Alpha RE101 Series Manual

PIONEER REMOTE INSTRUCTIONS p1
2345678
08
M
16
2345678
9
10 11 12 13 14 15 16
184 0
Su
184 0
234
Su
K1
K2
K3
K1
K2
K3
K1
K2
K3
K1
K2
K3
K1
K2
K3
UP
STOP
DOWN
LIGHT
UP
STOP
DOWN
LIGHT
UP
STOP
DOWN
UP
STOP
DOWN
UP
STOP
DOWN
UP
STOP
DOWN
UP
STOP
DOWN
Channel
Switc Buttonh
learnin uttong b
•Currency 2mA:≤1
•Code olling Code: R
•Frequency 33.92MHz: 4
•Powe V Model: CR2430r: 3
•Protectio ndex: I 20n I P
•Working Temperature: -10 to +60 LCD remote)℃℃(
•Working Temperature: -20 to +60℃℃(Non CD remote)- L
Pres p and Down buttons simultaneously once,then short press Stop button once.s U
0.42 remotechannel
Shor p esstr the Channel Switch
button to select a channel
(from 1 to 4), once selected,
the corresponding light will shine.
Press UP and DOWN buttons
simultaneously once.
Then short press the Stop button,now
the code of the selected channellearning
is channels to learn codesuccessful. therO
in the way.same
The figure on upper left corner of the showsscreen
the current press K1/K3 to choosechannel. Short
any from 1 to 8.channel
Choose one then press UP and DOWNchannel,
buttons once.simultaneously
Then short press the STOP once, now thebutton
code learning of current channel is successful.
0.L3 CD multi-channel remote (take RE103-8C as an example)
Instruction guide for RE101, RE102, RE103 series remotes
1. PRODUCT APPEARANCE
2. TECHNICAL DATA
3. CODE LEARNING
ALPHA SUPPORT PHONE [phone]
RE101 single channel RE102 4 channel RE103 4C 4 channel RE103 8C 8 channel
RE10 channel RE10 RE103 4 4 channel timer3 16C 16 3 1T single channel timer T
01. single channel remote

MS
Pr ss K1 K3 bu ton o se ct a channe , the the corr ponding motor can be c ntrolled by the remote through UP/STOP/ DOWN button.e / t t le l n es o
Short press K2 button to choose group control r Single controlo
Long pr ss 2 f r 2 t en ere K o s o t Group Control
mode, the current channel on the upper left
corner of the screen will shine.
Long pr ss 2 f r 2 t en ere K o s o t Group Control
mode, the current channel on the upper left
corner of the screen will shine.
Short press K1/K t ch ose channels into3o o
Short press K1/K channels3 to choose out
yur roup,o g for example channel 8
as the picture shows.
yur roup,o g for example channel 6
as the picture shows.
Sh rot cr p ess K2 to onfirm, same method
for elsth ot er hann .ehc Press UP/STOP/DOWN butto tno
ex t t e s tting.ih e
Short press K2 to confirm, same formethod
the other channels.
Press UP/STOP/DOWN butto tno
ex t t e s tting.ih e
Note: inwhether or mode, the current channel is always selected.
MS
01. Tim ettinge S
Press K1 button to enter hour setting
page, now the hour figure will shine.
Press button to adjustUP/DOWN
the hour figure.
Once the hour settin i f nished, pressgsi
K1 again to adjust minute t e inute,h m
figure will shine P ess UP/DOWN.r
button to adjus t e igure.th f
Once the minute setting is finished ress, p
K1 agai o adjust weekday, the weekdayn t
figure will shine ress UP/DOWN. P
button to adjust th eekday.e w
After setting, press STOP button to
exit and go back to the page.initial
In the initial page, press K2 to enter timing setting page, there is a timing clock on the upper left corner.
You can respectively set 8 opening time points and 8 closing time points, in total 16 points.
Press K2 to cycle among 16 time points. Press K3 to choose the output channels which you want (single channel or 4 channels)
02.Timin ettingg S (se ifferent time points to make the motor close or open)t d
18
~
Press K2 t nter timing settin ageo e g p Press K3 to choose you wante hanneld c
(single channel o hannels).r 4 c
PressK1tose time(inthesamet
way Time Setting above).of
Press K2 again to selec ne pointt o
among 16 timing points
4. SINGLE CONTROL
5. GROUP CONTROL (4 CHANNEL )REMOTE
6. GROUP CONTROL (LCD )REMOTE
7. DELETE GROUP CONTROL
8. RE103-T
PIONEER REMOTE INSTRUCTIONS p2
Instruction guide for RE101, RE102, RE103 series remotes
ALPHA SUPPORT PHONE [phone]
Short press the Channel Switch button to select
different channels (from 1 to 4), once selected,
corresponding light will shine.
Note: If all of the 4 lights are on, it means the remote
is in Group Control state.

PIONEER REMOTE INSTRUCTIONS p3
Instruction guide for RE101, RE102, RE103 series remotes
Once one time poin is se , ress K2 againttp
to select other time points to set time.
Press K2 to enter timing
setting page.
Press K2 to enter timing
setting page.
Press K2 to enter timing
setting page.
Press K2 again to select one
point that need to be closed.
Press K2 again to select one
point among 16 timing points.
Press K2 again to select one
point that needs to be closed.
Press K3 until above display appears,
which means the point has closed.
Press K3 again to retrieve this point.
Press K3 to enter time setting page,
then set the time points in the same
way as above time setting.
Press K3 once to delete the point.
Press K3 again to retrieve this point.
After setting, press STOP
button to exit and go back
to the initial page.
Once one time point is set,
press K2 again to select other
time points to set time.
After setting, press STOP
button to exit and go back
to the initial page.
Press STOP button to exit the setting.
03. Clos Fe Timing unction
01. Time Setting
0.3Close Timing Function
04. Stopwatch Function
In the same way as RE103-4T Time Setting.
In the initial page, press K2 to enter timing setting page, there is a timing clock on the upper left corner. You can respectively set 8 opening time points
and 8 closing time points, in total 16 points. Press K2 to cycle among 16 time points.
02. Timin ettingg S (se ifferent time points to make the motor to close or open)t d
18
~
If you want to exi rom stopwatch page,t f
press K3 again t o back to initial page.o g
In the initial page, pres K to enters3
Stopwat h age.cp
9. RE103-IT
!Note:
The must enter into timing setting page if you want to set timingremote
points (there is a timing clock on the upper left), otherwise, the setting is
invalid. If there is no timing clock on the upper left, hold STOP button and
press k2 within 10 seconds, then the timing clock will be there.
You'd better not press 's buttons too long. Each pressing is aboutremote
0.5 and the pressingssinterval is about 1 .
The will stop working if the battery is in low power. Please replaceremote
the battery in this case.
ALPHA SUPPORT PHONE [phone]