Altronix T2RM7CK1 User manual

Access & Power Integration
T2RM7CK1
8 Door Kit with Fused Outputs
Accommodates one (1) Intelligent Dual Reader Controller and
three (3) Dual Reader Interface Modules.
Fully assembled kit includes:
- Trove2R rack enclosure with TM2R Altronix/Mercury backplane
- One (1) eFlow104NB - Power Supply/Charger
- One (1) ACMS8 - Dual Input Fused Access Power Controller
- One (1) PDS8 - Dual Input Fused Power Distribution Module
- One (1) VR6 - Voltage Regulator
- Wire harnesses and management
T2RM7CK1D
8 Door Kit with PTC Outputs
Accommodates one (1) Intelligent Dual Reader Controller and
three (3) Dual Reader Interface Modules.
Fully assembled kit includes:
- Trove2R rack enclosure with TM2R Altronix/Mercury backplane
- One (1) eFlow104NB - Power Supply/Charger
- One (1) ACMS8CB - Dual Input PTC Access Power Controller
- One (1) PDS8CB - Dual Input PTC Power Distribution Module
- One (1) VR6 - Voltage Regulator
- Wire harnesses and management
Rev. 072423
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners. More than just power.™
Installation Guide
Altronix/Mercury Wired Rack Kits
Models Include:
All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

- 2 - T2RM7CK1(D) Installation Guide
Overview:
Altronix Trove Mercury rack kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/charger
and sub-assemblies. All kits accommodate a variety of Mercury modules for up to eight doors in a single enclosure.
Configuration Chart:
Altronix
Model
Number
120VAC 60Hz Input Current (A) Power Supply Board Input Fuse Rating Power Supply Board Battery Fuse Rating
Nominal DC
Output Voltage
Maximum Supply
Current for Main
and Aux. Outputs on
Power Supply board
and ACMS8(CB)
Access Power
Controller’s outputs
Fail-Safe/Fail-Secure or Dry Form “C” Outputs Current Per ACMS8(CB) Output (A) ACMS8(CB) Board Input Fuse (PTC) Rating ACMS8(CB) Board Output Fuse (PTC) Rating PDS8(CB) Board Input Fuse (PTC) Rating PDS8(CB) Board Output Fuse (PTC) Rating
[DC] [Aux]
Output
Range
(VDC)
Output
Range
(VDC)
T2RM7CK1
4.5 6.3A/
250V
15A/
32V
20.17-
26.4
20.28-
26.4 24VDC @ 9.2A 8
2.5 15A/
32V
3A/
32V
10A/
32V
3A/
32V
T2RM7CK1D 2.0 9A 2.5A 9A 2.5A
Installing Trove2R into Rack Tower:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
These products are for indoor use only and must be installed within the protected premises.
Note: First assemble and Install Z Bracket Wire Management Accesory (refer to Z Bracket Installation pg. 3)
1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware).
2. In order to mount included cUL Listed tamper switch (Tane Model 3/8 ASH FM WH or equivalent),
turn the enclosure upside down and locate mounting holes (Fig. 1, pg. 2).
Insert the tamper switch flying leads into the center knockout of the three (3) holes from outside of the
drawer with the button facing outwards, make sure tamper switch is inserted properly then secure it
with the two (2) screws (supplied). Connect tamper switch wiring to the Access Control Panel input or
the appropriate UL Listed reporting device. To activate alarm signal open the rack drawer.
3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails (Rack drawer, pg. 8).
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.
6. Secure the rack cover (Fig. 2a, pg. 3) and rack drawer (Fig. 2b, pg. 3) to earth ground.
7. Ensure that all internal cofigurations (voltage selection, switch settings, etc.) are completed before
mounting backplane back into Trove rack enclosure.
Fig. 1
Back of the drawer,
viewed from outside.
Tamper Switch
mounting location
Fig. 2
Fig. 2a
Fig. 2b

T2RM7CK1(D) Installation Guide - 3 -
Z Bracket Installation for Trove2R:
Altronix Trove2R enclosure includes Z Bracket, a convenient and reliable wire management accessory.
Hardware (included):
Twelve (12) bolts and eight (8) lock nuts.
1. Carefully unpack Z Bracket. Do not discard included hardware
(Fig. 3, pg. 3).
2. Attach arms to each other using bolts and lock nuts (Fig. 4a, pg. 3).
3. Attach the hinge brackets to the ends of arms using bolts and nuts,
positioning them as shown on (Fig. 4b, pg. 3).
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on each end of Z Bracket, then attache the Z Bracket to the adjustable slide using bolts and lock nuts
(included) (Fig. 5, 5a, pg. 3).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).
Fig. 5
Fig. 5a
Fig. 4b
Fig. 3
Fig. 4a
Fig. 4
Fig. 3b

- 4 - T2RM7CK1(D) Installation Guide
T2RM7CK1(D): Configuration of Mercury Boards:
1. Fasten spacers onto metal pems configuration
(A), (B) or (C) of backplane depending on the
access controller (Fig. 6, pg. 4).
2. Position access controller module over corresponding
spacers and depress onto snap on spacers
(Fig. 6a, pg. 4).
3. Mount backplane to enclosure with hardware.
Mercury Access Controller
Position Chart for the
Following Models:
Mercury Pem Mounting
LNL-2220 / LP1502 A
LNL-1320 / MR52 B C D
PWR1 +
PWR2 +
COM -
COM -
PWR2 +
PWR1 +
+ PWR2 -- + PWR1 --
Altronix
ACMS8(CB)
with
VR6 below
+ INP1 --
PWR1 +OFF
IN1
IN2
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
+ INP2 --
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Altronix PDS8(CB)
D1 D2
IN1IN2 IN3IN4 IN5IN6 IN7IN8
IN9
GND
IN10
INPUTS
IN-5V
OUT-12V
J4
J2
RDR POWER
REG UNREG
GNDDAT CLK BZRLED V0CLKGNDDAT BZRLED V0
READER 1READER 2
PN REV SN
TR+
TR-
R+
R-
SG
AC
GND
ACDC
RS-485 12V
J5,J6
TERMINATOR
J5
J6
2W 4W
RS-485
J3
NO CNCNOC NC
RLY 1RLY 2RLY 3RLY 4
NO CNCNOC NC
RLY 5RLY 6
NO CNCNOC NC
65432
18
7
S1
OFF ON
MADE IN USA
READER INTERFACE
U10
COM
C2
C3
NO
NC
K1
C3
C2
COM K3
NO
NC
C3
C2
COM K5
NO
NC
C3
C2
COM K2
NO
NC
C3
C2
COM K4
NO
NC
C3
C2
COM K6
NO
NC
D1 D2
IN1IN2 IN3IN4 IN5IN6 IN7IN8
IN9
GND
IN10
INPUTS
IN-5V
OUT-12V
J4
J2
RDR POWER
REG UNREG
GNDDAT CLK BZRLED V0CLKGNDDAT BZRLED V0
READER 1READER 2
PN REV SN
TR+
TR-
R+
R-
SG
AC
GND
ACDC
RS-485 12V
J5,J6
TERMINATOR
J5
J6
2W 4W
RS-485
J3
NO CNCNOC NC
RLY 1RLY 2RLY 3RLY 4
NO CNCNOC NC
RLY 5RLY 6
NO CNCNOC NC
65432
18
7
S1
OFF ON
MADE IN USA
READER INTERFACE
U10
COM
C2
C3
NO
NC
K1
C3
C2
COM K3
NO
NC
C3
C2
COM K5
NO
NC
C3
C2
COM K2
NO
NC
C3
C2
COM K4
NO
NC
C3
C2
COM K6
NO
NC
D1 D2
IN1IN2 IN3IN4 IN5IN6 IN7IN8
IN9
GND
IN10
INPUTS
IN-5V
OUT-12V
J4
J2
RDR POWER
REG UNREG
GNDDAT CLK BZRLED V0CLKGNDDAT BZRLED V0
READER 1READER 2
PN REV SN
TR+
TR-
R+
R-
SG
AC
GND
ACDC
RS-485 12V
J5,J6
TERMINATOR
J5
J6
2W 4W
RS-485
J3
NO CNCNOC NC
RLY 1RLY 2RLY 3RLY 4
NO CNCNOC NC
RLY 5RLY 6
NO CNCNOC NC
65432
18
7
S1
OFF ON
MADE IN USA
READER INTERFACE
U10
COM
C2
C3
NO
NC
K1
C3
C2
COM K3
NO
NC
C3
C2
COM K5
NO
NC
C3
C2
COM K2
NO
NC
C3
C2
COM K4
NO
NC
C3
C2
COM K6
NO
NC
J4
J3
1
2
3
TMP
FLT
R1
R2
+
1
3
2
4
J8
RESET
S2
BT1
3V BR/CR2330
J1
5V
3.3V
2
3
4
1
S1
VBAT
IN1
K
1
K
2
K
3
K
4
K2 K1
K3
K4
IN2
IN3
IN4
IN5
IN6
IN7
IN8
8V
J6
J2
J5
J7
PASS 12V
GND
DAT
D0
TB8
READER 1
BZR
VO
GND
FLT
GND
TMP
GND
VIN
TB1
LED
D1
CLK
READER 2
D1
LED
VO
BZR
GND
CLK
D0
DAT
TB9
NO
OUT 1 C
NC
NO
OUT 2 C
NC
NC
OUT 4 C
NC
NO
NO
OUT 3 C
TB10TB11
RXD
CTS
GND
RTS
TXD
TB2
TB3
TR+
GND
TR-
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
TB4
TB5
TB6
TB7
-
(A) LNL-2220
(B) LNL-1320
(C) LNL-1320
(D) LNL-1320
NC C NO NC C NO
AC FAIL BAT FAIL
TRIGGER EOL SUPERVISED
AC DCAC1 NO GND
RESET + AUX -
--- BAT +
L G N
1 min enable 2 hr disable
--- DC +
Altronix
eFlow104NB
Fig. 6
Snap On
Spacer
Mercury Board
Backplane
Pem
Fig. 6a

T2RM7CK1(D) Installation Guide - 5 -
Notes:

- 6 - T2RM7CK1(D) Installation Guide
Notes:

T2RM7CK1(D) Installation Guide - 7 -
Notes:

- 8 - T2RM7CK1(D) Installation Guide
Trove2R Enclosure Dimensions (H x W x D approximate):
3.375” x 19.0” x 33.25” (85.8mm x 482.6mm x 844.6mm). Shown with Z Bracket attached.
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIT2RM7CK1(D) G24W MEMBER
39.76” (1,001mm)
33.6” (853.4mm)
4.2” (106.7mm)
11.2” (284.5mm)
0.52” (13.2mm)
0.63” (16mm)
15.05” (382.3mm)
4.5” (114.3mm)
5.35” (135.9mm)
0.72”
(18.3mm)
15.14” (384.4mm)
1.5”
(38.1mm)