Altronix R615DC8CB220 User manual

R615DC8CB220
CCTV Rack Mount DC Power Supply
- 6-15VDC @ 4A.
- Eight (8) PTC Protected Outputs.
Installation Guide
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Rev. 052316 More than just power.TM

- 2 - R615DC8CB220 Installation Guide
Installation Instructions:
1. Unit is factory set at 12VDC. To adjust the output voltage remove the bottom cover to access trimpot on
the power supply board (Fig. 1b, pg. 2).
2. Mount unit in the desired rack location. Space unit at least 3” from any video monitors.
3. Set power switch on the back of the unit to the OFF position (Fig. 1d, pg. 2, Fig. 2, pg. 4).
4. Plug power cord into a grounded 220VAC, 50/60Hz receptacle (Fig. 1c, pg. 2).
5. Set power switch to the ON (RESET) position and measure output voltage before connecting devices.
This helps avoiding potential damage.
6. Set power switch on the back of the unit to the OFF position.
7. Connect devices to the removable terminal blocks marked [1P & 1N] through [8P & 8N] (Fig. 1a, pg. 2).
When wiring is completed on the terminal blocks they can be locked down by tightening screw flanges.
All terminals with common suffix (P) “1P, 2P...” are the same polarity (positive).
All terminals with common suffix (N) “1N, 2N...” are the same polarity (negative).
8. Upon completion of the wiring, set power switch on back of unit to the ON (RESET) position.
9. Green power LEDs on faceplate will illuminate when AC power is present. When an output is in a trouble
condition (tripped PTC), the corresponding LED will not be illuminated (Fig. 1).
Tripped PTC - To reset PTC, set power switch on back of unit to the OFF position.
After approximately 30 secs. set power switch to the ON (RESET) position.
10. Power switch with built-in circuit breaker:
OFF position - Switch not illuminated. Outputs not powered.
RESET (ON) position - Switch illuminated. Outputs powered.
Circuit breaker tripped - Switch not illuminated. Power LEDs on faceplate are not illuminated.
Outputs not powered.
To reset circuit breaker set power switch to the ON (RESET) position (Fig. 1d, pg. 2, Fig. 2, pg. 4).
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.
CAUTION: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
Input:
• 220VAC (working range 198VAC - 256VAC),
50/60Hz, 0.5A.
Output:
• Eight (8) PTC protected outputs.
• 6-15VDC @ 4A total output current.
(0.5A per device, 2.5A max.)
• Outputs are rated @ 2.5A.
• Filtered and electronically regulated outputs.
• Short circuit and thermal overload protection.
Features:
• Eight (8) power LEDs.
• Illuminated master power disconnect circuit
breaker with manual reset.
• 3-wire grounded line cord.
• Removable terminal blocks with locking
screw flange.
Enclosure Dimensions (H x W x D approx.):
3.26” x 19.125” x 8.5” (83mm x 486mm x 216mm)
Overview:
Altronix R615DC8CB220 rack mount CCTV Power Supply is designed with eight (8) individually PTC protected
outputs for powering CCTV cameras and other video accessories. It provides 6VDC-15VDC distributed via eight
(8) outputs with a total of up to 4A total continuous supply current.
Specifications:

R615DC8CB220 Installation Guide - 3 -
PN
Power
LEDs
Power
LEDs
+
DC
OUTPUT
-
- BAT +
AC AC
DC
AC
Voltage
Adjustment
PTC1 PTC1 PTC1 PTC1 PTC1 PTC1 PTC1 PTC1
Removable Terminal
Block Strain Relief
Line Cord Power Switch
Trimpot
XFMR
Fig. 1
Fig. 1a Fig. 1b Fig. 1c Fig. 1d
Terminal Identification:
AL400ULB - Power Supply Board
Terminal Legend Function/Description
AC/AC Low voltage AC input (24VAC 100VA) Altronix part #T24130/220
+ DC –6VDC-15VDC @ 4A total continuous output.
PD8CB - Distribution Module
Terminal Legend Function/Description
1P - 8P Positive DC output
1N - 8N Negative DC output
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of
sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of import-
ant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.

- 4 - R615DC8CB220 Installation Guide
Enclosure Dimensions (H x W x D approximate):
3.26” x 19.125” x 8.5” (83mm x 486mm x 216mm)
N PN PN PN
PN
PNPN PN P
OFF
RESET
8 7 654 3 21
Bottom View
Rear View
Front View
17.5” (444.5mm)
19.125” (486mm)
2.95” (75mm)
0.65” (16.5mm)
8.5” (215.9mm)
1.0” (25.4mm)
2.52”
(64mm)
1.5”
(38mm)
3.26” (83mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIR615DC8CB220 K23U MEMBER