Altronix 220VAC Series User manual

ALTV248Hi220
- 24VAC @ 12.5A total output.
- Eight (8) 1.75A Fuse Protected
Isolated Outputs.
ALTV248Mi220
- 24VAC @ 12.5A total output.
- Eight (8) 1.6A Fuse Protected
Isolated Outputs.
ALTV2416i220
- 24VAC @ 25A total output.
- Sixteen (16) 1.75A Fuse Protected
Isolated Outputs.
ALTV248CBHi220
- 24VAC @ 12.5A total output.
- Eight (8) 1.75A PTC Protected
Isolated Outputs.
ALTV248CBMi220
- 24VAC @ 12.5A total output.
- Eight (8) 1.6A PTC Protected
Isolated Outputs.
ALTV2416CBi220
- 24VAC @ 25A total output.
- Sixteen (16) 1.75A PTC Protected
Isolated Outputs.
220VAC Isolated Series
CCTV Power Supplies
Models Include:
Installation Guide
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Rev. 041112 More than just power.TM

- 2 - Isolated 220 Series Installation Guide
Overview:
Altronix Isolated CCTV Power Supplies provide 24VAC distributed via eight (8) or sixteen (16) fuse or PTC protected
isolated outputs for powering CCTV cameras, heaters, and other video accessories.
Isolated Power Supply Reference Chart:
Altronix
Model Number
Output
Voltage
Total
Output
Current
Number
of
Outputs
PTC Protected
auto-resettable
Outputs
Fuse
Protected
Outputs
Output
Current
(max per
output)
220VAC
50/60Hz
Input
Current
ALTV248Hi220 24VAC 14A 8 – P1.75A
2.7A
ALTV248CBHi220 24VAC 8 P–
ALTV248Mi220 24VAC 12.5A 8 – P1.6A
ALTV248CBMi220 24VAC 8 P–
ALTV2416i220 24VAC 28A 16 – P1.75A 5.4A
ALTV2416CBi220 24VAC 16 P–
Specifications:
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all
local codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pgs. 7, 8). Secure enclosure to earth ground.
2. Set power switch to OFF position on all models (Fig. 1 - 3, pgs. 4 - 6).
3. All units are factory set for 24VAC operation.
4. Connect unswitched AC circuit (220VAC, 50/60Hz) as follows: Green branch wire (ground) connects to the
terminal marked , Line connects to the terminal marked [L], and Neutral connects to the terminal marked
[N] of the Inlet Appliance Connector. (Fig. 1 - 3, pgs. 4 - 6).
Use 18 AWG or larger for all power connections (Battery, AC output).
5. Measure output voltage before connecting devices. This helps avoiding potential damage.
Terminals marked [1A - 8A] and [1B - 8B] are of the same polarity (phase).
6. Connect CCTV cameras to output terminals using the following procedure:
Camera 1 to output 1A & 1B. Camera 5 to output 5A & 5B.
Camera 2 to output 2A & 2B. Camera 6 to output 6A & 6B.
Camera 3 to output 3A & 3B. Camera 7 to output 7A & 7B.
Camera 4 to output 4A & 4B. Camera 8 to output 8A & 8B.
7. Set power switch on all models to the “RESET” (ON) position (Fig. 1 - 3, pgs. 4 - 6).
8. Upon completion of the wiring, secure enclosure door with screws (supplied).
Input:
• 220VAC, 50/60Hz.
Output:
• Eight (8) or sixteen (16) fuse or PTC
protected outputs.
• 24VAC outputs.
• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
• Surge suppression.
Features:
• Individual electronically isolated outputs.
• Illuminated master Power ON/OFF switch
with built-in circuit breaker.
Features (cont’d):
• Unit maintains camera synchronization.
• Ease of installation saves time & eliminates
costly labor.
• Spare fuses included (on fuse protected models).
Enclosure Dimensions (H x W x D approx.):
ALTV248Mi220, ALTV248UCBMi220:
8.5” x 7.5” x 3.875” (215.9mm x 191mm x 98.4mm).
ALTV248Hi220, ALTV248CBHi220,
ALTV2416i220, and ALTV2416CBi220:
13.5” x 13” x 3.25”
(342.9mm x 330.2mm x 82.6mm).
Illuminated Power Disconnect
Circuit Breaker with manual reset
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
Used on ALTV248CBHi220
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
Input
220VAC, 50/60Hz
4A
250V

Isolated 220 Series Installation Guide - 3 -
CAUTION: Equipment to be installed/serviced by authorized/trained personnel only.
Shut branch circuit power before installing/servicing equipment.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.
Replace fuses with the same type and rating (3.5A/250V).
Terminal Identification:
PD8i - Distribution Module
1A - 8A Phase 1
1B - 8B Phase 2
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of
sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.

- 4 - Isolated 220 Series Installation Guide
Illuminated Power Disconnect Circuit Breaker with manual reset
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
Used on ALTV248CBHi220
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
Input 220VAC, 50/60Hz
4A
250V
Fig. 1 - ALTV248Hi220 and ALTV248CBHi220

Isolated 220 Series Installation Guide - 5 -
Fig. 2 - ALTV248Mi220 and ALTV248CBMi220
Illuminated Power Disconnect Circuit Breaker with manual reset
Transformer
underneath
power distribution
board PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
Used on ALTV248CBMi220
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
Input
220VAC,
50/60Hz
4A
250V

- 6 - Isolated 220 Series Installation Guide
Fig. 3 - ALTV2416i220 and ALTV2416CBi220
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
Used on ALTV2416CBi220
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
Illuminated Power Disconnect Circuit Breaker with manual reset
Input 220VAC, 50/60Hz
4A
250V

Isolated 220 Series Installation Guide - 7 -
Enclosure Dimensions (H x W x D) for:
• ALTV248Mi220 • ALTV248CBMi220
8.5” x 7.5” x 3.875” (215.9mm x 191mm x 98.4mm)
3.63” (92.2mm) 1.25” (31.75mm)
3.85” (97.79mm)
7.25” (184.15mm)
1.75” (44.45mm) 1” (25.4mm)
0.6” (15.24mm) 0.6” (15.24mm)
0.9” (22.86mm) 0.9” (22.86mm)
8.13” (206.5mm)
3.85” (97.79mm)
1.25” (31.75mm)
1” (25.4mm)
1” (25.4mm) 1” (25.4mm)
1” (25.4mm)
1” (25.4mm)
1.25” (31.75mm)
1” (25.4mm)
1.25” (31.75mm)
0.6” (15.24mm) 0.6” (15.24mm)

- 8 - Isolated 220 Series Installation Guide
1.40”
(35.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
4.85” (123.2mm) 4.85” (123.2mm)
3.25” (82.6mm)
0.75”
(19.1mm)
0.75”
(19.1mm)
11.0” (279.4mm)
12.5” (317.5mm)
1.20”
(30.5mm)
1.20”
(30.5mm)
0.9375” (23.8mm)
0.9375” (23.8mm)
5.10” (129.5mm)
1.40”
(35.6mm)
5.10” (129.5mm)
6.5625” (166.7mm)
3.25” (82.6mm)3.25” (82.6mm)
3.25” (82.6mm)
10.5” (266.7mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.0” (25.4mm)
13.0” (330.2mm)
5.10” (129.5mm)
1.20”
(30.5mm)
Enclosure Dimensions (H x W x D) for:
• ALTV248Hi220 • ALTV248CBHi220
• ALTV2416i220 • ALTV2416CBi220
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIIsolated 220 Series F10V MEMBER