DO NOT COPY or TRANSMIT
Replacement Parts
If replacement parts are required, contact the source
from where you purchased your washer, or contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
Phone: [phone]
for the name and address of the nearest authorized
parts distributor.

800971
4© Copyright, Alliance Laundry Systems LLC –DO NOT COPY or TRANSMIT
Notes

5
800971 © Copyright, Alliance Laundry Systems LLC –DO NOT COPY or TRANSMIT
Installation
Dimensions and Specifications
FLW701N
FLW701N
28"
(71.1 cm)
2" (5.1 cm)
17.5"
(44.8 cm)
41.2" (104.6 cm)
14.9"
(37.9 cm)
29.6" (75.1 cm)
31.1" (79 cm)
26.9"
(68.3 cm)

Installation
800971
6© Copyright, Alliance Laundry Systems LLC –DO NOT COPY or TRANSMIT
Before You Start
Tools
For most installations, the basic tools you will need
are:
Figure 1
Electrical
Refer to serial plate for specific electrical
requirements. For more detailed information refer to
section on Electrical Requirements.
Water
Washer needs two standard 3/4 in. (19.1 mm) water
supply faucets with a pressure between 138 and
827 kPa (20 to 120 pounds per square inch). For more
detailed information refer to section on Water Supply
Requirements.
Accessories Bag
An accessories bag has been shipped inside your
washer. It includes:
●Two inlet hoses with washers. Refer to step 2 of
Installation.
●Four rubber feet. Refer to step 4 of Installation.
●Beaded tie-down strap. Refer to step 3 of
Installation.
●Installation instructions.
●Use and Care Guide.
●Operating insert.
●Warranty bond.
●Helpful Hints insert.
●Bag for storing shipping materials.
D820I
1Wrench
2Screwdriver
3Pliers
4Socket Wrench
5Level
1234
5

Installation
7
800971 © Copyright, Alliance Laundry Systems LLC –DO NOT COPY or TRANSMIT
Installing the Unit
Step 1: Position Washer Near Installation
Area
IMPORTANT: Install dryer before washer. This
allows room for attaching exhaust duct.
Move washer as close to the desired area of
installation as possible.
Figure 2
Step 2: Connect Water Inlet Hoses
NOTE: Refer to section on Water Supply
Requirements before connecting water inlet hoses.
Remove the four plain rubber washers from
accessories bag, and install them according to
Figure 3.
Turn on the water supply faucets and flush the lines for
approximately two minutes to remove any foreign
materials that could clog the screens in the water
mixing valve.
NOTE: When installing in newly constructed or
renovated building, it is very important to flush the
lines since build-up may have occurred during
construction.
IMPORTANT: Thread hose couplings onto valve
connections finger-tight, then approximately
1/4 turn with pliers. DO NOT cross thread or
overtighten couplings.
Turn water on and check for leaks. If leaks are found,
retighten the hose couplings. Continue tightening and
rechecking until no leaks are found.
Figure 3
Figure 4
FLW702N
FLW702N
H091I
1Rubber Washer (Plain)
2Inlet Hose
FLW723N
1Water Supply Faucets
2Cold Water Connection
3Hot Water Connection
4Water Inlet Hoses
H091I
1
2
FLW723N
123
WATER
MIXING
VALVE
4

Installation
800971
8© Copyright, Alliance Laundry Systems LLC –DO NOT COPY or TRANSMIT
Step 3: Connect Drain Hose to Drain
Receptacle
Remove the drain hose from its shipping position on
the rear of the washer by unhooking the hose from the
retainer clamp.
Find the instructions, on the following pages, that are
appropriate for your type of drain receptacle
(standpipe, sink, wall, or laundry tub). Follow these
instructions to properly install the drain hose.
IMPORTANT: Drain receptacle must be capable of
handling a minimum of 1-1/4 inch (3.2 cm) outside
diameter drain hose.
Figure 5
Standpipe Installation
Place the drain hose into the standpipe.
Remove the beaded tie-down strap from accessories
bag and place around standpipe and drain hose and
tighten strap to hold hose to standpipe. This will
prevent the drain hose from dislodging from drain
receptacle during use.
Figure 6
Sink Installation
For this type of installation, use the beaded tie-down
strap (supplied in accessories bag) or use a large wire
tie (available from your local hardware store), and
secure the drain hose to the cabinet top hinge (refer to
Figure 7). This will prevent the drain hose from
dislodging during use.
Figure 7
FLW703N
1Retainer Clamp
1
FLW704N
124" to 36" (91.44 cm recommended height)
2Standpipe 2" (5.08 cm) or 1-1/2" (4 cm)
3Beaded Tie-Down Strap
FLW705N
1Drain Hose
2Tie-Down Strap (Wire tie or tape if
necessary)
FLW704N
1
23
FLW705N
1
2