Alula RE606 User manual

RE606 Tilt Sensor is a full-featured security transmitter
typically used to sense the tilt of overhead garage
doors and windows. It will alarm when the sensor is
tilted more than 45 degrees.
Features
• Industry-leading wireless range and battery life
• Secure encrypted wireless transmissions
• 5-year warranty
Enroll by placing the panel into wireless enrollment
mode and then removing the cover to send an
enrollment signal from the sensor. Alternatively,
the sensor can be enrolled by scanning its bar
code using the Connect+ Installer App or by
entering its 8-character serial number on the
interactive service provider’s web portal.
Install by mounting the sensor to the inside of
a door or window using the mounting screw
locations. For garage door installations, the
sensor should be mounted to the top panel of the
overhead door. CE installations must use a cover-
securing screw.
Tilt Detection occurs when the
sensor exceeds a 45 degree angle.
If the sensor rotates further than
135 degrees, it is likely to remain in
a non-alarm state. For best results,
the sensor should rotate within 90
degrees to ensure an alarm state
occurs.
RE606 Tilt Sensor
Connect+™Encrypted
I
N
S
T
A
L
L
G
U
I
D
E
I
Mounting
Screw
Holes
Cover-Securing
Screw Hole
Use the panel installation guide to verify proper system setup.

WARRANTY
Alula will replace products that are defective in their rst ve (5)
years.
TRADEMARKS
Alula and Connect+ are trademarks owned by Alula Holdings, LLC.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE606
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could
void the user’s authority to operate this equipment.
FCC ID: U5X-RE606-CE
CE DECLARATION OF CONFORMITY
Hereby, Alula declares that this RE606-CE is in compliance with the
essential requirements and other relevant provisions of directive
1999/5/EC.
(This declaration can be translated to other languages via a myriad
of translation tools found on the Internet.)
Specications
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.25 x 1.40 x 1.05 inches (8.3 x 3.6 x 2.7 cm)
1.90 ounces (54 grams)
#4 or #6 screws (not provided)
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
433.92 MHz
One Panasonic CR123A
10 to 15 years
3.0 VDC (Nominal), 2.2 VDC (Low)
20 mA (Maximum), 0.6 uA (Quiescent)
Cover Tamper, Low Battery, Supervision
Certication
RE606
RE606-CE
FCC, IC
EN50131-2-6, EN 60950-1, EN 300 220, EN 301 489,
CE Security Grade 1, CE Environmental Class 2, RCM
Specications subject to change without notice.
Pro Tips
3M VHB Tape works great for mounting if the surface is properly prepared and rm
pressure is applied for over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50 °F
47-0019-08 • REV A • 2018-03-06
Tech Support Line • (888) 88-ALULA • [phone]
alula.net