ALORAIR Storm SLGR 850C User manual

Add: 4240 Latham Street, Suite D, Riverside, CA 92501
Tel: [phone]
E-mail: [e-mail]
Alorair Solutions INC.
StormSLGR850C

[e-mail]
888-990-7469
How the SLGR 850C Works
9
12
Model Number: Storm SLGR 850C
115V/60Hz
circuit protector:15 Amp
220

Storm SLGR 850C
Air inlet
Air outlet
Storm SLGR 850C
HowtheStorm SLGR 850C works

LCD Display Instructions
The machine displays when it is not
working. (Power off state but have
electricity)
PURGE
PURGE
PURGE
PURGE
PURGE
PURGE
1. When the machine is powered on but not working:
Boot display: The LOGO interface
will disappear after 2 seconds. Enter
the following interface
2. Main interface display of dehumidification state:
The following information is displayed when the machine is working:
Refers to the working time, which is defined as the time from
starting up to shutting down,including the defrost time during
the period, and the standby time after the humidity. The
submenu has a reset function. If not, the working time shall
be accumulated.
Total time 9999 hours, the largest cumulative to the largest
automatically reset after restart, and display units for hours.
(round off).
000 JOB HRS:
(after power on, the buzzer makes a sound)
000 LIFE HRS:
Refers to the total working time, i.e. the total working time (hours), which is in hours.(press the mode key +
select the confirmation key, and the total working time will be cleaned after 3 seconds.
IN/OUT 00℉ 00% 00 gr / lb:
Indicates the temperature, humidity and moisture content of the air inlet and outlet
{GPP - grain per pound (gr/lb)}.
Indicates set humidity.
Set 00%:
If the main interface does not operate for 10 minutes, the screen will go out.Press any key to
wake up.
Other icons light up or flicker when opened
The total working time is the accumulation of each working time (hours) in hours. (Press the
mode key + select to confirmation key, and the total working time will be cleaned after 3 seconds.
3.Dehumidification status submenu interface display
3.1
Device name displayed on the screen:
You can change the device name on the APP
application
BTID=Unique identifier for Hotspot broadcasting
“Indicates”:Do I need to clear out this time?",
press ">"if you need to clear. When the operation
is completed, the working time of the main
interface and the working time of this interface
will be reset and started to be instant again.
After accumulation (9999), clean up and round.
3.2
3.3
“Coil Temp 000℃ ”: Used to display the current
temperature of the coil.When it is below zero,
the "-" symbol is displayed in front. "-" is not
required on zero.
54

3.4
Wifi hotspot: factory setting is "0FF",
press > to enable wifi hotspot and switch
ON/OFF.The device can transmit data and receive
APP commands.The icon flickers when connected
on the main interface. After successful connection,
the icon displays normally.
3.5.1
The power down time is adjusted according to">"
and the power down time increases from 3 to 20
minutes (3-5-10-15-20), which is the so-called
stop time of the fan after shutdown, in order to
better drain the water.Factory set for 3 minutes.
(the other state of the fan is still 15 seconds.)
3.5.2
The screen displays when you press shut
down:
Indicates: the fan is closed after a few minutes,
and the standby page UNIT OFF is displayed after
the fan is closed.
3.6 3.7
“Temp Units ℉/℃”：Used for temperature scale
switching.Press the ">" button to switch ℉/℃,
after switch symbol of corresponding parts is also
changing.
“MOISTURE CONTENT UNITS”：It is used to
switch the unit of GPP value with moisture
content. Press > to switch the Ib or Kg, after
switch symbol of corresponding parts is also
changing.
3.8
"Humidistat Setpoint 00%":Used for setting dehumidification
mode humidity.Press ">" to set the humidity. The adjustment
range of humidity setting is between 25 and 80%.
Each key rises or falls 5%, which can be recycled.
When the setting is completed,do not operate for 5 seconds
and begin to take effect.(Otherwise, the compressor will be
shut down immediately after it is below ambient humidity at
the time of setting.) Humidity below 25 percents "CO" mode
recyclable.The main interface displays the set parameters.
4. Main interface frosting status display:
The machine will display this after defrost when running
When the machine is running normally, “Deffrost
SHUTDOWN IN 06:00” will occurs in the
interface after defrosting. It’s defrost countdown
use seconds as units. This screen displays only
3 seconds. Displays the previous interface and
status after restoration.If it is the home screen,
the frost icon will flash.
When the user is operating in the submenu, the
machine is in the frosting state.At this point, the
frosting interface displays 3 seconds, and returns
to the submenu program in the background
countdown.When the user returns to the main
interface without any operation, the frosting state
is displayed inthe main interface in the way of
icon flicker.
5. Compressor on waiting interface display
Compressor protection time not shown:
“Compressor ready IN 03:00” indicates : That the
interface will be displayed when the compression is
in a protected state. (including power-on and shutdown,
the humidity rises immediately after the arrival of L0
HI, and the shutdown resumesimmediately after the
emergence of L0 HI).Displays the countdown in seconds.If the
above situation does not occur within 3 minutes, it is not
shown.
76

6. Water Pump working interface display
Compressor protection time not shown:
“Pump working countdown”: indicates: No matter in which
working state and interface, as long as the pump works, this
interface appears and counts down to 28 seconds.However,
the interface only displays the previous working status and
interface after 3 seconds.For example, after 3 seconds, there
is a drainage icon on the main interface and it
will flash until the drainage is finished.
7.Interface display in case of failure
Machine running time fault display:
Make fault judgment and take corresponding actions after starting
up. Regardless of the state, the fault is executed first and the fault
code is displayed on the interface. If there is a fault in the
sub-menu operation, immediately return to this interface display
fault (including defrosting state). (the fault is judged when the pump
works, and the fault is displayed as usual, but the pump needs to
complete the water pumping this time). Multiple faults can be
displayed at the same time.
Description of fault display:
Humidity sensor fault: when the humidity sensor unit fault or signal can not be transmitted, the fault is
judged to be E1. The machine is out of operation (power on again after troubleshooting). Pump button
can operate.
Ambient temperature T≤2: When the sensor continuously detects the ambient temperature of inlet air
T=2 degrees for 600 seconds, the fault is judged to be LO and the whole machine is stopped. Other values,
corresponding to the temperature region operation. (recoverable). At this time, the interface cannot
be operated. The pump button can be operated.
Ambient temperature T≥45: When the sensor continuously detects the inlet air environment
temperature T=45 degrees for 15 seconds, the fault is judged to be HI and the whole machine is stopped.
Other values, corresponding to the temperature region operation. (recoverable). At this time, the interface
cannot be operated. The pump button can be operated.
98

HI Error
E5 Error Code
E4Error Code
f
11
10

13
12