Allied Telesis AT-FS716 User manual

AT-FS716
AT-FS716E
AT-FS724I
Fast Ethernet Switches
Installation Guide
PN 613-10804-00 Rev. A

Copyright ”1999 Allied Telesyn International, Corp.
960 Stewart Drive Suite B, Sunnyvale CA 94086, USA
All rights reserved. No part of this publication may be reproduced without prior written permission
from Allied Telesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their
respective owners.
Allied Telesyn International,Corp. reserves the right to make changes in specificationsand other
information contained in this document without prior written notice. The information provided
herein is subject to change without notice. In no event shall Allied Telesyn International, Corp. be
liable for any incidental, special, indirect, or consequential damages whatsoever, including but not
limited to lost profits, arising out of or related to this manual or the information contained herein,
even if Allied Telesyn International, Corp. has been advised of, known, or should have known, the
possibility of such damages.

iii
Electrical Safety and Installation
Requirements For AT-FS724I
STANDARDS: This product meets the following standards
RFI Emission EN55022 Class A
WARNING: In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Immunity EN50082-1
Electrical Safety TUV-EN60950, UL1950, CSA 950
NORMEN: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Hochfrequenzstörung EN55022 Klasse A
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In
diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen.
Störsicherheit EN50082-1
Elektrische Sicherheit TUV-EN60950, UL1950, CSA 950
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and , if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the
FCC, can void your right to operate this equipment.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.

iv
Electrical Safety and Installation Requirements For AT-FS724I
STANDARDER: Dette produkt tilfredsstiller de følgende standarder.
Radiofrekvens forstyrrelsesemission EN55022 Klasse A
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det
tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger.
Immunitet EN50082-1
Elektrisk sikkerhed TUV-EN60950, UL1950, CSA 950
EISEN: Dit product voldoet aan de volgende eisen.
RFI Emissie EN55022 Klasse A
WAARSCHUWING:Binnenshuiskanditproductradiostoringveroorzaken,inwelkgevaldegebruiker
verplicht kan worden om gepaste maatregelen te nemen.
Immuniteit EN50082-1
Electrische Veiligheid TUV-EN60950, UL1950, CSA 950
NORMES: ce produit est conforme aux normes de suivantes :
Emission d’interférences radioélectriques EN55022 Classe A
MISEENGARDE:dansunenvironnementdomestique,ceproduitpeutprovoquerdesinterférences
radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates.
Immunité EN50082 - 1
Sécurité électrique TUV-EN60950, UL1950, CSA 950
STANDARDIT: Tämä tuote on seuraavien standardien mukainen.
Radioaaltojen häirintä EN55022 Luokka A
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin.
Kestävyys EN50082-1
Sähköturvallisuus TUV-EN60950, UL1950, CSA 950
STANDARD: Questo prodotto è conforme ai seguenti standard.
Emissione RFI (interferenza di radiofrequenza) EN55022 Classe A
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza.
In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti.
Immunità EN50082-1
Sicurezza elettrica TUV-EN60950, UL1950, CSA 950

v
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
SIKKERHETSNORMER: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
RFI stråling EN55022 Klasse A
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.
Immunitet EN50082-1
Elektrisk sikkerhet TUV-EN60950, UL1950, CSA 950
PADRÕES: Este produto atende aos seguintes padrões.
Emissão de interferência de radiofrequência EN55022 Classe A
AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção
e, neste caso, pode ser necessário que o utente tome as medidas adequadas.
Imunidade EN50082-1
Segurança Eléctrica TUV-EN60950, UL1950, CSA 950
ESTÁNDARES: Este producto cumple con los siguientes estándares.
Emisión RFI EN55022 Clase A
ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias,
en cuyo caso, puede requerirse del usuario quetome las medidas que seanconvenientes al
respecto.
Inmunidad EN50082-1
Seguridad eléctrica TUV-EN60950, UL1950, CSA 950
STANDARDER: Denna produkt uppfyller följande standarder.
Radiostörning EN55022 Klass A
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga
användaren till att vidtaga erforderliga åtgärder.
Immunitet EN50082-1
Elsäkerhet TUV-EN60950, UL1950, CSA 950

vi
Electrical Safety and Installation Requirements For AT-FS716 and AT-FS716E
Electrical Safety and Installation
Requirements For AT-FS716 and AT-FS716E
STANDARDS: This product meets the following standards.
Immunity EN50082-1
Electrical Safety TUV-EN60950, UL1950, CSA 950
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name: Allied Telesyn International
Manufacture Address: 950 Kifer Road
Sunnyvale, CA 94086 USA
Manufacture Telephone: [phone]
Declares that the product: Switches
Model Number: AT-FS716 and AT-FS716E
This product complies with FCC Part 15B, Class B Limits:
This device complieswith part 15 of the FCC Rules.Operation is subject to the following
two conditions: (1) This device must not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or registrant of
this equipment can void your authority to operate this equipment under Federal
Communications Commission rules.

vii
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
NORMEN: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Hochfrequenzstörung EN55022 Klasse B
Störsicherheit EN50082-1
Elektrische Sicherheit TUV-EN60950, UL1950, CSA 950
STANDARDER: Dette produkt tilfredsstiller de følgende standarder.
Radiofrekvens forstyrrelsesemission EN55022 Klasse B
Immunitet EN50082-1
Elektrisk sikkerhed TUV-EN60950, UL1950, CSA 950
EISEN: Dit product voldoet aan de volgende eisen.
RFI Emissie EN55022 Klasse B
Immuniteit EN50082-1
Electrische Veiligheid TUV-EN60950, UL1950, CSA 950
NORMES: ce produit est conforme aux normes de suivantes :
Emission d’interférences radioélectriques EN55022 Classe B
Immunité EN50082 - 1
Sécurité électrique TUV-EN60950, UL1950, CSA 950
STANDARDIT: Tämä tuote on seuraavien standardien mukainen.
Radioaaltojen häirintä EN55022 Luokka B
Kestävyys EN50082-1
Sähköturvallisuus TUV-EN60950, UL1950, CSA 950
STANDARD: Questo prodotto è conforme ai seguenti standard.
Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B
Immunità EN50082-1
Sicurezza elettrica TUV-EN60950, UL1950, CSA 950
SIKKERHETSNORMER: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
RFI stråling EN55022 Klasse B
Immunitet EN50082-1
Elektrisk sikkerhet TUV-EN60950, UL1950, CSA 950

viii
Electrical Safety and Installation Requirements For AT-FS716 and AT-FS716E
PADRÕES: Este produto atende aos seguintes padrões.
Emissão de interferência de radiofrequência EN55022 Classe B
Imunidade EN50082-1
Segurança Eléctrica TUV-EN60950, UL1950, CSA 950
ESTÁNDARES: Este producto cumple con los siguientes estándares.
Emisión RFI EN55022 Clase B
Inmunidad EN50082-1
Seguridad eléctrica TUV-EN60950, UL1950, CSA 950
STANDARDER: Denna produkt uppfyller följande standarder.
Radiostörning EN55022 Klass B
Immunitet EN50082-1
Elsäkerhet TUV-EN60950, UL1950, CSA 950

ix
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
Safety Information (All Products)
SAFETY
ELECTRICAL NOTICES
WARNING: ELECTRIC SHOCK HAZARD
To prevent ELECTRIC shock , do not remove cover. No user-serviceable parts inside. This
unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified
technician. To avoid the possibility of ELECTRIC SHOCK disconnect electric power to the
product before connecting or disconnecting the LAN cables.
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING
ACTIVITY.
INSTALLATION
ELECTRICAL—AUTO VOLTAGE ADJUSTMENT
This product will automatically adjust to any voltage between the ranges shown on the
label.
ELECTRICAL—TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a properly wired
earth ground socket outlet. An improperly wired socket outlet could place hazardous
voltages on accessible metal parts.
ELECTRICAL—CORD NOTICE
Use power cord, maximum 4.5 meters long, rated 6 amp minimum, 250V, made of HAR
cordage molded IEC 320 connector on one end and on the other end a plug approved by
the country of end use.
CAUTION: Air vents must not be blocked and must have free access to the room ambient
air for cooling.
OPERATING TEMPERATURE
This product is designed for a maximum ambient temperature of 40 degrees C.
ALL COUNTRIES: Install product in accordance with local and National Electrical Codes.
SICHERHEIT
ACHTUNG: GEFÄHRLICHE SPANNUNG
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile. Das Gerät
steht unter Hochspannung und darf nur von qualifiziertem technischem Personal geöffnet
werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen.
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters ausführen.
INSTALLATION
AUTOMATISCHE SPANNUNGSEINSTELLUNG
Dieses Gerät stellt sich automatisch auf die auf dem Etikett aufgeführten Spannungswerte
ein.
GERÄTE DER KLASSE 1
DIESE GERÄTE MÜSSEN GEERDET SEIN. DerNetzstecker darf nur mit einer
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger
Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische Spannungen
setzen.

x
Safety Information (All Products)
NETZKABEL
Das Netzkabel sollte eine maximale Länge von 4,5 Metern, einen Nennwert von mindestens
6 A und 250 V haben, aus HAR-Material hergestellt und mit einer gepreßten, IEC 320
entsprechenden, Anschlußverbindung an einem Ende, und am anderen Ende mit einem im
Land des Endverbrauchers geprüften Stecker ausgestattet sein.
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien
Zugang zur Raumluft haben.
BETRIEBSTEMPERATUR
Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als
40° C entworfen.
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften
entsprechen.
SIKKERHED
ELEKTRISKE FORHOLDSREGLER
ADVARSEL: RISIKO FOR ELEKTRISK STØD
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der kan
repareres af brugeren. Denne enhed indeholder LIVSFARLIGE STRØMSPÆNDINGER og
bør kun åbnes af en uddannet og kvalificeret tekniker. For at undgå risiko for ELEKTRISK
STØD, afbrydes den elektriske strøm til produktet, før LAN-kablerne monteres eller
afmonteres.
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.
INSTALLATION
ELEKTRISK—AUTOMATISK SPÆNDINGSREGULERING
Dette apparat vil automatisk tilpasse sig enhver spænding indenfor de værdier,der er angivet
på etiketten.
ELEKTRISK—KLASSE 1-UDSTYR
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en korrekt
installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt kan sætte livsfarlig
spænding til tilgængelige metaldele.
ELEKTRISK—EDNING
Anvend ledning af maksimum 4,5 meters længde, med en kapacitet på minimum 6 amp.,
250 v, bestående af en IEC 320 connector med indstøbt HAR ledning i den ene ende og et
stik i den anden ende, der er godkendt af myndighederne i brugerlandet.
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den
omgivende luft i rummet for afkøling.
BETJENINGSTEMPERATUR
Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C.
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national
lovgivning for elektriske installationer.