Alula RE110P User manual

Ceiling
Floor
The Indoor Motion Sensor alarms when motion is sensed
or when the external contact is opened. It is battery
powered and requires no installation tools. A Pyroex™
sensor with HighBar™signal processing allows for industry-
leading pet immunity and catch performance.
Features
• Industry-leading pet immunity and catch performance
• Supports both motion zone and an external contact zone
• Mountable on walls or in corners
• 5 year warranty
Enroll by placing the panel into learn mode and then tripping
the tamper switch. Enroll the external contact zone by
inserting the battery with the external contact closed.
Install using the included 3M™ VHB™ tape to adhere the
motion sensor on a wall or in a corner. The tape should
be applied to the back when wall mounting or to the
back bevels when corner mounting. Alternatively, screw
mounting can be done by punching out the screw mounting
holes.
Installation Tips
• Mount 7.5 to 9.5 feet from the oor for an
optimal balance between catch performance
and pet immunity.
• Remove the cover and circuit board before
trying to punch out the screw mounting holes.
• Ensure the bug foam stays intact and
snug around the IR sensing element when
re-installing the circuit board.
External Contact
• Use a normally-closed contact because the
motion sensor will transmit an alarm when it
sees the external contact open.
• Do not use end-of-line resistors.
Suggested Group Types
• Use Interior Follower for the motion zone
• Use Perimeter for the external contact zone
Mounting Screw Holes
Verify proper enrollment and operation using your control panel’s installation manual.
I
N
S
T
A
L
L
G
U
I
D
E
I
Resolution Compatibles
RE110P Indoor Motion Sensor
-Pet Immune Interlogix®Compatible

Pro Tips
Walk test mode is entered by pressing the motion
sensor’s tamper button. The walk test lasts three
minutes.
Walk Test Operation
• The walk test LED turns on when motion
is sensed.
• The motion sensor performs a
re-calibration after each activation. The
re-calibration takes about 30 seconds.
The sensor will NOT sense motion
during the re-calibration.
• Wireless transmissions are sent for each
detection, so walk test mode can also
be used to test the panel.
3M™ VHB™ tape works great if the surface is
properly prepared and rm pressure is applied for
over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface
temperature is above 50 °F
Motion lockout is active for three minutes after a motion event is detected. Motion
events will be ignored during the motion lockout period.
Motion sensitivity can be adjusted by the sensitivity jumper on the circuit board.
• Jumper Installed (lower sensitivity): Detects person in 3 to 5 steps.
Increases pet immunity, usually for security applications.
• Jumper NOT Installed (higher sensitivity): Detects person in 2 to 4 steps.
Usually for occupancy applications.
Pet immunity is optimized when the motion sensor is mounted at 7.5 to 9.5 feet high
and aimed away from house features that could allow pets to be high in the detection
eld (e.g. stairs, counter tops, tall furniture).
Motion catch performance is best when the motion sensor is positioned so a person
would typically walk across the front of the motion sensor instead of directly toward
the motion sensor.
Motion Detection Tips
• Provide a clear line-of-sight to the monitored area and remember that glass
blocks infrared energy.
• Aim away from windows and sunlight.
• Aim away from air conditioners, heaters or heating/cooling vents.
Walk Test LED
Cover Tamper Switch
Battery
Bug Foam IR Sensing Element
Sensitivity
Low - Jumper ON
High - Jumper OFF
External Contact
7.5ft
0
0 10ft 20ft 30ft 40ft
3.2ft

Accessories
Gimbal mount (RE019 and RE019-10) allows the motion sensor direction to be adjusted
after mounting on a wall.
Horizontal beam lens (RE020) has less look-down which results in increased pet
immunity.
Specications
Side eld of view for a mounting height of 7.5 feet
0
10ft
20ft
30ft
40ft
Top eld of view
010ft 10ft20ft 20ft30ft 30ft
7.5ft
3.2ft
010ft 20ft 30ft 40ft
3.2ft
9.5ft
6.4ft
010ft 20ft 30ft 40ft
Side eld of view for a mounting height of 9.5 feet

47-0005-01 • RevE • 2020-02-03
Tech Support Line • (888) 88-ALULA • (888)-882-5852
alula.net
WARRANTY
Alula will replace products that are defective in their rst ve (5)
years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE110
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could void
the user’s authority to operate this equipment.
FCC ID: U5X-RE110
TRADEMARKS
Alula is a trademark owned by Alula Holdings, LLC.
“Interlogix” is a trademark owned by United Technologies Electronic
Controls Inc.
Alula products will function with Interlogix systems. However, no
Alula product is produced by, endorsed by, or is ofcially associated
with Interlogix. Alula recommends verifying proper enrollment and
operation, per control panel installation instructions, at installation.
3M and VHB are trademarks owned by 3M Company.
Panasonic is a trademark owned by Panasonic Corporation.
Pyroex and Highbar are trademarks of Sun Chemical Corporation.
Specications
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.50 x 2.40 x 1.70 inches (8.9 x 6.1 x 4.3 cm)
3.2 ounces (91 grams)
3M™ VHB™ Tape or Screws (both provided)
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Pet Immunity
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Optimal Mounting Height
Transmitted Indications
Maximum Wire Length on
External Contact
319.5 MHz
Two 60-pound dogs or one 85-pound dog
One Panasonic®CR123A
6 to 8 years
3.0 VDC (Nominal), 2.2 VDC (Low)
30 mA (Maximum), 20 uA (Quiescent)
7.5 to 9.5 feet (2.3 to 3.0 m)
Cover Tamper, Low Battery, Supervision
7.5 feet
Certication
RE110P FCC, IC
Specications subject to change without notice