AllSportSystems SUPERBAY Series User manual

[email protected] 877-847-1280 www.allsportsystems.com
SETUP GUIDE FOR THE
SUPERBAY™
Golf Simulator Screen Systems

AllSportSystems, Inc.© 2020.

Table of Contents
ITEMS YOU WILL NEED 4
Tools/Equipment 4
Building Materials Not Included 4
MEASURING AND CUTTING EMT POLES 5
Width And Height Poles 5
Depth Poles 5
ITEMS PROVIDED BY ALLSPORTSYSTEMS 6
BUILDING THE ENCLOSURE FRAME 7
Frame Diagram 7
Step 1 - Add Extender Poles 8
Low Ceilings (See Appendix B) 8
Step 2 - Build Bottom 9
Step 3 - Add Rear Height Poles 10
Step 4 - Insert Rear Top Width Pole 11
Step 5 - Build Top Sides 12
Step 6 - Install Front Height Poles 13
Step 7 - Install Screen Pole 14
Step 8 - Install SkyRailPLUS™ Cage Mount (optional add-on) 15
Step 9 - Install Front Width Pole 17
Step 10 - Position Screen Pole 18
Step 11 - Check All Connections and Verify Dimensions 19
Step 12 - Install BlackOut™ Pole Sleeves 20
INSTALL NETTING 21
Step 13 - Place Netting Over Enclosure 21
Step 14 - Tighten Netting 22
Step 15 - Handling Excess Netting 22
Step 16 - Install Baffle Net 23
PROJECTION SCREEN INSTALLATION 24
Step 17 - Install SideRite™ tension kit 24
Step 18 - Before hanging the screen: 26
Step 19 - Hang Screen 27
Step 20 - Attach Screen to SideRite™ tensioning kit 28
Step 21 - Install ShotDefender™ cabling 30
Page 2 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
BLACKOUT™ - What’s Included… 31
Step 22 - Identify A, B and C panels… 32
Step 23 - Install Cascading A & B Panels 33
Step 24 - Install Cascading C Panel 34
Step 25 - Install Ridge Caps 35
Step 26 - Install Rear Panel 36
SAFETY PRECAUTIONS 37
APPENDIX A - SideRite™ and ShotDefender™ Cable Assembly 38
Step 1 - Attach Cable to Turnbuckle 39
Step 2 - Add eye and trim cable to proper length 40
APPENDIX B - BUILDING THE FRAME (For Low Ceilings) 41
Step 1 - Top Rear Width Pole 42
Step 2 - Two Rear Height Poles 43
Step 3 - Stand Rear Height Poles 44
Step 4 - Add Bottom Rear Width Pole 45
Step 5 - Add Bottom Depth Poles 46
Step 6 - Add Top Depth Poles and Screen Pole 47
Step 7 - Add Front Height Poles 48
Page 3 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
ITEMS YOU WILL NEED
For safety we recommend at least two persons to be on hand to assemble your hitting enclosure.
Tools/Equipment
● Six foot step ladder
● Screwdriver
● Hacksaw/Tubing Cutter (or ask the store to cut the EMT poles for you)
● Scissors/Utility Knife
● Measuring Tape
● Pencil
Building Materials Not Included
The following items are not included and must be obtained locally.
●¼ inch chain
Chain needed for the ShotDefender™, cut to width of your enclosure minus 9 inches.
●Metal EMT Poles
1” diameter, 10’ long EMT conduit poles from any major local hardware store. For
quantity and lengths needed see chart on following page.
Metallic EMT 10-ft Conduit
(1” diameter)
SkyBay™: If you ordered the SkyBay™ please see a separate installation
guide. All Installation guides can be found on our website
www.allsportsystems.com, see ‘Setup Guides’ link at the bottom of any page
or use the link below…
https://www.allsportsystems.com/setupguides.php
Page 4 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
MEASURING AND CUTTING EMT POLES
To calculate total poles needed  add the number of poles needed from Width and Height chart and
poles needed from the Depth chart.
Width And Height Poles
Number of poles needed varies according to width of enclosure as follows:
Hitting Bay Size
Number of
10’ long poles
Cut poles as follows:
SuperBay™
10W x 9H
8 poles
Height: 4 poles cut to 8’9” ea.
Width: 4 poles cut to 9’9” ea.
Extender: none needed
SuperBay™
12W X 9H
9 poles
Height: 4 poles cut to 8’9” ea.
Width: 4 poles at 10’0” (no cuts needed)
Extender: 1 pole cut into 4 poles 1’9” ea.
SuperBay™
14W x 9H
10 poles
Height: 4 poles cut to 8’9” ea.
Width: 4 poles at 10’0” (no cuts needed)
Extender: 2 poles cut into 4 poles 3’9” ea.
SuperBay™
16W x 9H
12 poles
Height: 4 poles cut to 8’9” ea.
Width: 4 poles at 10’0” (no cuts needed)
Extender: 4 poles cut to 5’9” ea.
Depth Poles
Number of depth poles needed varies only based on depth of enclosure as follows:
Enclosure Depth
Number of
10’ long poles
Cut Poles as follows
5’ deep
2 poles
cut into 4 poles 4’9” ea.
10’ deep
4 poles
cut each pole to 9’9” ea.
Custom Orders where
depth is between
6’ to 10’ deep
4 poles
cut to depth of enclosure minus 3”
i.e. for 8’ deep enclosure cut each pole to 7’9”
Note: Each corner bracket adds approximately 1.5” to the size of your enclosure. Therefore, once
poles and brackets are assembled an additional 3” will be added to the finished width, height and
depth of your enclosure. Therefore, all poles are cut 3” shorter than the finished height, width, or
depth of the enclosure. If you have ordered a  custom  sized enclosure make note of this factor
when cutting your poles  .
Page 5 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
ITEMS PROVIDED BY ALLSPORTSYSTEMS
ITEM
QTY
DESCRIPTION
Cable ties
6 ea
3-Way Corners
2 ea
T-Connectors
2 ea
L-Corners
4 ea
Couplers
1 ea
Enclosure Netting
1 ea
Baffle Back Stop Net, single net same size as screen
1 ea
Impact Screen
Multiple
pieces
BlackOut™ Wrapper - see BLACKOUT™ - What’s Included…
1 ea
ShotDefender™ Valance (made from Blackout™)
see ShotDefender™ Safety Guard
3 ea
Stainless Steel Cables & Turnbuckles:
1 ea for ShotDefender™
2 ea for SideRite™
See APPENDIX A
1 ea
OPTIONAL ADD-ON: SkyRailPLUS™ Cage Mount, see Step 8 -
Install SkyRailPLUS™ Cage Mount
Page 6 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
BUILDING THE ENCLOSURE FRAME
Frame Diagram
Refer to this diagram often to identify connectors and poles needed for the step by step instructions on
the following pages. Note that the 10 Wide SuperBay™ does not use couplers to extend the length of
the width poles.
2 ea L-Corners
2 ea T-Connectors
6 ea 3-Way Corners
4 ea Couplers
(SuperBay™ only)
Note: Each corner bracket adds approximately 1.5” to the size of your enclosure. Therefore, once poles and
brackets are assembled an additional 3” will be added to the finished width, height and depth of your
enclosure. Therefore, all poles are cut 3” shorter than the finished height, width, or depth of the enclosure. If
you have ordered a  custom  sized enclosure make note of this factor when cutting your poles  .
Page 7 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 1 - Add Extender Poles
Note: Applies only to SuperBays™ greater than 10 feet wide.
● Add Couplers and Extender poles to each of the four Width poles.
Low Ceilings (See Appendix B)
If your hitting bay will be closer than 6” to the ceiling see APPENDIX B -
BUILDING THE FRAME (For Low Ceiling) for modified instructions of frame
assembly.
Page 8 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 2 - Build Bottom
●Place the bottom rear width pole in the location where you desire the rear of your
hitting bay to be located. SuperBay™ enclosures should have extender poles already
attached to the width pole from the previous step. Tip: Always position the eye bolts
facing down and toward the inside of the enclosure.
●Add two 3-Way corner connectors to each end of the above width pole.
● Insert two Bottom Depth poles into the bottom rear 3-Way corners, one on each side.
● Add two L-Corner brackets, to the front end of the bottom depth poles, pointing
upward.
● This establishes the bottom of your frame.
●Verify Dimensions: Use a tape measure to verify correct width and depth dimensions
and then tighten all connectors. You may need to back the poles slightly out of the
connectors to reach the correct dimension.
Page 9 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 3 - Add Rear Height Poles
● Place 3-Way corner connectors on top of two height poles.
● Insert Height poles into each rear 3-Way corner connectors.
●Verify Dimensions: Use a tape measure to verify correct height and then tighten all
connectors. You may need to back the poles slightly out of the connectors to reach
the correct dimension.
Page 10 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 4 - Insert Rear Top Width Pole
● With an assistant, and a step ladder, insert the rear top width pole. SuperBay™ enclosures
should have extender poles already attached to the width pole from step two.
●Verify Dimensions: Use a tape measure to verify correct width dimension and then
tighten connectors. You may need to back the pole slightly out of the connectors to
reach the correct dimension.
Page 11 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 5 - Build Top Sides
● Insert the Top Depth poles into respective Top Rear 3-Way connectors and tighten.
● Slide the T-connectors onto the Right and Left Top Depth poles, leaving the T connectors
loose (position the T-connectors so that the eye bolts face the ground).
Page 12 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 6 - Install Front Height Poles
● Insert two three-way corners to one end of the last two height poles
● Install the front height poles by inserting the bottom into the front L Corner brackets and the top
three-way corner into the end of the top depth poles.
Page 13 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 7 - Install Screen Pole
● With an assistant, insert a width pole into the T-connectors. SuperBay™ enclosures should
have extender poles already attached to the width pole from step two. You may need to
carefully expand the top of the enclosure to fit the Screen pole into the T-connectors.
● Temporarily slide the Screen pole to the back of the enclosure as far as you can. This will
make installing the final front width pole easier.
Page 14 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 8 - Install SkyRailPLUS™ Cage Mount (optional add-on)
IMPORTANT: Before installing the SkyRailPLUS™ be sure that the top is installed correctly for
positioning your projector the proper distance from the screen. See the SkyRailPlus™ ASSEMBLY
GUIDE for more details. All Installation guides can be found on our website
www.allsportsystems.com, see ‘Setup Guides’ link at the bottom of any page or use the link below…
https://www.allsportsystems.com/setupguides.php
The SkyRailPLUS™ mount is installed at the same time as the Front Width
Pole...
Loosen bolts that hold HOOK onto the
EXTENDERS of the SkyRailPlus™. This will
allow the HOOKS to slide up to 2” making it
easier to line HOOKS up with the Screen pole.
Thread TOP FRONT Width pole through holes
on SkyRailPLUS™.
Install the TOP FRONT Width pole. You may
need to carefully expand the top of the
enclosure to fit the pole into its connectors. The
Screen pole should be pushed as far back as
possible to make installing this last pole easier.
Verify Dimensions: Use a tape measure to
verify correct width dimension and then tighten
connectors. You may need to back the poles
slightly out of the connectors to reach the
correct width dimension.
Page 15 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Rotate SkyRailPLUS™ into position lining up the hooks with the Screen pole which can now slide
forward approximately 12 inches from the rear of the enclosure.
NOTE: The HOOKS on the SkyRailPlus™ will slide up to 2” so that the Screen pole can be
positioned properly.
Verify Dimensions: Use a tape measure to verify the correct dimension. You may need to back
the poles slightly out of the connectors to reach the correct width dimension. Tighten connectors on
the Screen pole and tighten bolts on HOOKS of SkyRailPlus™.
Page 16 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 9 - Install Front Width Pole
● Insert the TOP FRONT Width pole. SuperBay™ enclosures should have extender poles
already attached to the width pole from step two. You may need to carefully expand the top of
the enclosure to fit the top front width pole into its connectors.
● The Screen pole should be pushed temporarily as far back as possible to make inserting this
last pole easier.
●Verify Dimensions: Use a tape measure to verify correct width dimension and then tighten
connectors on front width pole. You may need to back the poles slightly out of the connectors
to reach the correct width dimension.
Page 17 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 10 - Position Screen Pole
● Now slide the Screen Pole forward until it sits approximately 12” from the back of the enclosure
and tighten the T-Connectors.
Page 18 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 11 - Check All Connections and Verify Dimensions
● Proper positions of the poles and brackets for the SuperBay™ frame are shown below.
●Note: The 10 Wide SuperBay™ does not need extender poles.
● The screen pole should be 12” from the back of the enclosure.
● Before proceeding, reverify that all connectors are tight and outside dimensions are correct.
Shown below is a 12 Wide SuperBay™, 5’ deep.
Shown here SuperBay™ 12Wx9Hx5D
With SkyRailPLUS™ Mounted
Screen Pole 12” from back
CHECK ALL CONNECTIONS TO BE SURE THEY ARE TIGHTENED DOWN
AND VERIFY OUTSIDE DIMENSIONS
SuperBay™ - 10Wx9Hx5D or 12Wx9Hx5D or 14Wx9Hx5D or 16Wx9Hx5D
IF YOU HAVE PURCHASED THE SKYRAILPLUS™ CAGE MOUNT IT SHOULD NOW BE MOUNTED ON
THE CAGE, PRIOR TO THE INSTALLATION OF NETTING AND BLACKOUT™ WRAPPER
Page 19 of 48 Return to Table of Contents February 3, 2020

AllSportSystems, Inc.© 2020.
Step 12 - Install BlackOut™ Pole Sleeves
NOTE: In rare cases you may not receive the BlackOut Wrapper Kit at the same time as your screen and
enclosure. In those cases you can continue with the rest of the installation and add the pole sleeves later
once they arrive. This will allow you to begin using your enclosure until the BlackOut™ kit arrives.
Install pole sleeves..
● Install 4 ea pole sleeves on the top and bottom left/right depth poles.
● Pole sleeves wrap around the pole and velcros closed.
For a complete list of what’s included in the BlackOut™ Kit see BLACKOUT™ - What’s Included…
Page 20 of 48 Return to Table of Contents February 3, 2020