Altronix ALTV244 Operating and maintenance instructions

Rev. 020705
ALTV244 Series
CCTV Power Supplies
Installation Guide
Models Include:
• ALTV244 • ALTV244CB
- 24VAC @ 4 amp (100VA) - 24VAC @ 4 amp (100VA)
or 28VAC @ 3.5 amp. or 28VAC @ 3.5 amp.
- Four (4) Fuse Protected - Four (4) PTC Protected
Outputs. Outputs.
• ALTV244175 • ALTV244175CB
- 24VAC @ 7.25 amp (175VA) - 24VAC @ 7.25 amp (175VA)
or 28VAC @ 6.25 amp. or 28VAC @ 6.25 amp.
- Four (4) Fuse Protected - Four (4) PTC Protected
Outputs. Outputs.
• ALTV244300 • ALTV244300CB
- 24VAC @ 12.5 amp (300VA). - 24VAC @ 12.5 amp (300VA).
or 28VAC @ 10 amp. or 28VAC @ 10 amp.
- Four (4) Fuse Protected - Four (4) PTC Protected
Outputs. Outputs.

Overview:
These Altronix CCTV Power Supplies provide 24VAC or 28VAC distributed via four (4) fuse or PTC protected outputs
for powering CCTV Cameras, heaters and other video accessories.
Four (4) Output ALTV244 Reference Chart:
ALTV244 4 amp 24VAC 4 - x 3.5 amp 5 amp/250V .9 amp
3.5 amp 28VAC
ALTV244CB 4 amp 24VAC 4 x - 2.5 amp 5 amp/250V .9 amp
3.5 amp 28VAC
ALTV244175
7.25 amp 24VAC 4 - x 3.5 amp 10 amp/250V 1.5 amp
6.25 amp 28VAC
ALTV244175CB
7.25 amp 24VAC 4 x - 2.5 amp 10 amp/250V 1.5 amp
6.25 amp 28VAC
ALTV244300 12.5 amp 24VAC 4 - x 3.5 amp 15 amp/32V 2.7 amp
10 amp 28VAC
ALTV244300CB 12.5 amp 24VAC 4 x - 2.5 amp 15 amp/32V 2.7 amp
10 amp 28VAC
Specifications:
• Surge suppression. Enclosure Dimensions:
• AC power LED indicator. ALTV244, ALTV244CB
• Power ON/OFF switch 8.5”H x 7.5”W x 3.5”D
• Unit maintains camera synchronization. ALTV244175, ALTV244175CB, ALTV244300
• Ease of installation saves time & eliminates costly labor. and ALTV244300CB
• Spare fuses included (on fuse protected models). 8.5”H x 7.5”W x 3.75”D
Installation Instructions:
1. Mount unit in desired location.
2. Slide switch SW1 to OFF position (Models ALTV244 and ALTV244CB), (Fig. 1, pg. 3).
Turn main switch on all other models to the OFF position.
3. All units are factory set for 24VAC operation.
For 28VAC operation, adjust unit prior to mounting and applying
power as follows: Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and
the yellow wire [24V] is connected to the terminal marked [S].
4. Connect AC power to the black and white flying lead of the transformer (Fig. 1, pg. 3).
Use 18 AWG or larger for all power connections (Battery, AC output).
5. Measure output voltage before connecting devices. This helps avoid potential damage.
Terminals marked [1P - 4P] are positive (+) and terminals marked [1N - 4N] are negative.
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the
output voltage.
Altronix
Model Number
Output Current
(max per output)
Total Output Current
(Power)
Output Voltage
115VAC
50/60Hz Input
Current
PTC Protected
Outputs
Fuse Protected
Outputs
- 2 -
Number of
Outputs
Main Fuse Ratings

6. Connect devices to terminals marked [1P - 1N through 4P - 4N] on PD4/PD4CB board carefully observing
correct polarity (Fig. 1, pg. 3).
7. Slide switch SW1 to ON position (Models ALTV244 and ALTV244CB), (Fig. 1, pg. 3).
Turn main switch on all other models to the “RESET” (ON) position.
8. Green LED will illuminate when unit is powered.
9. Upon completion of wiring, secure enclosure door with screws (supplied).
Caution: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes
and in accordance with the National Electrical Code.
Terminal Identification:
PD4/PD4CB - Distribution Module
1P - 4P Positive AC output.
1N - 4N Negative AC output.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient
magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There are
no user serviceable parts inside. Refer servicing to qualified service personnel.
- 3 -

ALTV244
XFMR
24VAC or 28VAC
fused output 1
(Follow same procedure
using terminals 2P & N
thru 4P & N fused
outputs 2 thru 4)
115 VAC input
50/60 Hz,
.9 amps
White Lead
Black Lead
F1 F2 F3 F4
ON
INPUT
OFF
JMP1
JMP1
1P 1N 2P 2N 3P 3N 4P 4N
LED
SW1
MAIN FUSE
NPS
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
XFMR
24VAC or 28VAC
circuit breakered output 1
(Follow same procedure
using terminals 2P & N thru
4P & N circuit breakered
outputs 2 thru 4)
115 VAC input
50/60 Hz,
.9 amps
White Lead
Black Lead
F1 F2 F3 F4
ON
INPUT
OFF
1P 1N 2P 2N 3P 3N 4P 4N
LED
SW1
MAIN FUSE
NP
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
JMP1
JMP1
S
ALTV244CB
- 4 -
NP S
NP S
24VAC
Output
(Yellow) (Black)
(Black) (Yellow)
28VAC
Output
Voltage Selection
Configuration

ALTV244175
XFMR
White Lead
24VAC or 28VAC fused output 1
(Follow same procedure
using terminals 2P & N
thru 4P & N fused
outputs 2 thru 4)
F1 F2 F3 F4
INPUT
1P 1N 2P 2N 3P 3N 4P 4N
LED
MAIN FUSE
P
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
S
Power
Switch
Black
Lead
115VAC input
50/60 Hz,
1.5 amps
N
F1 F2 F3 F4
INPUT
1P 1N 2P 2N 3P 3N 4P 4N
LED
MAIN FUSE
NP
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
XFMR
White Lead
24VAC or 28VAC circuit breakered 1
(Follow same procedure
using terminals 2P & N
thru 4P & N fused
outputs 2 thru 4)
S
Power
Switch
Black
Lead
N
115VAC input
50/60 Hz,
1.5 amps
ALTV244175CB
- 5 -
NP S
NP S
24VAC
Output
(Yellow) (Black)
(Black) (Yellow)
28VAC
Output
Voltage Selection
Configuration

ALTV244300
Transformer
underneath
power supply
board
Power
Switch
White Lead
Black Lead
F1 F2 F3 F4
INPUT
1P 1N 2P 2N 3P 3N 4P 4N
LED
P
1P, 2P, 3P, 4P = FUSED OUTPUTS 1N, 2N, 3N, 4N = COMMON OUTPUTS
S
MAIN FUSE
N
Transformer
underneath
power supply
board
Power
Switch
F1 F2 F3 F4
INPUT
1P 1N 2P 2N 3P 3N 4P 4N
LED
MAIN FUSE
P
1P, 2P, 3P, 4P = FUSED OUTPUTS 1N, 2N, 3N, 4N = COMMON OUTPUTS
S
White Lead
Black Lead
N
ALTV244300CB
- 6 -
NP S
NP S
24VAC
Output
(Yellow) (Black)
(Black) (Yellow)
28VAC
Output
Voltage Selection
Configuration

TOP ONLY
Enclosure Dimensions for:
• ALTV244
• ALTV244CB
• ALTV244175
• ALTV244175CB
• ALTV244300
• ALTV244300CB
8.5"H x 7.5"W x 3.5"D
- 7 -

Altronix Corp.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
web site: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
II1ALTV244Series B17E
Altronix is not responsible for any typographical errors.
- 8 -
MEMBER
Notes: