ALW LIGHTPLANE 2 User manual

A1035 22nd Avenue, Unit 1 nOakland, CA 94606 P510.489.2530 [e-mail] Walwusa.com
INSTALLATION INSTRUCTIONS
LIGHTPLANE 2
LP2SMB/W | Surface and Wall Mount | LED

LP2 Surface/Wall Installation Guide 2 of 12 102-000027 - IG121818-A.0
Safety & Warnings!
1. Read all instructions.
2. Install in accordance with national and local electrical code regulations.
3. This product is intended to be installed and serviced by a qualied, licensed electrician.
4. Turn off electrical power before installing or servicing xture in any way.
5. Do not install in wet locations. For dry and damp use only.
6. Turn off electrical power before installing or servicing xture in any way.
7. To reduce the risk of re and overheating, make sure all connections are tight.
8. This product is suitable for continuous row mounting.
1. Lisez toutes les instructions.
2. Installez conformément à la réglementation du code électrique national et local.
3. Ce produit est destiné à être installé et entretenu par un électricien agréé qualié.
4. Coupez l’alimentation électrique avant d’installer ou de réparer le luminaire de quelque manière que
ce soit.
5. Ne pas installer à l’extérieur ou dans des endroits humides. Pour une utilisation en intérieur et sec
seulement.
6. Coupez l’alimentation électrique avant de évoluer le système d’éclairage en aucune façon.
7. Pour réduire le risque d’incendie et de surchauffe, assurez-vous que toutes les connexions sont bien
serrées.
8. Ce produit convient au montage en ligne continue.
Attention!
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior
to installation or servicing.

LP2 Surface/Wall Installation Guide LP2 Surface/Wall Installation Guide 3 of 12 102-000027 - IG121818-A.0
Table of Contents
Troubleshooting 11
Wiring Diagrams 12
Installation 5
Prepare Ceiling 5
Connecting Multiple Sections 10
SMB - Surface/Back Mount 5
Wall Mount 7
Luminaire Overview 4
Diagrams 4
Components 4
Parts (by others) 4
Tools Required 4
Quick Specs 4

LP2 Surface/Wall Installation Guide 4 of 12 102-000027 - IG121818-A.0
LUMINAIRE OVERVIEW
Drill
#2 phillips bit
Tools Required
Wire strippers
Input Voltage / Frequency:
See product label
Rated Power:
See product drawing
Ambient Temperature:
-4° – 120°F (-20° – 50°C)
Environment:
Dry and damp locations
Quick Specs
Junction Box (Optional)
Parts (by others)
Wood Screws, #10, 1.5”
long
Conduit/NM (non-metallic)
cable (or similar) if not using
J-Box
OPTIONAL HARDWARE COMPONENTS
Mounting Bracket
J-Box (Optional)
Blocking/Framing
To Building Power (High Voltage)
Wall Mount Plate (Optional)
Fixture Body
(w/ Integrated LED Driver)
Heatsink/Reector
Lens
5/64” Hex Key (for Joining)
1/8” Hex Key (for Joining)

LP2 Surface/Wall Installation Guide 5 of 12 102-000027 - IG121818-A.0LP2 Surface/Wall Installation Guide
Installation: Prepare Ceiling
ELECTRICAL WIRING:
A
T
MUST
See nal/record drawings for mounting locations. Install
framing with consideration for alignment of wiring and
mounting locations.
1See Final/Record Drawings for Mounting Locations
SAMPLE DRAWING
ELECTRICAL WIRING:
A
T
MUST
Install Canopy J-Box (if using - sold separately) at power
feed location per nal/record drawing. Otherwise run
conduit/NM cable to powerfeed location.
2Install Canopy J-Box/Wiring
SAMPLE DRAWING
Carefully remove lens using suction cup or similar.
3Remove Lens
Remove heatsink/reector screws that attach to housing.
Set aside.
4Remove Heatsink/Reector Screws
Installation: SMB - Surface/Back
Mount
Remove heatsink/reector and hang over side of xture.
CAUTION: Do not apply excessive tension to wires.
5Remove Heatsink/Reector
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior to
installation or servicing.
!
DO NOT PINCH OR PUT EXCESSIVE TENSION ON
WIRES while joining sections or reattaching heatsink.

LP2 Surface/Wall Installation Guide 6 of 12 102-000027 - IG121818-A.0
Remove optional surface mount hardware if not using.
6Optional: Remove Surface Mount Hardware
Installation: SMB - Surface/Back
Mount (Cont.)
9Install Fixture to Ceiling/Framing
Afx xture to ceiling and framing using appropriate
hardware, ensuring xture is properly supported.
Re-install the heatsink/reector, as shown. CAUTION: Do
not pinch wires while reattaching!
10 Re-install Heatsink/Reector
7Connecting Multiple Sections (If Necessary)
Please see steps 28 through 33 for directions on
connecting multiple sections.
8Raise Fixture to Ceiling & Connect Wiring
Raise entire xture to ceiling, and connect wiring inside
xture. Refer to page 12 and record drawing to make
wiring connections. CAUTION: High Voltage Wiring —
Ensure Power is OFF prior to connecting wiring.
SHOCK HAZARD! May result in serious injury or death. Turn
power OFF at circuit breaker prior to installation or servicing.
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior to
installation or servicing.
!
DO NOT PINCH OR PUT EXCESSIVE TENSION ON
WIRES while joining sections or reattaching heatsink.

LP2 Surface/Wall Installation Guide LP2 Surface/Wall Installation Guide 7 of 12 102-000027 - IG121818-A.0
Installation: SMB - Surface/Back
Mount (Cont.)
Re-install heatsink/reector screws to attach back to
housing.
11 Re-install Heatsink/Reector Screws
Carefully re-install lens, ensuring lens sits properly within
Lens Clips.
12 Re-install Lens
Installation: Wall Mount
Carefully remove lens using suction cup or similar.
15 Remove Lens
WALL
ELECTRICAL WIRING:
A
WALL
T
MUST
1
AL
120V
MED/3000K
MED/3000K-0/10V/10%-EXT/R-AL-120V-NA
Follow steps 1-2 to prepare ceiling. (Install framing, J-Box,
if using, and wiring to J-Box or xture).
14 Prepare Ceiling
SAMPLE DRAWING
Remove heatsink/reector screws that attach to housing.
Set aside.
16 Remove Heatsink/Reector Screws
Turn breaker ON and ensure that xture operates as
intended and that there are no loose connections.
13 Turn Power On

LP2 Surface/Wall Installation Guide 8 of 12 102-000027 - IG121818-A.0
Installation: Wall Mount (Cont.)
21 Install Fixture Housing Directly to Wall/Framing
If not using mounting brackets, install xture directly to
framing/blocking, as shown.
If necessary, remove wall mount hardware.
18 Remove Wall Mount Hardware (If Necessary)
Remove heatsink/reector and hang over side of xture.
CAUTION: Do not apply stress to wires.
17 Remove Heatsink/Reector
19 Connecting Multiple Sections (If Necessary)
Please see steps 27 through 32 for directions on
connecting multiple sections.
20 Raise Fixture to Wall & Connect Wiring
Raise entire xture to wall, and connect wiring inside
xture. Refer to page 12 and record drawing to make
wiring connections. CAUTION: High Voltage Wiring —
Ensure Power is OFF prior to connecting wiring.
SHOCK HAZARD! May result in serious injury or death. Turn
power OFF at circuit breaker prior to installation or servicing.
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior to
installation or servicing.
!
DO NOT PINCH OR PUT EXCESSIVE TENSION ON
WIRES while joining sections or reattaching heatsink.

LP2 Surface/Wall Installation Guide LP2 Surface/Wall Installation Guide 9 of 12 102-000027 - IG121818-A.0
Installation: Wall Mount (Cont.)
Turn breaker ON and ensure that xture operates as
intended and that there are no loose connections.
Proceed to step 13 for lens installation.
26 Turn Power On
Re-install each heatsink/reector section. CAUTION: Do
not pinch wires while reattaching!
22 Re-install Heatsink/Reector
Re-install heatsink/reector screws to attach back to
housing.
23 Re-install Heatsink/Reector Screws
Carefully re-install lens, ensuring lens sits properly within
Lens Clips.
24 Re-install Lens
Ensure the lens is properly installed between the Lens
Clips.
25 Ensure Lens Sits Properly Between Lens Clips

LP2 Surface/Wall Installation Guide 10 of 12 102-000027 - IG121818-A.0
Connect wiring quick-connects between sections. Match
each color, as shown. NOTE: Color combinations may
vary.
32 Connect Wiring Between Sections
Tighten set screws to secure outer corner bracket to
joined section using a 1/8” hex key. Ensure each section
is properly aligned and that there are no gaps between
sections.
30 Tighten Set Screws on Outer Corner
Tighten joiner screws, as shown. Ensure each section is
properly aligned, and that there are no gaps between
sections.
31 Tighten Joiner Screws on Inner Corner
Installation: Connecting Multiple
Sections
Tighten joiner set screws, as shown, using a 5/64” hex key
for the sides and a 1/8” hex key for the bottom. Ensure
each section is properly aligned, and that there are no
gaps between sections.
28 Tighten Joiner Set Screws
29 Mitered Corners: Join Sections
Join sections together, as shown, ensuring correct align-
ment. See nal/record drawing for more details.
Loosen set screws and slide out joiner bracket halfway
to allow for joining. Join sections together, as shown,
ensuring correct alignment. See nal/record drawing for
more details.
27 Align and Join Sections Together