Alliance Laundry Systems HY125_MICRO Owner's manual

Installation/Operation/Maintenance
www.alliancelaundry.com
Washer-Extractors
Cabinet Freestanding
Refer to Page 8 for Model Identification
Part No. D1590ENR2
December 2014
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
© Copyright 2014, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
1
D1590ENR2
Table of
Contents
Safety Information.............................................................................. 4
Explanation of Safety Messages........................................................... 4
Important Safety Instructions ............................................................... 4
Safety Decals ................................................................................... 7
Important Information Before Installation............................................ 7
Transportation and Storage .............................................................. 7
For Installation ................................................................................. 7
Machine Information ....................................................................... 7
Introduction......................................................................................... 8
Model Identification ............................................................................. 8
Replacement Parts ................................................................................ 9
Customer Service.................................................................................. 9
Technical Specifications ..................................................................... 10
75/335, 90/400 and 125/520 Models Without Tilt Option ................... 13
180/800, 230/1000 and 275/1200 Models Without Tilt Option ........... 15
180/800 Models With Tilt Option ........................................................ 17
230/1000 Models With Tilt Option ...................................................... 19
275/1200 Models With Tilt Option ...................................................... 21
Installation........................................................................................... 23
Handling, Transport and Storage.......................................................... 23
Transport and Storage ...................................................................... 23
Handling During Installation ........................................................... 23
Unpacking ........................................................................................ 23
Space Requirements.............................................................................. 23
Required Machine Working Conditions .......................................... 23
Size of a Laundry Room .................................................................. 23
Machine Positioning ............................................................................. 24
Machine Anchoring .............................................................................. 24
75/335, 90/400 and 125/520 Models .................................................... 25
180/800, 230/1000 and 275/1200 Models ............................................ 27
Machine Anchoring - 90/400 and 125/520 Models
With Tilt Option ................................................................................. 29
Machine Anchoring - 180/800, 230/1000 and 275/1200
Models With Tilt Option .................................................................... 30
Connections .......................................................................................... 31
Water Connection ............................................................................ 31
Water Consumption ......................................................................... 32
Water Drain Connection .................................................................. 32
Steam Connection ............................................................................ 32
Venting............................................................................................. 33
Electrical Connection....................................................................... 33
Liquid Soap Connection .................................................................. 39
Electrical Connection....................................................................... 40
Electronic Controller with Blue PCB and Graphical Display ......... 40

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
2D1590ENR2
Putting the Machine into Service.......................................................... 41
Models 75/335, 90/400 and 125/520 ............................................... 41
Models 90/400 and 125/520
with Tilt Option .............................................................................. 41
Models 180/800, 230/1000 and 275/1200 ....................................... 42
Checking Before Putting into Service.............................................. 42
Operation............................................................................................. 43
Symbols on the Machine ...................................................................... 43
Hanging Control (Washers with Tilting System) ............................ 44
Micro Microprocessor...................................................................... 45
Before Washing .................................................................................... 46
Opening the Door ................................................................................. 46
Loading the Machine with Linen.......................................................... 46
Closing the Door................................................................................... 46
Program Selection................................................................................. 46
Wash Programs Overview .................................................................... 47
Add Detergent....................................................................................... 47
Start the Washer.................................................................................... 48
Micro Microprocessor...................................................................... 48
End of Wash Cycle ............................................................................... 48
Models with the Tilt Option - Tilting the Machine Forward
to a Position Suitable for Unloading the Linen .............................. 48
Models with the Tilt Option - Unloading the Linen ........................ 49
Models with the Tilt Option - Tilting the Machine to the
Basic Position ................................................................................. 49
Maintenance ........................................................................................ 50
Introduction........................................................................................... 50
Daily ..................................................................................................... 50
Monthly or After 200 Working Hours.................................................. 50
Every 3 Months or After 500 Working Hours...................................... 50
Every 6 Months or After 1000 Working Hours.................................... 51
Safety Vibration Switch........................................................................ 51
Function Description - Models 75/335,
90/400 and 125/520 ........................................................................ 51
Function Description - Models 180/800, 230/1000
and 275/1200 .................................................................................. 51
Sensibility Adjustment - Models 75/335, 90/400
and 125/520 .................................................................................... 52
Sensibility Adjustment - Models 180/800, 230/1000
and 275/1200 .................................................................................. 52
Lubrication............................................................................................ 57
Lubrication Points, Quantity and Lubrication Periods -
Models 75/335, 90/400 and 125/520.............................................. 57
Lubrication Points, Quantity and Lubrication Periods -
Models 180/800,
230/1000 and 275/1200 .................................................................. 57

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
D1590ENR2 3
Driving Mechanism .............................................................................. 58
Inspection of Belt Tightness ............................................................ 58
Belt Replacement ............................................................................. 58
Pulley Alignment ............................................................................. 58
Steam Filters ......................................................................................... 59
Cleaning the Filter............................................................................ 59
Thrust of Door Seal .............................................................................. 59
Adjusting on the Side of the Door Handle....................................... 59
Spring Unit - Models 75/335, 90/400 and 125/520 .............................. 61
Spring Unit - Models 180/800, 230/1000 and 275/1200 ...................... 62
Replacement Washer Fuses .................................................................. 62
Fuse Values...................................................................................... 62
Earth Leakage Trips.............................................................................. 62
The Test Procedure .......................................................................... 62
Troubleshooting Aids ......................................................................... 63
Door Blocking ...................................................................................... 63
Description of Door Lock Function................................................. 63
Lock without Tensions before the Program Start ............................ 63
Main Switch and Emergency Stop Button are Switched On ........... 63
Current Failure During Operation.................................................... 63
Unblocking the Door Lock in Case of Emergency.......................... 63
Error Indication Shown on Display ...................................................... 64
Putting the Machine out of Service ................................................... 65
Disconnecting the Machine .................................................................. 65
Machine Disposal ................................................................................. 66
Possibility of the Machine Disposal by a Specialized Company..... 66
Possibility of the Machine Liquidation by Own Potential............... 66

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
4D1590ENR2
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
Important Safety Instructions
This English version is the original version of this
manual. Without this version, the instructions are
incomplete.
Before installation, operation and maintenance of the
machine read carefully the complete instructions,
i.e., this “Installation, maintenance and user's
manual”, “Programming manual” and “Spare parts
manual”. The Spare parts manual is not delivered with
a machine by default. You shall ask the supplier/
manufacturer to obtain Spare parts manual.
1. Read all instructions before using the washer.
2. Install the washer according the
INSTALLATION instructions. Refer to the
EARTHING (grounding) instructions in the
INSTALLATION manual for the proper earthing
(grounding) of the washer. All connections for
water, drain, electrical power and earthing
(grounding) must comply with local codes and be
made by licensed personnel when required. It is
recommended that the machine be installed by
qualified technicians.
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
DANGER
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
CAUTION
SAVE THESE INSTRUCTIONS FOR LATER
USE. Failure to comply with the
instructions may lead to incorrect use of
the appliance, and may result in risk of fire,
bodily injuries or death and/or damage to
the laundry and/or the appliance.
W828
WARNING
Read the IMPORTANT SAFETY
INSTRUCTIONS in this manual carefully
before operating the appliance. Improper
use of the appliance may cause risk of fire,
electrical shock or serious body injuries or
death as well as serious damage to the
appliance.
W829
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
WARNING

Safety Information
5
D1590ENR2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3. Do not install or store the washer where it will be
exposed to water and/or weather.
4. To prevent fire and explosion, keep the area
around machine free from flammable and
combustible products. Do not add the following
substances or textiles containing traces of the
following substances to the wash water: gasoline,
kerosene, waxes, cooking oils, vegetable oils,
machine oils, dry-cleaning solvents, flammable
chemicals, thinners, or other flammable or
explosive substances. These substances give off
vapors that could ignite, explode or cause the
fabric to catch fire by itself.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
7. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This appliance
is not intended for use by young children or
infirm persons without supervision. Young
children should be supervised to ensure that they
do not play with the appliance. This is a safety
rule for all appliances.
8. DO NOT reach and/or climb into the tub or onto
the washer, ESPECIALLY if the wash drum is
moving. This is an imminently hazardous
situation that, if not avoided, will cause severe
personal injury or death.
9. Never operate the washer with any guards, panels
and/or parts removed or broken. DO NOT bypass
any safety devices or tamper with the controls.
10. Use washer only for its intended purpose,
washing textiles. Never wash machine parts or
automotive parts in the machine. This could
result in serious damage to the basket or tub.
11. Use only low-sudsing, no-foaming types of
commercial detergent. Be aware that hazardous
chemicals may be present. Wear hand and eye
protection when adding detergents and
chemicals. Always read and follow
manufacturer’s instructions on packages of
laundry and cleaning aids. Heed all warnings or
precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of
children at all times (preferably in a locked
cabinet).
12. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
13. Always follow the fabric care instructions
supplied by the textile manufacturer.
14. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open. Do not
attempt to open the door until the washer has
drained and all moving parts have stopped.
15. Be aware that hot water is used to flush the
supply dispenser. Avoid opening the dispenser lid
while the machine is running.
16. Do not attach anything to the supply dispenser’s
nozzles, if applicable. The air gap must be
maintained.
17. Do not operate the machine without the water
reuse plug or water reuse system in place, if
applicable.
18. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
20. DANGER: Before inspecting or servicing
machine, power supply must be turned OFF. The
servicer needs to wait for at least 10 minutes after
turning the power OFF and needs to check for
residual voltage with a voltage meter. The
inverter remains charged with high voltage for
some time after powering OFF. This is an
imminently hazardous situation that, if not
avoided, will cause severe personal injury or
death. Before starting inspection of the inverter,
check for residual voltage across main circuit
terminals + and -. This voltage must be below 30
VDC before the servicer can access the inverter
for inspection.
21. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out. ALWAYS disconnect the
washer from electrical, power and water supplies
before attempting any service.
22. Disconnect the power by turning off the circuit
breaker or by unplugging the machine. Replace
worn power cords.
23. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
24. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Safety Information
D1590ENR2
6
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Always contact your dealer, distributor, service agent
or the manufacturer on any problems or conditions you
do not understand.
This appliance must be connected to a
grounded metal, permanent wiring system,
and additionally an equipment-grounding
conductor must be run with the circuit
conductors and connected to the
equipment-grounding terminal or lead on
the appliance.
W830
WARNING
In order to minimize the risk of fire,
electrical shock and injury, THIS WASHER
MUST BE PROPERLY GROUNDED. Never
plug in or direct-wire an appliance unless it
is properly grounded in accordance with
all local and national codes. If more
appliances are in the same location,
mutual grounding must be applied where
possible.
W831
WARNING
It is recommended to consult static
requirements with a static engineer to
meet the requirements of permissible
loading, vibrations and noise level in the
building.
W839
WARNING
CFD822N
Figure 1
The washer extractor is intended to be
permanently connected, it MUST be
secured mounted to a NON-
COMBUSTIBLE, adequate floor structure.
NEVER install the washer on an upper
floor or over a basement without a load
support designed by a structural engineer.
W832
WARNING
Always disconnect the washer from the
electrical supply before attempting any
service. The washer extractor is out of
tension if the main plug is taken out or
when the main supply is disconnected.
When the main switch is turned off the
inlet terminals of the machine main switch
are still under current!
W834
WARNING
CFD822N
W835
W836
Extreme hot conditions can arise in the air
around the machine. Watch out for vapor
that escapes from the washer extractor
venting!
W835
CAUTION
Do not cover the washer extractor venting.
It serves as a vapor outlet to prevent
pressure building in the washer extractor.
W836
CAUTION

Safety Information
7
D1590ENR2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Safety Decals
Important Information Before
Installation
Transportation and Storage
IMPORTANT: In case of transportation and
storage, watch components protruding from the
contour line of machine (door locks, etc.) to avoid
injuries.
•Never push, pull or exert pressure on components
protruding from the machine contour line
(controls, door locks, etc.).
•Make sure that these components are secured so
as to avoid damages during machine
manipulation and installation.
•In case of machine transportation by the
customer, follow the manufacturer’s instructions
for transportation, handling and storage of the
product. In case of transportation of the machine
by customer, the manufacturer is not responsible
for possible damage to the machine in the course
of transportation. In case of storing the machine
in a free area, it must be protected against
mechanical damage and weather conditions.
For Installation
IMPORTANT: All connections must be performed
by qualified personnel with a proper authorization
according to this manual in compliance with local
standards
•The washer must not be installed or stored in an
area where it will be exposed to water and/or
weather. Avoid damp conditions where water or
moisture could run down the walls and covers of
the washer or cover the floor around the washer.
Do not install the washer above an open gutter.
Close any nearby gutters so that the waste water
steam cannot collect near/inside the washer.
•Any changes in the machine installation must be
approved by the dealer or manufacturer.
Otherwise, the dealer or manufacturer is not
responsible for possible injuries or damages.
Interference and changes in the machine
construction are not allowed and the
manufacturer refuses an responsibilities in such
cases.
•Define dangerous areas in the laundry room and
do not allow people to enter if the machine is in
operation.
Machine Information
•This manual comprises information for the soft-
mount machine series 75/335, 90/400, 125/520,
180/800, 230/1000 and 275/1200. Verify the
machine model according to your order and the
data plate located on the machine rear and find
corresponding information in the manual.
•The machines are controlled by electronic
controller. Find the programming instructions in
the Programming Manual.
•Additional heating can be provided by electrical
heating elements or by steam from an external
steam supply.
•Water inlets can use warm, cold, soft and cold
hard water. A machine can be equipped with
recycled discharging, dosing pumps for liquid
soaps and/or a tilting system.
•Electrical setup of the machine is indicated on the
data plate (Figure 2, pos. 11).
Do not remove warning signs placed on
the appliance. Observe signs and labels to
avoid personal injuries. Safety labels
appear at crucial locations on the
appliance. Failure to maintain legible
safety labels could result in injury to the
operator or service technician.
W833
WARNING
Original or identical parts must be used for
replacement in this machine. After
servicing, replace and secure all panels in
the original way. Take these measures for
continued protection against electrical
shock, injury, fire and/or property damage.
W837
WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
8D1590ENR2
Introduction
Model Identification
Information in this manual is applicable to the
following models:
HY125_MICRO
HY90_MICRO
HYN125W
HYN90W
IX180_MICRO
IX230_MICRO
IX275_MICRO
IXR180W
IXR230W
IXR275W
IY125_MICRO
IY180_MICRO
IY230_MICRO
IY275_MICRO
IY90_MICRO
IYN090W
IYN125W
SY125_MICRO
SY90_MICRO
SYN090W
SYN125W
UX180_MICRO
UX230_MICRO
UX275_MICRO
UXR180W
UXR230W
UXR275W
UY125_MICRO
UY180_MICRO
UY230_MICRO
UY275_MICRO
UY90_MICRO
UYN090W
UYN125W
UYN180W
UYN230W
UYN275W

Introduction
9
D1590ENR2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Replacement Parts
If literature or replacement parts are required, contact
the source from which the machine was purchased or
contact Alliance Laundry Systems at
[phone] for the name and address of the
nearest authorized parts distributor.
Customer Service
Contact your local distributor or call:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: [phone]
Ripon, Wisconsin
Alliance International
[phone]
Wevelgem, Belgium

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
10 D1590ENR2
Technical Specifications
Specification 75/335 90/400 125/520 180/800 230/1000 275/1200
Machine Dimensions1– Models Without Tilt Option
Width
Depth
Height
mm/inch
mm/inch
mm/inch
1195/47.04
1330/52.40
1905/75.00
1195/47.04
1430/56.30
1905/75.00
1195/47.04
1610/63.40
1905/75.00
1495/58.86
1940/76.38
1985/78.15
1790/70.47
2005/78.94
2060/81.10
1855/73.03
2085/82.09
2085/82.09
Machine Dimensions1– Models With Tilt Option
Width
Depth
Height
mm/inch
mm/inch
mm/inch
-
-
-
-
-
-
-
-
-
1565/61.61
2020/79.53
2215/87.20
1855/73.03
2100/82.68
2300/90.55
1895/74.61
2155/84.84
2335/91.93
Packing Dimensions – Models Without Tilt Option
Width
Depth
Height
Transportation volume
mm/inch
mm/inch
mm/inch
m³/ft³
1430/56.30
1475/58.10
2105/82.90
4.4/156
1430/56.30
1570/61.80
2105/82.90
4.7/166
1430/56.30
1750/68.90
2105/82.90
5.3/187
1690/66.53
1950/76.77
2200/86.61
7.25/256
1865/73.42
2125/83.66
2345/92.33
9.29/328
2000/78.73
2170/85.43
2340/92.12
10.16/359
Packing Dimensions – Models With Tilt Option
Width
Depth
Height
Transportation volume
mm/inch
mm/inch
mm/inch
m³/ft³
-
-
-
-
-
-
-
-
-
-
-
-
1690/66.54
2075/81.69
2440/96.06
8.90/314
2040/80.31
2375/93.50
2490/98.03
11.85/419
2040/80.31
2375/93.50
2490/98.03
12.42/439
Drum Dimensions
Diameter
Depth
Drum volume
Door opening
mm/inch
mm/inch
dm³/gal.
mm/inch
914/36.00
510/20
335/88
540/21.30
914/36.00
610/24
400/106
540/21.30
914/36.00
790/31.10
518/137
540/21.30
1110/43.70
838/33
807/213
530/20.86
1200/47.24
860/33.85
1003/265
530/20.86
1300/51.18
870/34.25
1180/312
650/25.59
Weight – Models Without Tilt Option
Net
Gross
kg/lb.
kg/lb.
1190/2623
1310/2888
1560/3439
1700/3748
1630/3594
1770/3902
2640/5820
2830/6239
3170/6989
3410/7518
3480/7672
3710/8179
Weight – Models With Tilt Option
Net
Gross
kg/lb.
kg/lb.
-
-
-
-
-
-
2990/6592
3210/7077
3520/7761
3760/8290
3840/8466
4060/8951
Electrical Data
Power supply deviations
3x380-415V 50/60Hz
3x440-480V 50/60Hz
3x200-240V 50/60Hz
3x208-240V 50/60Hz
3x380-480V 50/60HZ
-6% to +10% of the voltage supply ±1 Hz
Motor output kW 4 7.5 7.5 11 15 18.5
Input Power
Electric heating
24kW kW 28.1 - - - - -
Electric heating
36kW kW - 43.6 - - - -
Electric heating
54kW (380-480V) kW --61.6---
Electric heating
67.5kW kW ---75--
Steam or without heating kW 4.1 7.6 7.6 11.25 15.25 18.75
Table 1 (Continued)

Technical Specifications
11
D1590ENR2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Table 1 (Continued)
Specification 75/335 90/400 125/520 180/800 230/1000 275/1200
Supply Protection Device Use slow type Protection devices (circuit breakers: curve D)
Residual current device
(RCD) mA 100, class B 100, class B 100, class B 100, class B 100, class B 100, class B
Steam or without heating
200-240V 3AC
380-480V 3AC
3x208-240V 50/60Hz
3x380-480V 50/60 Hz
A
A
A
A
30
16 (15)
-
-
40
20
-
-
40
20
-
-
-
-
63
32
-
-
75
50
-
-
100
63
El. Heating 24kW (220-240V) A
El. Heating 24kW (380-415V) A
El. Heating 24kW (440-480V) A
El. Heating 36kW (200-240V) A
El. Heating 36kW (380-480V) A
El. Heating 54kW (220-240V) A
El. Heating 54kW (380-480V) A
El. Heating 67.5kW (3x208-240V) A
El. Heating 67.5kW (3x208-240V) A
80
50
32
-
-
-
-
-
-
-
-
-
120
80
-
-
-
-
-
-
-
-
-
160
100
-
-
-
-
-
-
-
-
-
250
125
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Washing Functions
Washing
High extracting
RPM
RPM
38
830
38
830
38
830
36
750
33
720
32
695
G-factor 350 350 350 350 350 350
Connection Data
Water inlet connection inch BSP 1” 3 x BSP 1½”
Water pressure range MPa/bar/PSI 0.1 - 0.8/1 - 8/14.5 - 116
Recommended
water pressure MPa/bar/PSI 0.3 - 0.5/3 - 5/43 - 73
Maximal water temperature °C/°F90/194 90/194 90/194 90/194 90/194 90/194
Drain diameter mm/inch 2 x 76/3 2 x 76/3 2 x 76/3 2 x 103/4 2 x 103/4 2 x Ø103/4
Drain flow rate dm³ min-1
gal. min-1
300
80
300
80
300
80
540
142
516
136
516
136
Steam connection inch G 3/4 in. G 3/4 in. G 3/4 in. G 1 in. G 1 in. G 1 in.
Steam pressure MPA/bar/PSI 0.3 - 0.5/3 - 5/43 - 73
Press air connection2mm/inch 6/0.25 6/0.25 6/0.25 8/0.30 8/0.30 Ø 8/0.30
Not lubricated air pressure MPa/bar/PSI 0.3 - 0.5/3 -
5/43 - 73
0.3 - 0.5/3 -
5/43 - 73
0.3 - 0.5/3 -
5/43 - 73 0.6/6/87 0.6/6/87 0.6/6/87
Powder dispenser cups
Liquid soap signals
5
8 pumps
5
8 pumps
5
8 pumps
5
8 pumps
5
8 pumps
5
8 pumps
External liquid soap connections 666
6 tubes:
1 x ½ in.
6 tubes:
1 x ½ in. 1 x ½ in.
Hose for press air
connection
(Models with tilt
option only)
mm/inch -
8/0.31
outside
diameter
8/0.31
outside
diameter
8/0.31
outside
diameter
8/0.31
outside
diameter
8/0.31
outside
diameter
Air pressure
(Models with tilt
option only)
MPa/bar/PSI - 0.35/3.5/51 0.35/3.5/51 0.35/3.5/51 0.35/3.5/51 0.35/3.5/51
Motor Size KW/HP 4.0/5.36 7.5/10.06 7.5/10.06 11.0/14.75 15.0/20.12 18.5/24.81
Table 1 (Continued)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Technical Specifications
D1590ENR2
12
Table 1
Table 1 (Continued)
Specification 75/335 90/400 125/520 180/800 230/1000 275/1200
General Data
Ambient temperature
Relative humidity
Height above sea level
Storage temperature
°C/°F
m/ft.
°C/°F
5 to 35/41 to 95
30% to 90% without condensation
up to 1000/3280
1 to 55/34 to 131
Max. static load on floor
(Models without tilt
option)
Max. static load on floor
(Models with tilt option)
Max. dynamic load on
floor (Models without tilt
option)
Max. dynamic load on
floor (Models with tilt
option)
Frequency of dynamic
load
kN
kN
kN
kN
Hz
14.41
-
12.7 ± 2.74
-
14
18.16
19.4
16.08 ± 2.94
17.11 ± 2.94
14
19.57
20.86
17.06 ± 3.13
18.13 ± 3.13
14
30.9
34.4
27.2 ± 4.5
30.6 ± 4.5
12.5
36.9
40.4
32.7 ± 5.5
36.1 ± 5.5
12.1
40.4
43.9
36.0 ± 7.0
39.5 ± 7.0
11.7
Sound Levels3
LAeq wash/extraction seq. db 55/75 55/75 55/75 51/71 52/72 52/72
1maximum dimensions including protruding parts
2washers with air operated water valves
3ISO 3744

Technical Specifications
13
D1590ENR2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
75/335, 90/400 and 125/520 Models Without Tilt Option
NOTE: Refer to following page for dimensions.
1Operator Panel 11 Data plate
2Tub ventilation (60 mm/2.4 in.) 12 Steam inlet
3Lubrication points 13 Equipotential bounding terminal
4Entry soap supply cable 14 Drain outlet
5Entry main power cable 15 Soap dispenser air relieve
6Main switch 16 Frequency inverter cover
7Hard cold water inlet 17 Compressed air inlet
8Hot water inlet (Models with air operated water valves)
9Soft cold water inlet 18 Soap dispenser
10 Hose connection soap supply 19 Electrical signals liquid soap
Figure 2
18
15
G
X
A
AA
1
H
K
T
A1
R
D1
P
C
B
F
Z
D
E
L
C1
JO
MN
Q
B1
S
U
WV
H1
2
3
13
16
4
56 7 8 9
11
13
10
19
G1
17
12
1414
CFD988N

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Technical Specifications
D1590ENR2
14
Machine Dimensions – Models Without Tilt Option
MACHINE 75/335 90/400 125/520
A mm/inch 1195/47.04 1195/47.04 1195/47.04
A1 mm/inch 1361/53.58 1361/53.58 1361/53.58
B mm/inch 1905/75 1905/75 1905/75
B1 mm/inch 116/4.56 116/4.56 116/4.56
C mm/inch 1055/41.54 1055/41.54 1055/41.54
C1 mm/inch 980/38.58 980/38.58 980/38.58
D mm/inch 1330/52.4 1430/56.3 1610/63.39
D1 mm/inch 1600/62.99 1600/62.99 1600/62.99
E mm/inch 1222/48.11 1322/52.05 1502/59.13
Fmm/inch 300/11.8 300/11.8 300/11.8
G mm/inch 50/1.97 50/1.97 50/1.97
G1 mm/inch 110/4.33 110/4.33 110/4.33
H mm/inch 1617/63.66 1617/63.66 1617/63.66
H1 mm/inch 25/0.98 25/0.98 25/0.98
J mm/inch 730/28.74 730/28.74 730/28.74
K mm/inch 1567/61.69 1567/61.69 1567/61.69
L mm/inch 422/16.61 422/16.61 422/16.61
M mm/inch 80/3.15 80/3.15 80/3.15
N mm/inch 80/3.15 80/3.15 80/3.15
O mm/inch 70/2.75 70/2.75 70/2.75
P mm/inch 1782/70.16 1782/70.16 1782/70.16
P* mm/inch 1672/65.82 1672/65.82 1672/65.82
Q mm/inch 60/2.36 60/2.36 60/2.36
R mm/inch 1285/50.59 1285/50.59 1285/50.59
S mm/inch 65/2.56 65/2.56 65/2.56
T mm/inch 768/30.24 768/30.24 768/30.24
Umm/inch 205/8.07 205/8.07 205/8.07
Vmm/inch 213/8.39 213/8.39 213/8.39
Wmm/inch 420/16.54 275/10.83 275/10.83
Xmm/inch 175/6.89 175/6.89 175/6.89
Zmm/inch 700/27.56 700/27.56 700/27.56
AA mm/inch 730/28.74 730/28.74 730/28.74
* Models with air-operated water valves
Table 2

Technical Specifications
15
D1590ENR2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
180/800, 230/1000 and 275/1200 Models Without Tilt Option
NOTE: Refer to following page for dimensions.
CFD945N
1Box of electrical components 10 Hard cold water inlet
2Soap dispenser ventilation 11 Soft cold water inlet
3Control panel 12 Hot water inlet
4Soap dispenser 13 Compressed air inlet
5Electrical signals liquid soap 14 Entry main power cable
6Steam inlet 15 Main switch
7Tub ventilation 16 Drain outlet
8Cover for pneumatic components 17 Electric switchboard cover
9Hose connection soap supply 18 Serial label
Figure 3
A
B
E
F
D
R
Z
Q
O
P
V
ST
X
Y
C
U
M
N
G
HIJKL
W
16
14
15
67
13
5
9
10
11
12 17
4
8
1220319
18

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Technical Specifications
D1590ENR2
16
Machine Dimensions – Models Without Tilt Option
MACHINE 180/800 230/1000 275/1200
A mm/inch 1495/58.86 1790/70.47 1855/73.03
B mm/inch 1985/78.15 2060/81.10 2085/82.09
C mm/inch 1940/76.38 2005/78.94 2085/82.09
D mm/inch 1390/54.72 1688/66.46 1754/69.05
E mm/inch 1133/44.60 1175/46.26 1200/47.24
Fmm/inch 1020/40.16 1095/43.11 1080/42.52
G mm/inch 303/11.93 232/9.13 295/11.61
H mm/inch 168/6.61 232/9.13 247/9.72
Imm/inch 125/4.92 125/4.92 125/4.92
J mm/inch 125/4.92 125/4.92 125/4.92
K mm/inch 90/3.54 124/4.88 120/4.72
L mm/inch 100/3.93 110/4.33 148/5.83
M mm/inch 83/3.27 83/3.27 83/3.27
N mm/inch 210/8.26 210/8.26 210/8.26
O mm/inch 1900/74.80 1518/59.76 1548/60.94
P(1) mm/inch 1787/70.35 1405/55.31 1435/56.50
Q mm/inch 1983/78.07 1950/76.77 1980/77.95
R mm/inch 1460/57.48 1754/69.05 1820/71.65
S mm/inch 282/11.10 268/10.55 243/9.57
T mm/inch 437/17.20 419/16.50 394/15.51
Umm/inch 662/26.06 696/27.40 722/28.43
Vmm/inch 735/28.93 768/30.24 795/31.30
Wmm/inch 197/7.76 197/7.76 197/7.76
Xmm/inch 380/14.96 527/20.75 562/22.13
Ymm/inch 665/26.18 650/25.59 757/29.80
Z(2) mm/inch 1787/70.53 1836/72.28 1866/73.46
(1) Height of item 9
(2) Height of items 6, 7, 10, 11 and 12
Table 3

Technical Specifications
17
D1590ENR2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
180/800 Models With Tilt Option
NOTE: Refer to following page for dimensions.
CFD980N
Figure 4
CFD980N
FRONT VIEW LEFT SIDE VIEW BACK VIEW
VIEW FROM ABOVE
A
G
F
D
C
B
E
HJ
IK
L
M
V
TU
S
R
PQ
N
O
LEFT SIDE VIEW OF TILTING
FRONT VIEW OF TILTING
W
X
Y
Z
AA

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Technical Specifications
D1590ENR2
18
Machine Dimensions – Models With Tilt Option
Dimensions 180/800
Amm/inch 2215/87.20
Bmm/inch 1908/75.12
Cmm/inch 1850/72.83
Dmm/inch 1037/40.83
Emm/inch 988/38.90
Fmm/inch 1565/61.61
Gmm/inch 1019/40.12
Hmm/inch 2020/79.53
Imm/inch 705/27.76
Jmm/inch 468/18.43
Kmm/inch 491/19.33
Lmm/inch 155/6.10
Mmm/inch 407/16.02
Nmm/inch 140°
Omm/inch 424/16.69
Pmm/inch 146°
Qmm/inch 541/21.30
Rmm/inch 219/8.62
Smm/inch 966/38.03
Tmm/inch 851/33.50
Umm/inch 812/31.97
Vmm/inch 2476/97.48
Wmm/inch 983/38.70
Xmm/inch 837/32.95
Ymm/inch 15°
Zmm/inch 2380/93.70
AA mm/inch 2009/79.09
Table 4