Alula RE607 User manual

RE607 Outdoor Door/Window Sensor is a full-featured
security transmitter with industry-leading wireless range
and battery life. It is designed to sense the opening and
closing of gates, sheds, and other outdoor open/close
applications. An alarm signal will be transmitted when the
magnet is pulled away from the sensor, or when an external
contact is opened.
Features
• Industry-leading wireless range and battery life
• Wide magnetic gap distance
• Two built-in external contact zones
• Secure encrypted wireless transmissions
• IP67 waterproof enclosure rating
• 5-year warranty
Enroll by placing the panel into wireless enrollment mode
and transmitting an enrollment signal from the sensor.
Alternatively, the sensor can be enrolled by scanning its
bar code using the Connect+ Installer App or by entering
its 8-character serial number on the interactive service
provider’s web portal. External contacts can be added on
the interactive service provider’s web portal.
Install by rst attaching the mounting plate and magnet to
a door, window, or fence using screws (provided) or cable
ties (not provided).
Make sure to align the alignment marks on the sensor and
magnet when mounting. Finish by latching the sensor to
the mounting plate and tightening the cover-securing screw
to secure the sensor in place.
Use the panel installation guide to verify proper system setup.
RE607 Outdoor Door/Window Sensor
Connect+™Encrypted
I
N
S
T
A
L
L
G
U
I
D
E
I
Mounting Tips
• Face of mounting plate marked “Flat Mount” is to be
mounted against at surfaces (e.g. square wood post).
• Face of mounting plate marked “Pole Mount” is to be
mounted against round surfaces (e.g. fence post).
Options for sending an Enrollment Signal
• Remove the battery tab, OR
• Remove the cover to trip tamper
Alignment Marks
Cover-Securing Screw Hole
Mounting Screw Holes
Magnet

External Contacts can be installed by routing the wires through
the back of the enclosure. A thinned area in the enclosure must be
punched out with a screwdriver to allow the wires through. After
routing and connecting the wires, reseal the hole with silicone
caulk.
• Do not use end-of-line resistors.
• Wire contacts to one or both outside terminals using the
center terminal as a shared common.
• The sensor defaults to use normally closed contacts (alarm
condition when contact is open).
• To reprogram external inputs, set both externals to the
desired non-alarm state and restart (remove and reinstall
battery) the device 3 times while holding the tamper
switch.
Thinned area for external
contact wires
Removal Tamper is implemented by screwing the provided screw
with rubber washer through the removal tamper screw hole in the
base and into the mounting surface. Remove the battery for access
to the removal tamper screw hole.
Removal tamper
screw hole
Pro Tips
Metal installs should include pre-drilling holes before using
screws to secure the mounting plate and magnet.
Wireless performance is optimized when mounted near the
top of the gate or door in a vertical orientation.

Magnet Gap Specications
Non-Ferromagnetic Surface (e.g. Wood, Vinyl, etc.)
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
2.70 inches (6.86 cm)
2.80 inches (7.11 cm)
2.85 inches (7.24 cm)
3.50 inches (8.89 cm)
3.55 inches (9.02 cm)
3.27 inches (8.31 cm)
3.33 inches (8.46 cm)
Ferromagnetic Surface (e.g. Iron, Nickel, etc.)
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
1.90 inches (4.83 cm)
2.00 inches (5.08 cm)
2.05 inches (5.21 cm)
2.50 inches (6.35 cm)
3.00 inches (7.62 cm)
2.32 inches (5.89 cm)
2.37 inches (6.02 cm)
*Sensitivity can be adjusted by moving the magnet in
the closed position farther away from the sensor.
Z Axis
Y Axis
X Axis
X Axis

TRADEMARKS
Alula and Connect+ are trademarks owned by Alula Holdings, LLC.
Panasonic is a registered trademark owned by Panasonic
Corporation.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE607
WARRANTY
Alula will replace non-portable products that are defective in their
rst ve (5) years and all portable products in their rst two (2)
years.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could
void the user’s authority to operate this equipment.
FCC ID: U5X-RE607
Specications subject to change without notice
Physical
Housing Dimensions
Weight with Battery
Mounting Fasteners
Removal Tamper Fastener
3.3 x 1.3 x 2.8 inches (8.4 x 3.3 x 7.1 cm)
5.7 ounces (161.6 grams)
Four 1 inch stainless steel screws (provided)
One 11/4 inch stainless steel screw with rubber washer (provided)
Environmental
Operating Temperature
Maximum Humidity
Ingress Protection Rating
-40° to 158°F ( -40° to 70°C)
100% Relative Humidity (RH)
IP67
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
Max Wire Length on External
Contacts
433.92MHz
One Panasonic®CR123A Lithium Battery
10 years
3.0 VDC (Nominal), 2.2 VDC (Low)
20 mA (Maximum), 0.6 uA (Quiescent)
Cover Tamper, Removal Tamper, Low Battery, Supervision
7.5 feet
Certication
RE607 FCC, IC
Specications
47-0060-00 • REV A • 2019-01-04
Tech Support Line • (888) 88-ALULA • [phone]
alula.net
01