Alula RE611P User manual

The Pet Immune Indoor Motion Sensor alarms when
motion is sensed. It is battery powered and requires no
installation tools.
Features
• Five year battery life
• Quick peel and press mounting
• Mountable on walls or in corners
Enroll by placing the panel into wireless enrollment mode
and then sending an enrollment signal from the sensor.
Alternatively, the sensor can be enrolled by entering its
8-character serial number in the AlulaConnect™ portal.
Options for sending an Enrollment Signal
• Remove the battery tab
• Remove the cover to trip the tamper
Install using the included mounting tape to adhere the
motion sensor on a wall or in a corner. Alternatively,
screw mounting can be done by punching out the screw
mounting holes and using the included screws to mount
in the desired location.
Installation Tips
• Mount 7.5 feet from the oor.
• Remove the cover before trying to punch
out the screw mounting holes.
• It is recommended to ensure there is a tight
seal around the mounting holes to prevent
bugs from entering the sensor and causing
false alarms.
During normal operation the LED will not turn on even
if motion is detected. This is done to maximize battery
life. Furthermore, when motion is detected and a signal
is transmitted to the panel, the sensor will not transmit
again for a period of three minutes.
Use the panel installation guide to verify proper system setup.
RE611P Pet Immune Indoor
Motion Sensor, Alula Encrypted
I
N
S
T
A
L
L
G
U
I
D
E
I
Mounting Screw Holes
Mounting Screw Holes
Cover Securing Screws

Pro Tips
Walk test mode is entered by removing the battery for
10 seconds and re-inserting the battery. The red LED
will begin to ash indicating that the motion sensor
is warming up. After 45 seconds, the LED will stop
ashing which indicates the motion sensor is ready
to detect motion. The LED will illuminate each time
motion is detected. Once the LED goes out, the sensor
is ready to detect motion again. Walk test mode ends
after 15 minutes. It is recommended that the RE611P
PIR is tested monthly to ensure proper function.
Mounting tape works great if the surface is properly
prepared and rm pressure is applied for over 10
seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature
is above 50 °F
Motion sensitivity can be adjusted by the sensitivity jumper on the circuit board.
• For standard sensitivity motion detection with pet immunity leave the jumper
in the default setting (on).
• Remove the jumper if increased sensitivity to movement is desired.
Pet immunity is optimized when the motion sensor is mounted at 7.5 feet high and
aimed away from house features that could allow pets to be high in the detection eld
(e.g. stairs, counter tops, tall furniture).
Motion catch performance is best when the motion sensor is positioned so a person
would typically walk across the front of the motion sensor instead of directly toward
the motion sensor.
Motion Detection Tips
• Provide a clear line-of-sight to the monitored area and remember that glass
blocks infrared energy (PIR = Passive InfraRed).
• Aim away from windows and sunlight.
• Aim away from air conditioners, heaters or heating/cooling vents.
Tamper Switch
Sensitivity Jumper
Battery

Side eld of view for a mounting height of 7.5 feet
Top eld of view
Specications

TRADEMARKS
Alula and AlulaConnect are trademarks owned by Alula Holdings,
LLC. All trademarks, logos and brand names are the property of
their respective owners. All company, product and service names
used in this document are for identication purposes only. Use of
these names, trademarks and brands does not imply endorsement.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could
void the user’s authority to operate this equipment.
FCC ID: XQC-WST740
Specications
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 9863B-WST740
47-00035 • Rev A • 2023-05-05
Tech Support Line • (888) 88-ALULA • [phone]
alula.com
01
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.5 x 2.5 x 1.8 inches (8.9 x 6.4 x 4.6 cm)
3 ounces (85 grams)
Mounting Tape or Screws (both provided)
Environmental
Operating Temperature
Maximum Humidity
32°F to 120°F (0°C to 49°C)
95% non-condensing relative humidity
Sensor Specications
Frequency
Pet Immunity
Replacement Battery
Battery Life
Battery Voltage
Optimal Mounting Height
Transmitted Indications
433.92 MHz
Up to a maximum of 85 lbs
One Panasonic CR123A
5 years
3.0 VDC (Nominal)
7.5 feet (2.3 m)
Cover Tamper, Low Battery, Supervision
Certications
RE611P FCC, IC
Specications subject to change without notice