Altronix ALTV248ULHi User manual

ALTV248ULHi
- 24VAC @ 12.5A total output.
- Eight (8) 1.56A Fuse Protected
Isolated Outputs.
ALTV248ULMi
- 24VAC @ 12.5A total output.
- Eight (8) 1.56A Fuse Protected
Isolated Outputs.
ALTV2416ULi
- 24VAC @ 25A total output.
- Sixteen (16) 1.56A Fuse Protected
Isolated Outputs.
ALTV248ULCBHi
- 24VAC @ 12.5A total output.
- Eight (8) 1.56A PTC Protected
Isolated Outputs.
ALTV248ULCBMi
- 24VAC @ 12.5A total output.
- Eight (8) 1.56A PTC Protected
Isolated Outputs.
ALTV2416ULCBi
- 24VAC @ 25A total output.
- Sixteen (16) 1.56A PTC Protected
Isolated Outputs.
Rev. 113004
More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Installation Guide
UL Listed Isolated Series
CCTV Power Supplies
Models Include:
For models with factory installed 3-wire line cord add suffix “3” (e.g. ALTV248ULHi3).

- 2 - UL Listed Isolated Series Installation Guide
Overview:
Altronix Isolated CCTV Power Supplies provide 24VAC distributed via eight (8) or sixteen (16) fuse or PTC protected
isolated outputs for powering CCTV cameras, heaters, and other video accessories.
Isolated Power Supply Reference Chart:
Altronix
Model Number
Output Voltage Total Output Current Number of Outputs PTC Protected auto- resettable Outputs (Class 2 Power- Limited for dry locations) Fuse Protected Outputs Output Current (max per output) 115VAC 50/60Hz Input Current Agency Listing
ALTV248ULHi 24VAC 12.5A 8 – P1.56A 3A
ALTV248ULCBHi 24VAC 12.5A 8 P– 1.56A 3A
ALTV248ULMi 24VAC 12.5A 8 – P1.56A 3A
ALTV248ULCBMi 24VAC 12.5A 8 P– 1.56A 3A
ALTV2416ULi 24VAC 25A 16 – P1.56A 6A
ALTV2416ULCBi 24VAC 25A 16 P- 1.56A 6A
Add suffix “3” for 3-wire line cord (e.g. ALTV248ULHi3).
Specifications:
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all
local codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 7, 8). Secure enclosure to earth ground.
2. Set power switch to OFF position on all models (Fig. 1 - 3, pg. 4 - 6).
3. All units are factory set for 24VAC operation.
4. Secure green lead to earth ground. Connect AC power to the black and white flying leads of the
transformer(s) (Fig. 1 - 3, pg. 4 - 6). Use 18 AWG or larger for all power connections.
Keep power-limited wiring (PTC protected outputs only) separate from non power-limited wiring.
Minimum 0.25” spacing must be provided. Use separate knockouts
5. Measure output voltage before connecting devices. This helps avoiding potential damage.
Terminals marked [1A - 8A] and [1B - 8B] are of the same polarity (phase).
Agency Listings:
• UL Listed for Commercial CCTV Equipment (UL2044).
CUL Listed - CSA Standard C22.2 No.1-98,
Audio, Video and Similar Equipment.
Input:
• 115VAC, 50/60Hz.
Output:
• Eight (8) or sixteen (16) fuse or PTC
protected outputs.
• 24VAC outputs.
• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
• Surge suppression.
Features:
• Individual electronically isolated outputs.
• Illuminated master Power ON/OFF switch
with built-in circuit breaker.
• Unit maintains camera synchronization.
• Ease of installation saves time & eliminates
costly labor.
• Spare fuses included (on fuse protected models).
Enclosure Dimensions (H x W x D approx.):
ALTV248ULMi, ALTV248ULCBMi:
8.5” x 7.5” x 3.875” (215.9mm x 191mm x 98.4mm).
ALTV248ULHi, ALTV248ULCBHi,
ALTV2416ULi, and ALTV2416ULCBi:
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm).

UL Listed Isolated Series Installation Guide - 3 -
6. Connect CCTV cameras to output terminals using the following procedure:
Camera 1 to output 1A & 1B. Camera 5 to output 5A & 5B.
Camera 2 to output 2A & 2B. Camera 6 to output 6A & 6B.
Camera 3 to output 3A & 3B. Camera 7 to output 7A & 7B.
Camera 4 to output 4A & 4B. Camera 8 to output 8A & 8B.
7. Set power switch on all models to the “RESET” (ON) position (Fig. 1 - 3, pg. 4 - 6).
8. Upon completion of the wiring, secure enclosure door with screws (supplied).
Caution: Equipment to be installed/serviced by authorized/trained personnel only.
Shut branch circuit power before installing/servicing equipment.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This
installation should be made by qualified service personnel and should conform to the National Electrical
Code and all local codes. Use 75˚C or higher rated UL insulated wiring for connecting the unit to the
mains. Replace fuses with the same type and rating (3.5A/250V).
Terminal Identification:
PD8i - Distribution Module
1A - 8A Phase 1
1B - 8B Phase 2
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of
sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.

- 4 - UL Listed Isolated Series Installation Guide
Illuminated Power Disconnect
Circuit Breaker with manual reset
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
non power-
limited
Used on ALTV248ULCBHi
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
Class 2 power-limited
Black Lead
White Lead
Green Lead
(ground)
Input 115VAC, 50/60Hz
Fig. 1 - ALTV248ULHi and ALTV248ULCBHi

UL Listed Isolated Series Installation Guide - 5 -
Fig. 2 - ALTV248ULMi and ALTV248ULCBMi
Illuminated Power Disconnect
Circuit Breaker with manual reset
Transformer
underneath
power
distribution
board
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
Used on ALTV248ULCBMi
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
non power-
limited
Class 2 power-limited
Input
115VAC,
50/60Hz
Green Lead (ground)

- 6 - UL Listed Isolated Series Installation Guide
Fig. 3 - ALTV2416ULi and ALTV2416ULCBi
non power-
limited
non power-
limited
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
PD8I
ISOLATED POWER
DISTRIBUTING BOARD
F1 F2 F3 F4 F5 F6 F7 F8
Used on ALTV2416ULCBi
1A 2A 3A 4A 5A 6A 7A 8A
1B 2B 3B 4B 5B 6B 7B 8B
Illuminated Power Disconnect
Circuit Breaker with manual reset
Class 2 power-limited
Green Lead
(ground)
Input 115VAC, 50/60Hz

UL Listed Isolated Series Installation Guide - 7 -
Enclosure Dimensions (H x W x D) for:
• ALTV248ULMi • ALTV248ULCBMi
8.5” x 7.5” x 3.875” (215.9mm x 191mm x 98.4mm)
3.63” (92.2mm) 1.25” (31.75mm)
3.85” (97.79mm)
7.25” (184.15mm)
1.75” (44.45mm) 1” (25.4mm)
0.6” (15.24mm) 0.6” (15.24mm)
0.9” (22.86mm) 0.9” (22.86mm)
8.13” (206.5mm)
3.85” (97.79mm)
1.25” (31.75mm)
1” (25.4mm)
1” (25.4mm) 1” (25.4mm)
1” (25.4mm)
1” (25.4mm)
1.25” (31.75mm)
1” (25.4mm)
1.25” (31.75mm)
0.6” (15.24mm) 0.6” (15.24mm)

- 8 - UL Listed Isolated Series Installation Guide
1.40”
(35.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
4.85” (123.2mm) 4.85” (123.2mm)
3.25” (82.6mm)
0.75”
(19.1mm)
0.75”
(19.1mm)
11.0” (279.4mm)
12.5” (317.5mm)
1.20”
(30.5mm)
1.20”
(30.5mm)
0.9375” (23.8mm)
0.9375” (23.8mm)
5.10” (129.5mm)
1.40”
(35.6mm)
5.10” (129.5mm)
6.5625” (166.7mm)
3.25” (82.6mm)3.25” (82.6mm)
3.25” (82.6mm)
10.5” (266.7mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.0” (25.4mm)
13.0” (330.2mm)
5.10” (129.5mm)
1.20”
(30.5mm)
Enclosure Dimensions (H x W x D) for:
• ALTV248ULHi • ALTV248ULCBHi
• ALTV2416ULi • ALTV2416ULCBi
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIULisolated Series L03U MEMBER