Altronix SMP5CT Series Operating and maintenance instructions

Power Supply Voltage Output Specifications: *
Output VDC Switch Position Max. Load DC
12VDC SW1 - Closed (Fig. 1b, pg. 3) 4amp
24VDC SW1 - Open (Fig. 1b, pg. 3) 4amp
*Specified at 25˚ C ambient.
Installation Instructions:
The unit should be installed in accordance with The National Electrical Code and all applicable Local Regulations.
1. Mount the unit in desired location.
2. Set SW1 on the power supply board to the desired DC output voltage
(Power Supply Voltage Output Specification Chart).
3. Connect AC power to terminals marked [L & N], connect ground to terminal marked [G] (if used).
Use 18 AWG or larger for all power connections (Battery, DC output).
Use 22 AWG to 18 AWG for power limited circuits (AC Fail/Low Battery reporting).
SMP5CTX - 1 - - - - .95 / .5 4 13.5”H x 13”W x 3.25”D
SMP5PMCTX - 1 - - - x .95 / .5 4 13.5”H x 13”W x 3.25”D
SMP5PMCTXX - 1 - - - x .95 / .5 4 15.5”H x 12”W x 4.5”D
SMP5PMP4 PD4 4 x - 3.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D
SMP5PMP4CB PD4CB 4 - x 2.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D
SMP5PMP8 PD8 8 x - 3.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D
SMP5PMP8CB PD8CB 8 - x 2.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D
SMP5PMP16 PD16W 16 x - 3.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D
SMP5PMP16CB PD16WCB 16 - x 2.5 x .95 / .5 4 13.5”H x 13”W x 3.25”D
Altronix
Model Number
Accessory Power
Distribution
Module(s)
Number of Outputs
Fused Outputs
PTC Outputs
Individual Output
Rating (amp)
115VAC/230VAC
Input Current (amp)
12/24VDC Total
Output Current (amp)
Enclosure Dimensions
SMP5CTX Series Power Supply Configuration Reference Chart:
Overview:
These units will convert a 115VAC or 230VAC, 50Hz/60Hz input, into a regulated 12VDC or 24VDC output up to 4
amps of continuous load current (see specifications).
Specifications:
• Universal 115/230VAC input.
• Maximum charge current .5 amp.
• Filtered and electronicallyregulated outputs.
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when
ACfails (zero voltage drop).
• AC input and DC output LED indicators.
• Short circuit and thermal overload protection.
• Complete with power supply, power distribution module
(when applicable), enclosure, cam lock & batteryleads.
• Power on-off switch.
Supervised Models Only:
• AC fail supervision (form "C" contacts).
• Low battery supervision (form "C" contacts).
- 1 -
SMP5CTX Series
Supervised

4. Connect devices to be powered:
a. For Power Supply Board connect to terminals marked [– DC + ].
b. For Power Distribution Module(s) connect devices to be powered to terminal pairs 1 to 4 marked
[1P & 1N thru 4P & 4N] (Fig. 2, pg. 4) or 1 to 8 marked [1P & 1N thru 8P & 8N] (Fig. 3, pg. 4) or 1 to 16 marked
[1P & 1N thru 16P & 16N] (Fig. 4, pg. 4) carefully observing correct polarity.
Note: Measure output voltage before connecting devices. This helps avoid potential damage.
*Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board. When servicing the unit,
AC mains should be removed.
5. When using stand-by batteries, they must be lead acid or gel type. Connect battery to terminals marked [– BAT +]
(battery leads included). Use two (2) 12VDC batteries connected in series for 24VDC operation.
Note: When batteries are not used a loss of AC will result in the loss of output voltage.
6. Connect appropriate signaling notification devices to AC Fail & Low Bat supervisory relay outputs
marked [NC, C, NO] (Fig. 1a, pg. 3).
LED Diagnostics:
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition
ON OFF Loss of AC, Stand-by battery supplying power
OFF ON No DC output
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
Terminal Identification:
Terminal Function/Description
Legend
L, G, N Connect 115V
AC/230VAC to these terminals:
Lto Hot, N to Neutral, G to ground (if used).
– DC + 12VDC / 24VDC @ 4 amp continuous non-power limited output.
AC FAIL Used to notify loss of AC power, e.g. connect to audible device or alarm
NC, C, NO panel. Relay normally energized when AC power is present.
Contact rating 1 amp @ 120VAC / 28VDC
LowBattery Used to indicate low battery condition, e.g. connect to alarm panel.
NC, C, NO.Relaynormally energized when DC power is present.
Contact rating 1 amp @ 120VAC / 28VDC
Lowbatterythreshold:
12VDC output threshold set @ approximately 10.5VDC,
24VDC output threshold set @ approximately 21VDC.
–BAT + Stand-by battery connections. Maximum charge rate .5 amp.
PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module
Terminal Legend Function/
PD4/PD4CB PD8/PD8CB PD16W/PD16WCB Description
1P to 4P 1P to 8P 1P to16P Positive DC power outputs.
1N to 4N 1N to 8N 1N to 16N Negative DC power outputs.
- 2 -

Power
Distribution
Module(s)
CAUTION: De-energize unit prior to servicing. For continued protection against fire hazard
replace fuse with the same type and rating 5A, 250V.
Green
Lead
Wire
Strap
(from
Enclosure
to Door)
115/230VAC
power
mains
INPUT
LOW BAT
NC C NO NC C NC
AC FAIL
SW1:
24V - OPEN
12V - CLOSED
CAUTION: When power supply board is set for 12VDC use only one (1) 12VDC
stand-by battery.
Keep power limited wiring separate from non-power limited. Use minimum .25" spacing.
12VDC Rechargeable Battery
(optional)
12VDC Rechargeable Battery
(optional)
L G N
OFF ON
OPEN - 24VDC
CLOSED - 12VDC
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT + --- DC +
AC DC
5A 250V
Fig. 1
- 3 -
Fig. 1a
Fig. 1b

INPUT
LED
1P, 2P,3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
F1
F1
F2 F3 F4
COMMON POWER OUTPUTS
1P 1N 2P2N 3P 3N 4P 4N
DC Output to devices From Power Supply
Board
(Factory Installed)
Used on
PTC Models
N
C O M M O N P O W E R O U T P U T S
P
FU S E D P O W E R O U T P U T S
1 2 3 4 5 6 7 8
1
D1
INPUT
R 1 LED
DC Output to devices From Power Supply
Board
(Factory Installed)
Fig. 2 Fig. 3
Power Distribution Module(s):
common
outputs
protected
outputs
P
N
NPS
XFMR Input
12345678
910 11 12 13 14 15 16
PN
3.5A 250V
For continuous protection against risk of fire
replace fuses with same type and rating.
Used on
PTC Models
Fig. 4
- 4 -

5.10"
6.5625"
3.25"3.25"
5.10"
5.10"
3.25"
1.00"10.50"1.00"
1.00" 1.00"
1.40"
1.20"
1.40"
1.20"
0.75"
0.75" 11.00"
12.50"
3.25"
0.9375"
0.9375"
1.40" 4.85" 4.85" 1.40"
1.20"
Bottom
Top
RightLeft
Enclosure Dimensions for:
• SMP5PMCTX • SMP5PMP4 • SMP5PMP4CB
• SMP5PMP8 • SMP5PMP8CB • SMP5PMP16 • SMP5PMP16CB
13.5”H x 13”W x 3.25”D
Enclosure accommodates up to two (2) 12VDC/7AH batteries.
Also available to accommodate up to two (2) 12VDC/12AH batteries (please contact Altronix).
- 5 -

- 6 -
12.230"
15.500"
1.100"
0.910"
1.100"
0.910"
0.790"
1.100"
1.500"
1.250"
5.000"
1.250"
1.500"
4.615"
4.615"1.500"
1.750"
1.500" 4.615"
4.615"1.500"
1.750"
4.500" 4.500"
1.250"
1.500"
5.000"
2.000"
2.000"
1.250"
1.375"
1.125"
Enclosure Dimensions for:
• SMP5PMCTXX
15.5”H x 12”W x 4.5”D
Enclosure accommodates up to two (2) 12VDC/12AH batteries.

- 7 -
Notes:

Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
140 58th Street, Brooklyn, NewY
ork 11220 USA, 718-567-8181, fax: [phone]
web site: www.altronix.com, e-mail: [email protected], Made in U.S.A.
IISMP5PMCTX - Rev. 093003 H02J
-8-
MEMBER
Notes: