Altronix SMP10C24X Series User manual

Rev. 071212 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
SMP10C24X Series
Power Supply/Chargers
Models Include:
SMP10C24X
SMP10PMC24X
- Single Output.
SMP10PM24P4
- Four (4) Fuse Protected Outputs.
SMP10PM24P8
- Eight (8) Fuse Protected Outputs.
SMP10PM24P16
- Sixteen (16) Fuse Protected Outputs.
SMP10PM24P4CB
- Four (4) PTC Protected Outputs.
SMP10PM24P8CB
Eight (8) PTC Protected Outputs.
SMP10PM24P16CB
- Sixteen (16) PTC Protected Outputs.
Installation Guide

- 2 - SMP10C24X Series Installation Guide
Overview:
Altronix SMP10C24X Series power supply/chargers convert a 115VAC, 60Hz input into a regulated 24VDC output
with up to 10A of continuous load current (see specifications).
SMP10C24X Series Power Supply Configuration Reference Chart:
Altronix
Model Number
Accessory
Power
Distribution
Module(s)
Number
of
Outputs
Fused Outputs PTC Outputs (auto- resettable) Individual Output Rating (A) Supervised
115VAC
50/60Hz
Input
Current
(A)
24VDC
Total
Output
Current
(A)
SMP10C24X - 1 – – 10A –
2.7A 10A
SMP10PMC24X – –
P
SMP10PM24P4 PD4 4P– 3.5A
SMP10PM24P4CB PD4CB – P2.5A
SMP10PM24P8 PD8 8P– 3.5A
SMP10PM24P8CB PD8CB – P2.5A
SMP10PM24P16 PD16W 16 P– 3.5A
SMP10PM24P16CB PD16WCB – P2.5A
Specifications:
Input:
• Input 115VAC, 50/60Hz, 2.7A.
Output:
• 24VDC output.
• 10A supply current.
• Filtered and electronically regulated outputs.
• Short circuit and thermal overload protection.
Battery Backup:
• Built-in charger for sealed lead acid or
gel type batteries.
• Maximum charge current 0.7A.
• Zero voltage drop when switching over to
battery backup.
Features:
• Power ON/OFF switch.
Supervision (select models):
• AC fail supervision (form “C” contacts).
• Battery presence and low battery supervision
(form “C” contacts).
Visual Indicators:
• AC input and DC output LED indicators.
Electrical:
• Operating temperature: 0ºC to 49ºC ambient.
• BTU/Hr. (approx.): 122 BTU/Hr.
• System AC input VA requirement: 310.5VA.
Mechanical:
• Enclosure Dimensions (H x W x D approx.):
13.5” x 13” x 3.25”
(342.9mm x 330.2mm x 82.6mm)
- Accommodates up to
two (2)12VDC/7AH batteries.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all
local codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure’s upper keyholes over the two upper screws; level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 8). Secure enclosure to earth ground.
2. Slide [Power ON/OFF] switch to OFF position (Fig. 1a, pg. 4).
3. Connect AC power to the terminals marked [L & N], connect ground to the green flying lead (Fig. 1, pg. 4,
Fig. 2, pg. 5).
Use 18 AWG or larger for all power connections (Battery, DC output).
Use 22 AWG to 18 AWG for power-limited circuits (AC Fail/Low Battery reporting).
4. Slide [Power ON/OFF] switch to ON position.
5. Measure output voltage before connecting devices. This helps avoiding potential damage.
Keep power-limited wiring separate from non power-limited wiring (115VAC, 60Hz Input,
Battery Wires). Minimum 0.25” spacing must be provided.

SMP10C24X Series Installation Guide - 3 -
CAUTION: Do not touch exposed metal parts.
Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.
6. Slide [Power ON/OFF] switch to OFF position.
7. Connect devices to be powered:
a. For Power Supply Board connect to the terminals marked [– DC +].
b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked
[1P & 1N] through [4P & 4N] (Fig. 3, pg. 6), 1 to 8 marked [1P & 1N] through [8P & 8N] (Fig. 4, pg. 6),
or 1 to 16 marked [1P & 1N] through [16P & 16N] (Fig. 5, pg. 6),carefully observing correct polarity.
Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board (Fig. 1a, pg. 4,
Fig. 2a, pg. 5).
When servicing the unit, AC mains should be removed.
8. When using stand-by batteries, they must be lead acid or gel type.
Connect battery to the terminals marked [– BAT +] (battery leads included).
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.
For supervised models only:
9. Connect appropriate signaling notification devices to AC Fail and Low Bat supervisory relay outputs
marked [NC, C, NO] (Fig. 1b, pg. 4 or Fig. 2b, pg. 5).
10. Slide [Power ON/OFF] switch to ON position.
LED Diagnostics:
Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery is supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
Power Distribution Module
Green Power Distribution Module Status
ON Normal operating condition.
OFF No Power Output.
Terminal Identification:
Power Supply Board:
Terminal Legend Function/Description
L, G, N Connect 115VAC to these terminals: L to Hot, N to Neutral.
– DC + 24VDC @ 10A continuous output.
*AC FAIL
NC, C, NO
Used to notify loss of AC power, e.g. connect to audible device or alarm panel.
Relay normally energized when AC power is present.
Contact rating 1A @ 120VAC / 28VDC.
*Low Battery
NC, C, NO
Used to indicate low battery condition, e.g. connect to alarm panel. Relay normally
energized when DC power is present. Contact rating 1A @ 120VAC / 28VDC.
Low battery threshold: 24VDC output threshold set @ approximately 21VDC.
– BAT + Stand-by battery connections. Maximum charge rate 0.7A.
*Note: Supervised models only
PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module:
Terminal Legend Function/Description
PD4/PD4CB PD8/PD8CB PD16W/PD16WCB
1P to 4P 1P to 8P 1P to16P Positive DC power outputs.
1N to 4N 1N to 8N 1N to 16N Negative DC power outputs.

- 4 - SMP10C24X Series Installation Guide
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT +--- DC +
LGN
5A 250V
OFF ON
AC DC
Power Supply
Board
Green
Lead
115VAC
power
mains
Power
Distribution
Module(s)
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT +--- DC +
LGN
5A 250V
OFF ON
AC DC
Power Supply
Board
Green
Lead
115VAC
power
mains
Power
Distribution
Module(s)
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT +--- DC +
LGN
5A 250V
OFF ON
AC DC
Power Supply
Board
Green
Lead
115VAC
power
mains
Power
Distribution
Module(s)
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
Fig. 1
Fig. 1a
Switch disables power mains line voltage input.
If stand-by battery (batteries) are connected, the DC output remains on
Fig. 1b See
LED Diagnostics,
pg. 3
Caution: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of
sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open
enclosure. There are no user serviceable parts inside.
Refer servicing to qualified service personnel.

SMP10C24X Series Installation Guide - 5 -
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT +--- DC +
LGN
5A 250V
OFF ON
AC DC
Power Supply
Board
Green
Lead
115VAC
power
mains
Power
Distribution
Module
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT +--- DC +
LGN
5A 250V
OFF ON
AC DC
Power Supply
Board
Green
Lead
115VAC
power
mains
Power
Distribution
Module
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT +--- DC +
LGN
5A 250V
OFF ON
AC DC
Power Supply
Board
Green
Lead
115VAC
power
mains
Power
Distribution
Module
Optional Rechargeable
Stand-by Battery
Optional Rechargeable
Stand-by Battery
Fig. 2
Fig. 2a
Switch disables power mains line voltage input.
If stand-by battery (batteries) are connected, the DC output remains on
Fig. 2b
See
LED Diagnostics,
pg. 3

- 6 - SMP10C24X Series Installation Guide
INPUT
LED
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
F1 F2 F3 F4
COMMON POWER OUTPUTS
1P 1N 2P 2N 3P 3N 4P 4N
DC Output to devices From Power Supply
Board
(Factory Installed)
Used on
PTC Models
N
COMMON POWER OUTPUTS
P
FUSED POWER OUTPUTS
1 2 3 4 5 6 7 8
D1
INPUT
R1 LED
ON OFF
SW1
Used on
PTC Models
DC Output to devices From Power Supply
Board
(Factory Installed)
Power Distribution Module(s):
common
outputs
protected
outputs
P
N
NPS
XFMR Input
12345678
9 10 11 12 13 14 15 16
PN
3.5A 250V
For continuous protection against risk of fire
replace fuses with same type and rating.
Used on
PTC Models
Fig. 3 - PD4/PD4CB
Fig. 4 - PD8/PD8CB
Fig. 5 - PD16W/PD16WCB

SMP10C24X Series Installation Guide - 7 -
Notes:

- 8 - SMP10C24X Series Installation Guide
Enclosure Dimensions (BC300):
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)
Enclosure accommodates up to two (2) 12VDC/7AH batteries.
Also available to accommodate up to two (2) 12VDC/12AH batteries (please contact Altronix).
1.40”
(35.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
4.85” (123.2mm) 4.85” (123.2mm)
3.25” (82.6mm)
0.75”
(19.1mm)
0.75”
(19.1mm)
11.0” (279.4mm)
12.5” (317.5mm)
1.20”
(30.5mm)
1.20”
(30.5mm)
0.9375” (23.8mm)
0.9375” (23.8mm)
5.10” (129.5mm)
1.40”
(35.6mm)
5.10” (129.5mm)
6.5625” (166.7mm)
3.25” (82.6mm)3.25” (82.6mm)
3.25” (82.6mm)
10.5” (266.7mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.0” (25.4mm)
13.0” (330.2mm)
5.10” (129.5mm)
1.20”
(30.5mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IISMP10C24X Series H18U MEMBER