Allnet ALL126AS3 User manual

ALL126AS3
VDSL2 100 Mbit Slave/Bridge Vectoring

ALL126AS3 USER’S MANUAL
1
Foreword: VDSL2 Router solution
Attention:
Be sure to read this manual carefully before using this product. Especially Legal Disclaimer, Statement
of Conditions and Safety Warnings.
ALLNET' ALL126AS3 is a management of the VDSL2 CPE router that leverages the extraordinary bandwidth promise of VDSL2
(max. 100Mbps symmetric) technology, the next step in the delivery of new high-speed Internet applications in commercial
environments. Quick, easy, economical to install and maintain, the ALL126AS3 works over existing copper wire infrastructure.
ALL126AS3 is a CPE
(Customer Premise Equipment) device. And compitable with the NV-802S(8Ports VDSL2 IP DSLAM) and NV-600L (VDSL2 CO
Router).
ALLNET ALL126AS3 will allow operators worldwide to compete with cable andsatellite operators by offering services such as HDTV,
VOD, videoconferencing, high speed Internet access and advanced voice services including VoIP, over a standard copper
telephone cable.ALLNET NV600A is seen by many operators as an ideal accompaniment to a FTTP rollout, where for instance fiber
optic is supplied direct to an apartment block and from there copper cable is used to supply residents with high-speed VDSL2.
Caution:
The ALL126AS3 is for indoor applications only. This product does not have waterproof protection, please do not use in outdoor
applications.

ALL126AS3 USER’S MANUAL
2
Safety Warnings
For your safety, be sure to read and follow all warning notices and instructions before using the device.
DO NOT open the device or unit. Opening or removing the cover may expose you to dangerous high voltage points or other
risks. ONLY qualified service personnel can service the device. Please contact your vendor for further information.
Use ONLY the dedicated power supply for your device. Connect the power to the right supply voltage (110V AC used for
North America and 230V AC used for Europe. ALL126AS3 supports 12 VDC power input).
Place connecting cables carefully so that no one will step on them or stumble over them. DO NOT allow anything to rest on
the power cord and do NOT locate the product where anyone can work on the power cord.
DO NOT install nor use your device during a thunderstorm. There may be a remote risk of electric shock from lightning.
DO NOT expose your device to dampness, dust or corrosive liquids.
DO NOT use this product near water, for example, in a wet basement or near a swimming pool.
Connect ONLY suitable accessories to the device.
Make sure to connect the cables to the correct ports.
DO NOT obstruct the device ventilation slots, as insufficient air flow may harm your device.
DO NOT place items on the device.
DO NOT use the device for outdoor applications directly, and make sure all the connections are indoors or have waterproof
protection place.
Be careful when unplugging the power, because it may produce sparks.
Keep the device and all its parts and accessories out of the reach of children.
Clean the device using a soft and dry cloth rather than liquid or atomizers. Power off the equipment before cleaning it.
This product is recyclable. Dispose of it properly.

ALL126AS3 USER’S MANUAL
3
Table of Contents
COPYRIGHT...............................................................................................................................................................FEHLER! TEXTMARKE NICHT DEFINIERT.
FOREWORD: VDSL2 ROUTER SOLUTION....................................................................................................................................................................................1
SAFETY WARNINGS........................................................................................................................................................................................................................2
1.1 CHECK LIST ..............................................................................................................................................................................................................................8
CHAPTER 2. INSTALLING THE ROUTER.......................................................................................................................................................................................9
2.1 HARDWARE INSTALLATION..........................................................................................................................................................................................................9
2.2 PRE-INSTALLATION REQUIREMENTS............................................................................................................................................................................................9
2.3 GENERAL RULES.....................................................................................................................................................................................................................10
2.4 CONNECTING THE ROUTER......................................................................................................................................................................................................11
2.5 CONNECTING THE RJ-11 /RJ-45 PORTS..................................................................................................................................................................................12
2.6 VDSL2APPLICATION...............................................................................................................................................................................................................13
CHAPTER 3. HARDWARE DESCRIPTION ...................................................................................................................................................................................15
3.1 FRONT PANEL .........................................................................................................................................................................................................................16
3.2 FRONT INDICATORS .................................................................................................................................................................................................................16
3.3 REAR PANEL ...........................................................................................................................................................................................................................17
CHAPTER 4. CONFIGURE THE ALL126AS3 VIA WEB BROWSER ............................................................................................................................................20
4.1 LOGIN.....................................................................................................................................................................................................................................21

ALL126AS3 USER’S MANUAL
4
4.1.1 Home.............................................................................................................................................................................................................................22
4.1.2 Quick Setup...................................................................................................................................................................................................................24
4.2 SELECT THE MENU LEVEL........................................................................................................................................................................................................30
4.3 SELECT “SYSTEM” ................................................................................................................................................................................................................31
4.3.1 Host Name Config.........................................................................................................................................................................................................32
4.3.2 System Time..................................................................................................................................................................................................................33
4.3.3 Administrator Settings ...................................................................................................................................................................................................35
4.3.4 Web Settings.................................................................................................................................................................................................................37
4.3.5 Software/Firmware Upgrade .........................................................................................................................................................................................38
4.3.6 Configuration Settings...................................................................................................................................................................................................39
4.3.7 System Log....................................................................................................................................................................................................................42
4.3.8 SSL Certificate...............................................................................................................................................................................................................46
4.3.9 Reset.............................................................................................................................................................................................................................47
4.4 SELECT “STATISTICS”...............................................................................................................................................................................................................48
4.4.1 LAN................................................................................................................................................................................................................................49
4.4.2 WAN ..............................................................................................................................................................................................................................51
4.5 SELECT “XDSL” ......................................................................................................................................................................................................................53
4.5.1 xDSL Status...................................................................................................................................................................................................................54
4.5.2 Vectoring Mode selection..............................................................................................................................................................................................56
4.6 SELECT “WAN” .......................................................................................................................................................................................................................57
4.6.1 WAN Mode Selection....................................................................................................................................................................................................59
4.6.2 Auto Detect Setting .......................................................................................................................................................................................................61
4.6.3 WAN Channel Config ....................................................................................................................................................................................................65

ALL126AS3 USER’S MANUAL
5
4.6.4 VLAN Channel confg.....................................................................................................................................................................................................70
4.6.5 WAN Setting..................................................................................................................................................................................................................73
4.6.6 WAN Status...................................................................................................................................................................................................................88
4.6.7 DNS...............................................................................................................................................................................................................................92
4.6.8 DDNS ............................................................................................................................................................................................................................94
4.6.9 OAM Configuration........................................................................................................................................................................................................96
4.7 SELECT “LAN” ......................................................................................................................................................................................................................100
4.7.1 LAN ARP List...............................................................................................................................................................................................................101
4.7.2 LAN Settings................................................................................................................................................................................................................102
4.7.3 UPnP Devices List.......................................................................................................................................................................................................112
4.7.4 LAN Switch Port Setting..............................................................................................................................................................................................113
4.7.5 LAN Port Status...........................................................................................................................................................................................................114
4.7.6 VLAN Settings.............................................................................................................................................................................................................115
4.8 SELECT “ROUTE”...................................................................................................................................................................................................................118
4.8.1 Static Routing ..............................................................................................................................................................................................................119
4.8.2 RIP Support.................................................................................................................................................................................................................122
4.8.3 Routing Table List........................................................................................................................................................................................................125
4.9 SELECT “FIREWALL”..............................................................................................................................................................................................................128
4.9.1 Firewall Setting............................................................................................................................................................................................................129
4.9.2 IPv6 Firewall Setting....................................................................................................................................................................................................130
4.9.3 Packet Filtering............................................................................................................................................................................................................132
4.9.4 URL Filtering................................................................................................................................................................................................................146
4.9.5 Parental Control...........................................................................................................................................................................................................148

ALL126AS3 USER’S MANUAL
6
4.9.6 Application Server Settings .........................................................................................................................................................................................150
4.9.7 Access Control List (ACL) ...........................................................................................................................................................................................152
4.10 NAT ...................................................................................................................................................................................................................................154
4.10.1 NAT Settings...........................................................................................................................................................................................................155
4.10.2 Virtual Server..........................................................................................................................................................................................................157
4.10.3 Port Triggering ........................................................................................................................................................................................................161
4.10.4 DMZ........................................................................................................................................................................................................................165
4.11 QOS...................................................................................................................................................................................................................................167
4.11.1 QoS Settings..............................................................................................................................................................................................................168
4.11.2 Queue Config.............................................................................................................................................................................................................170
4.11.3 Class Config ..............................................................................................................................................................................................................174
4.12 MULTICAST .........................................................................................................................................................................................................................180
4.12.1 Proxy Settings ...........................................................................................................................................................................................................181
4.12.2 Snooping Settings .....................................................................................................................................................................................................183
4.12.3 Advanced Settings.....................................................................................................................................................................................................185
4.13 IPSEC.................................................................................................................................................................................................................................187
4.13.1 Tunnel Mode..............................................................................................................................................................................................................188
4.14 IPV6...................................................................................................................................................................................................................................191
4.14.1 IPv6 Setting...............................................................................................................................................................................................................192
4.14.2 6RD Configuration.....................................................................................................................................................................................................194
4.14.3 DS-Lite Configuration................................................................................................................................................................................................196
4.15 DIAGNOSTICS......................................................................................................................................................................................................................199
4.15.1 Diagnostic Test Suite.................................................................................................................................................................................................200

ALL126AS3 USER’S MANUAL
7
APPENDIX A: CABLE REQUIREMENTS.....................................................................................................................................................................................203
APPENDIX B: PRODUCT SPECIFICATION ................................................................................................................................................................................206
APPENDIX C: ROUTER MODE SELECT....................................................................................................................................................................................209
APPENDIX D: NV-600L & ALL126AS3/W COMPATIBILITY TABLE ............................................................................................................................................212
APPENDIX E: TROUBLESHOOTING ..........................................................................................................................................................................................214
APPENDIX F: COMPLIANCE INFORMATION.............................................................................................................................................................................222
CE DECLARATION.......................................................................................................................................................................................................................226
GPL GENERAL PUBLIC LICENSE...............................................................................................................................................................................................227

ALL126AS3 USER’S MANUAL
8
Chapter 1. Unpacking Information
1.1 Check List
Carefully unpack the package and check its contents against the checklist.
Package Contents:
1 x Managed VDSL2 CPE
router
1 x QR code for user’s
manual hyperlink.
Accessory Kit : 1 x Ehternet Cable, 1 x Phone wire , 1 x
DC12V Power Adapter
Notes:
1. Please inform your dealer immediately for any missing or damaged parts. If possible, retain the carton including the
original packing materials. Use them to repack the unit in case there is a need to return for repair.
2. If the product has any issue, please contact your local vendor.
3. Do not use sub-standard power supply. Before connecting the power supply to the device, be sure to check
compliance with the specifications. The ALL126AS3 uses a DC12V/1A power supply.
4. The power supply included in the package is commercial-grade. Do not use in industrial-grade applications.
5. Please look for the QR code on the bottom of the product, the user can launch the QR code scanning program to
scan and download the user’s manual electronic format file. Above QR code icon is for reference.

ALL126AS3 USER’S MANUAL
9
Chapter 2. Installing the Router
2.1 Hardware Installation
This chapter describes how to install the router, and establish the network connections. The ALL126AS3 may be
installed on any level surface (e.g. a table or shelf). However, please take note of the following minimum site
requirements before you begin. The ALL126AS3 has 2 pre-installed rubber feet.
2.2 Pre-installation Requirements
Before you start the actual hardware installation, make sure you can provide the right operating environment, including
power requirements, sufficient physical space, and proximity to other network devices that are to be connected.
Verify the following installation requirements:
Power requirements: DC 12 V / 1A
The router should be located in a cool dry place, with at least 10cm/4in of space at the front and back for
ventilation.
Place the router away from direct sunlight, heat sources, or areas with a high amount of electromagnetic
interference.
Check if the network cables and connectors needed for installation are available.
Do not install phone lines strapped together with AC power lines, or telephone office line with voice signal.
Avoid installing this device with radio amplifying stations nearby or transformer stations nearby.
Please note that the voice spectrum allowed by the ALL126AS3 internal splitter is 0 KHz ~ 120 KHz.

ALL126AS3 USER’S MANUAL
10
2.3 General Rules
Before making any connections to the router, please note the following rules:
Ethernet Port (RJ-45)
All network connections to the router Ethernet port must be made using Category 5 UTP/STP or above for
100 Mbps, Category 3, 4 UTP for 10Mbps.
No more than 100 meters of cabling may be use between the MUX or HUB and an end node.
VDSL2 Port (RJ-11)
All network connections to the RJ-11port must use 24~26 gauge with twisted pair phone wiring.
We do not recommend the use of the telephone line 28 gauge or above.
The RJ-11 connectors have six positions, two of which are wired. The router uses the center two pins. The
pin out assignment for these connectors is presented below.
Please note that the line port is no polarity, therefore user can reverse the two wires of the phone cable
when installed. RJ-11 Pin out Assignments
Pin#
MNEMONIC
FUNCTION
1
NC
Unused
2
NC
Unused
3
DSL
Used
4
DSL
Used
5
NC
Unused
6
NC
Unused_

ALL126AS3 USER’S MANUAL
11
2.4 Connecting the Router
The router has four Ethernet ports which support connection to Ethernet operation. The devices attached to these
ports must support auto-negotiation /10Base-T / 100Base-TX / 1000Base-TX unless they will always operate at half
duplex. Use any of the Ethernet ports to connect devices such as Monitor systems, Servers, Switches, bridges or
routers.
Notes:
1. The (RJ11/Terminal Block) Line port is used to connect the telephone that is connected to VDSL2 CO and CPE
router (Point-to-point solution).
2. The Slave device (CPE) must be connected to the Master device (CO) through the telephone wire. The Slave
cannot be connected to another Slave, and the Master cannot be connected to another Master.

ALL126AS3 USER’S MANUAL
12
2.5 Connecting the RJ-11 / RJ-45 Ports
The line port has 2 connectors: RJ-11 and terminal block. It is used to connect with NV-600L(CO) using a single pair phone
cable to ALL126AS3(CPE) bridge side (point to point solution). Take note that ALL126AS3 line port cannot be used at the same
time. Either RJ-11 port is connected or terminal block is connected using a straight connection (Figure 2.4) or cross-over
connection(Figure 2.5)
When inserting a RJ-11 plug, make sure the tab on the plug
clicks into position to ensure that it is properly seated.
Do not plug a RJ-11 phone jack connector into the Ethernet
port (RJ-45 port). This may damage the router. Instead, use
only twisted-pair cables with RJ-45 connectors that conform
to Ethernet standard.
Figure 2.1ALL126AS3 line ports straight connection
Notes:
1. Be sure each twisted-pair cable (RJ-45 ethernet cable) does not exceed 100 meters (333 feet).
2. We advise using Category 5~7 UTP/STP cables for Cable bridge or Router connections to avoid any confusion
or inconvenience in the future when you attached to high bandwidth devices.
3. RJ-11 (VDSL2 Line port) use 24 ~ 26 gauge with twisted pair phone wiring, we do not recommend 28 gauge or
above.
4. Be sure phone wire has been installed before the ALL126AS3 boot.

ALL126AS3 USER’S MANUAL
13
2.6 VDSL2 Application
The router’s line port supports 100Mbps/0.3km for data service across existing phone wiring. It is easy-to-use which do not require
installation of additional wiring. Every modular phone jack in the home can become a port on the LAN. Networking devices can be
installed on a single telephone wire that can installation within suitable distance (depends on speed)

ALL126AS3 USER’S MANUAL
14
2.6.1 Connect the NV-600L and the ALL126AS3 to the Line
The objective for VDSL2 is to pass high speed data over a twisted pair cable. In the setup, connect NV-600L to ALL126AS3
through phone wire(24~26 AWG) or line simulator or any other hardware representation of a cable network, with or without noise
injection and crosstalk simulations.
2.6.2 Connect the NV-600L and the ALL126AS3 to LAN Devices
In the setup, usually an Ethernet tester serves as a representation of the LAN side as well as a representation of the WAN side.
2.6.3 Run Demos and Tests
The Ethernet tester may send data downstream as well as upstream. It also receives the data in order to check the integrity of
the data transmission. Different data rates can be tested under different line conditions.

ALL126AS3 USER’S MANUAL
15
Chapter 3. Hardware Description
This section describes the important parts of the vdsl2 router. It features the front panel and rear panel.
ALL126AS3 Outward

ALL126AS3 USER’S MANUAL
16
3.1 Front Panel
The figure shows the front panel. (Figure 3.1)
Figure 3.1 Front Panel(ALL126AS3)
3.2 Front Indicators
The router has Six LED indicators. The following Table shows the description. (Table 3-1)
Table 3-1 LED Indicators Description and Operation
LED
Color
Status
Descriptions
PWR
(Power LED)
Green
On(Steady)
Lights to indicate that the VDSL2 router had power
Off
The device is not ready or has malfunctioned.
E1 ~ E4
(Ethernet LED)
Green
On(Steady)
The device has a good Ethernet connection.
Blinking
The device is sending or receiving data.
Off
The LAN is not connected or has malfunctioned.
LINK
(VDSL2 LED)
Green
On(Steady)
The Internet or network connection is up.
Fast Blinking
The device is sending or receiving data.
Slow Blinking
The Internet or network connection is down.

ALL126AS3 USER’S MANUAL
17
Note:
It is normal for the connection between two Routers to take up to 3 minutes, due to NV-600L/A to establish a link mechanism in
auto-negotiation, with detects and calculates CO and CPE both PBO and PSD level, noise levels and other arguments for getting a
better connection.
3.3 Rear Panel
The following figure shows the rear panel. (Figure 3.2)
Figure 3.2Rear Panel

ALL126AS3 USER’S MANUAL
18
And the table shows the description. (Table 3-2)
Table 3-2 Description of the router rear connectors
Connectors
Type
Description
Reset
Tact switch Button
The reset buttons allows users to reboot the VDSL2 or load the default
settings.
Press and hold for 1-5 seconds: Reboot the VDSL2 Router
Press over 5 seconds: Load the default settings
Power
DC Power Jack
External Power Adapter: Input: AC 85~240Volts/50~60Hz
Output: DC 12V/1A
Line
RJ-11/Terminal Block
For connecting to a VDSL2 device. (Do not use RJ11 and Terminal
Block at the same time.)
Phone
RJ-11
For connecting to the POTS equipment or ISDN router
Gigabit Ethernet
(E1-E4)
RJ-45
For connecting to an Ethernet equipped device.
Link (WAN)
RJ-11/Terminal Block
For connecting a VDSL2 bridge. (Do not use RJ11 and Terminal Block
at the same time.)
CONSOLE
RS-232
For connecting a PC with RS-232 serial port over a D-SUB Cable

ALL126AS3 USER’S MANUAL
19
Before user installed power and device, please read and follow these essentials:
Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the
wires are perpendicular at the intersection point.
Note:
Do not run signal or communications wiring and power wiring through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
You can use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb
is that wiring sharing similar electrical characteristics can be bundled together.
You should separate input wiring from output wiring.
We recommend that you mark all equipment in the wiring system.