Altwork TruVue Quick setup guide

TruVue Assembly and Use

TruVue - VCS
Video Conferencing Station
Product Details:
Lighting solution and webcam mounting system designed to attach
tomost monitors with an integrated VESA mount including monitors
on Altwork Stations Includes:
Mounting frame and hardware:
•Attaches to monitors with standard 75x75 and 100x100 VESA
screw locations
•(4) M4 mounting screws for mounting to your Altwork Station of
other VESA mount
•Includes P2 screwdriver for assembly (No other tools required)
•Lighting system with 2 LED panels and manual reset/control switch
Light Panels
•Source type light: LED
•LED type: “2835”
•LED bulbs: 240 pcs (per panel)
•LED panel size 6-1/4” x 9”
•Dimmable from 0-100%
•Color temperature: 2700K-5700K
•Impute power: AC100-240 VAC 50/60 Hz
•Out power: 42W (per panel)
Lighting remote:
•Turns lights on/off (Separately or together)
•Adjusts brightness warm to cold (Separately or together)
•Adjusts light intensity (Separately or together)
•(2) AAA batteries (US only)
Webcam Mount:
•Designed to work for all standard webcams
•Webcam mounts with standard 1/4-20 screw or adhesive tape
(included)
•6” Webcam vertical travel from top of screen
•Retracts out of view above monitor
•Flips down for desk view
WARNING!
•The power cord plug should be firmly inserted in the socket, and the power plug
should be pulled out after use to prevent electric shock and fire. The lights can not be
controlled fully when the battery power of the remote control in insufficient. Please
replace remote battery in time.
•Do not pull out the plug by pulling the power cord. Be sure to hold the plug firmly and
pull out of the socket.
•Do not pinch or kink the power cord during adjustment of the lights.
•Do not use when the power cord is damaged, or the plug is worn.
•Don’t spray or wash the product with water, and do not place it in a wet and easily
splashed place, so as to avoid affecting the electrical insulation performance of the
product.
Packing List
1. Frame with Lights
2. VESA Mount Brackets
3. Slides
4. Camera Mount Assembly
5. Hardware Kit
6. Remote
5
4
3
1
6
2

Use M4 x 14MM screws to attach the bracket to the back
of the monitor to the VESA mount threads as shown.
(2) VESA Mount Brackets
(4) M4 x 14mm flat-head screws
TruVue - VCS
Attach Brackets to Monitor with VESA Mount

TruVue - VCS
Attach to Monitor with VESA Mount (Over Existing Mount)
Remove existing screws from
left side of monitor mount. Remove existing screws from
right side of monitor mount.
Use M4 x 20mm flathead screws
to mount the bracket to the back
of the monitor through the VESA
mount as shown.
Attach the right side bracket
(2) VESA Mount Brackets
(4) M4 x 20mm flat-head screws

(2) Slides
(4) M4 x 12mm pan-head screws
(4) Large washers
Use M4 x 12mm pan-head screws to attach Slides to
VESA Mount Brackets with screw countersink hole at
top facing out and notch facing the monitor as shown.
(Start with the slides all the way down on the screws)
TruVue - VCS
Attach Slides to VESA Mount Brackets

Use M4 x 10mm flat-head screws to attach the bar of
the Frame to the Slides as shown.
(1) TruVue Frame
(2) M4 x 10MM flat-head screws
TruVue - VCS
Attach Frame to Slides

Loosen (4) screws to slide the Frame up so
that the bar is parallel to and just above the top
of the monitor as shown, then re-tighten.
TruVue - VCS
Adjusting the Frame to top of Monitor

Use the M4 x 16mm pan-head screw and small washer to attach the
Camera Mount to the Frame.
Make sure to adjust the location far enough forward to avoid hitting the
screen with the Camera Mount when deployed.
(1) Camera Mount Assembly
(1) M4 x 16MM pan-head screw
(1) Small washer
TruVue - VCS
Attachment Camera Mount to VCS Frame

1. Remove (3) clamps from Camera Bar
2. Loosen both thumb screws
3. Remove Camera Bar from Slide Block
Note: Thumb nuts and plastic block may need to
be removed for larger connectors to be installed
through the block.
TruVue - VCS
Attaching Camera to VCS Mount

Picture of screws and foam
tape
(1) ¼-20 x 1/4”
(1) Alt ¼-20 x 3/8”
(1) Alt Adhesive Tape
1. If the camera has a ¼-20 thread
mounting option,
2. select the correct length screw 1/4”
or 3/8” from the Hardware Kit.
3. Attach the camera to the Mount
through the hole that allows the
camera full range of adjustment.
1. If the camera does not have a ¼-20 thread mounting option,
select the Adhesive Tape from the Hardware Kit.
2. Make sure the surface of the Camera and Mount are clean and
free of oils then apply Tape to the Camera Mount.
3. Attach the Camera to the Mount onto the tape in a location
that allows the camera full range of adjustment.
TruVue - VCS
Attaching Camera Mount

Picture of wire in Pivot
Guide
Note: Third Wire Stop can be
used at an optional point as a
preset Stop for the camera
position in front of the screen.
1. Start with the camera facing down
2. Make sure that the wire is not pulling the back of the camera, press the wire into the groove of the Camera Bar from bottom to top.
3. Attach the Wire Stops at the bottom and top of the Camera Bar as shown
4. Thread cable through the Pivot Guide at the rear of the assembly
TruVue - VCS
Camera Wire Management
Note: Thumb nuts and
plastic block may need to
be removed for larger
connectors to be installed
through the block.

Picture of wire in Pivot
Guide
TruVue - VCS
Camera Mount Adjustment

Loosen thumbscrew before adjusting light panels.
Retighten after the light is in the desired position.
TruVue - VCS
Light Panel Adjustment

Pointing the remote
directly at a single light as
shown will allow for
independent control.
Pointing the remote
between the two lights as
shown will allow for dual
control.
The Manual Switch can be used to cycle through
four different preset lighting conditions by
switching off and on repeatedly
Less
Bright
Color
Temp -
Color
Temp +
More
Bright
ON/OFF
TruVue - VCS
Light Panel Remote Control
WARNING!
•Use care to install the batteries properly.
•Improperly installed batteries could
discharge rapidly and overheat.
Note: Reset and Resync Option:
If the light panels are ever out of sync and it becomes
difficult to use the remote to re-sync them, turn of the
power switch for at least (6) seconds before switching
back on. This should bring both lights back on in sync
with each other. If more than one TruVue is set up in the
same room, the switch can be turned off to prevent
overlapping controls when not in use.

TruVue - Desk Stand
Desk Stand Assembly
Packing List:
1. Base Plate
2. Upright (Left)
3. Upright (Right)
4. (6) M4 x 10MM Screws
3
1
2
4

TruVue - Desk Stand
Attaching Uprights to Base
If using a Monitor with standard
width stand or using the Laptop
Tray, use the set of holes that
are closer together.
If using a Monitor with wider
stand (Like Microsoft Surface)
use the set of holes that are
farther apart.
Attach Left side Upright to plate
with (3) M4 x 10mm screws.
Attach Right side Upright to plate
with (3) M4 x 10mm screws.
Attach the Uprights with groves facing in and flat
sides with screw holes at top facing forward.

TruVue - Desk Stand
Attaching the VCS Slides to Uprights
Attach VCS Slides to Uprights with M4 x 12MM
pan-head screws and large washers.
Make sure that the notch at the top of the Slides is
facing forward as shown.
(2) Slides
(4) M4 x 12MM pan-head screws
(4) Large washers

Note that the closer holes are for most monitors and
Laptop Tray and the wider holes are for monitors with
wider stands such as Microsoft Surface.
TruVue - Desk Stand
Attaching VCS Frame to Slides
Use M4 x 10mm flat-head screws to attach the bar
of the Frame to the Slides as shown.
(1) TruVue Frame
(2) M4 x 10MM flat-head screws

TruVue - Desk Stand
Adjusting VCS Frame to Top of Monitor
Loosen (4) screws to slide the Frame
up so that the bar is parallel to and
just above the top of the monitor as
shown, then re-tighten.

TruVue - Laptop Tray
Laptop Tray Assembly
3
1
2
4
Packing List:
1. Laptop Plate
2. Bracket (Left)
3. Bracket (Right)
4. (4) M4 x 8MM flat-head screws