Allnet ALL-HPNA3 User manual

ALLNET ALL-HPNA3
Home Phoneline Networking Alliance 3
Ethernet Bridge
User’s Manual

- 1 -
INTRODUCTION
This HomePNA to Ethernet bridge connects any
Ethernet device to a high speed access device or to a
Home Networking LAN for Internet access. This
bridge brings you the newest Ethernet compatible
technology that uses the telephone wiring as the net-
work's physical wiring thereby eliminating the need to
install new wiring. It is designed to operate on the
telephone wire installed in homes.
This bridge allows you to connect PC’s and Ethernet
enabled devices, such as DSL Modem, PC, HUB and
STB, to a Home Networking LAN by simply Plugging
into the existing RJ-11 jacks.
Features
•Plug & Play
•Using existing phoneline to build a network
•Shares Internet access and streaming video
•1 port HPNA connection compliant with
HomePNA 3.1 standard
•2 Standard 10/100 Fast Ethernet ports for con-
necting to Ethernet or DSL modem
•MDI/MDIX Auto Crossover Support
•QoS Priority Mapping Support
•QoS, TagVLAN, IGMP Snooping Support
•Statistic and Status Information Support

- 2 -
HARDWARE INSTALLATION
Parts Names and Functions
LED Indicators on the Rear Panel
Ansch-
luss
LED
Status
AN Blinkt AUS
DC IN
PWR Powered by
DC 5V – 1A
n/a
Not powered
LAN1
Link
Act
Link
Receive or
Transmit
Disconnect or
Link fail
LAN2
Link
Act Link
Receive or
Transmit
Disconnect or
Link fail
HPNA
Link
Act
Quality
Link
Receive or
Transmit
Disconnect or
Link fail
Green: High
Orange:
Medium
Red: Low

- 3 -
Ports on the Rear Panel
Port Name
Type Functions
A
DC IN DC Connects to the power adapter
plug.
B
LAN1 / LAN2
(Ethernet) RJ-45
Connects to Ethernet port on
FTTH/xDSL Modem,
Switch/HUB, PC and STB
for
Internet Access.
C
Phone RJ-11
Connect to Phone
D
HPNA RJ-11
Connect to other HPNA devices
Hardware Connections
1. Select a convenient location for the bridge
near the PC or Ethernet device to which it
will be connected. The bridge should be kept
away from excessive heat.
2. Using one telephone wire to connect the
HPNA port to RJ-11 jack on the wall. Using
another telephone wire to connect the other
Phone port to a telephone set (or connect
the Phone port to “phone” port of splitter of
ADSL modem).

- 4 -
3. Connect the LAN1/LAN2 port to your Ether-
net-equipped device.
4. Connect the power adapter to the DC IN
port into a wall outlet.
The figure above shows how to connect a ca-
ble modem to a home phoneline network. Fol-
low the same steps to connect any Ethernet
device such as a STB or PC, to a home phone-
line network.
After properly connected the LAN port, HPNA
port and the DC IN port, LED will be as:
PWR ON
LAN Link/Act ON
HPNA Link/Act ON (Green or Orange)
For more information on LEDs, see section
"LED Indicators on the Rear Panel"

- 5 -
TROUBLESHOOTING
The bridge has been designed to be a reliable
and easy to use connection device. Please refer
to the list below to aid in troubleshooting.
The Power (green PWR) LED is off.
Make sure the power adapter is properly
plugged into a live electrical outlet.
The LAN(Ethernet) LED is off.
Make sure the connection to LAN port is se-
cure.
The Ethernet device to which you are con-
nected should be powered on and properly
configured.
The HPNA Link/Act/Quality LED is off or red
Make sure the connection to HPNA port is
secure.
HPNA device to which you are connected
should be powered on and properly confi-
gured.
Make sure the quality of phoneline connector
and cable is good.

- 6 -
SPECIFICATIONS
Standards
IEEE 802.3 10BaseT Ethernet compliant
IEEE 802.3u 100BaseT Fast Ethernet com-
pliant
HomePNA 3.1 specifications compliant
Data Rates
HPNA: 192Mbps (36 - 68MHz)
Ethernet: 10/100 Mbps
Power Consumption
5V – 1A DC IN, Less than 3 watt
Certifications
CE, FCC Part 15
LEDs
Power
Ethernet Link/Activity
HPNA Link/Activity/Quality
Connectors
Two RJ-11, one for connecting with Ho-
mePNA device, and one for telephone by-
pass
Two RJ-45 for 10/100 Ethernet
Cables
Home Networking: standard home phone
wire
Fast Ethernet: CAT5 or better UTP

- 7 -
EC - Declaration of Conformity
for the following equipment:
ALL-HPNA3
HPNA3 over Phoneline Ethernet Bridge
The safety advice in the document accompanying the
p products shall be obeyed. The conformity to the above
directive is indicated by the CE sign on the device.
The A NET A -HPNA3 conforms to the Council Directives of EC EMC
2004/108/EC with CE marking requirement. This equipment meets the
the following conformance standards:
This equipment is intended to be operated in all countries.
This declaration is made by
A NET Deutschland GmbH
Maistr. 2
82110 Germering
Germering, 05.05.2012