Alula RE605 User manual

The RE605 Temp Sensor is used to detect freeze and
overheat conditions. The sensor will alarm when the
temperature trip points are reached.
Features
• Indicates freeze and overheat warnings
• Industry-leading wireless range and battery life
• Secure encrypted wireless transmissions
• 5-year warranty
Enroll by placing the panel into wireless enrollment mode
and then sending an enrollment signal from the sensor.
Alternatively, the sensor can be enrolled by scanning
its bar code using the Connect+ Installer App or by
entering its 8-character serial number on the interactive
service provider’s web portal.
Options for sending an Enrollment Signal
• Remove the battery tab, OR
• Remove the cover to trip tamper
Install by mounting the sensor in the desired location
using two #4 or #6 screws. An optional cover-securing
screw is included. Alternatively, the sensor can also be
installed using 3M VHB tape.
Freeze or Heat alarms are transmitted when the
temperature trip points are reached.
Temperature Trip Points
• Heat alarms when over 100°F (38°C)
• Heat restores when under 97°F (36°C)
• Freeze alarms when under 45°F (7°C)
• Freeze restores when over 48°F (9°C)
Use the panel installation guide to verify proper system setup.
Mounting Screw Holes
RE605 Temperature Sensor
Connect+™Compatible
I
N
S
T
A
L
L
G
U
I
D
E
I
Cover-Securing Screw Hole

WARRANTY
Alula Holdings, LLC will replace products that are defective in their
rst ve (5) years.
TRADEMARKS
Alula and Connect+ are trademarks owned by Alula Holdings, LLC.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE301
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by the Alula
Holdings, LLC could void the user’s authority to operate this
equipment.
FCC ID: U5X-RE301
CE DECLARATION OF CONFORMITY
Hereby, Alula Holdings, LLC declares that this RE605-CE is in
compliance with the essential requirements and other relevant
provisions of directive 1999/5/EC.
(This declaration can be translated to other languages via a myriad
of translation tools found on the Internet.)
47-0018-08 • REV A • 2018-03-06
Tech Support Line • (888) 88-ALULA • [phone]
alula.net
Specications
Specications subject to change without notice
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.30 x 1.40 x 1.10 inches (8.3 x 3.6 x 2.7 centimeters)
1.90 ounces (54 grams)
#4 or #6 screws (not provided)
Environmental
Operating Temperature
Maximum Humidity
0°F to 120°F (0°C to 49°C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
433.92 MHz
One Panasonic CR123A
10 years
3.0 VDC (Nominal), 2.2 VDC (Low)
20 mA (Maximum), 0.6 uA (Quiescent)
Cover Tamper, Low Battery, Supervision
Certication
RE605
RE605-CE
FCC, IC, RCM
EN 60950-1, EN 300 220, EN 301 489, CE
Pro Tips
3M VHB Tape works great if the surface is properly prepared and rm pressure is applied
for over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50°F
02