ALZA ID205G User manual

ID205G
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

3
Bind watch
1. download and install app
You can set up the watch through the VeryFitPro app for iOS or Android devices. The
steps are shown as follow:
Notes: The hardware platform f the equipment system shall meet requirements.
iOS 8.0 version or
above
Android 4.4 system or
above
Support Bluetooth 4.2
Correct operation: Scan
the QR code below or
download VeryFitPro APP
trough the mobile APP
store to pair with the
watch.
Wrong operation: Pair the
watch directly with the
Bluetooth in your mobile
phone’s settings.

4
2. Bind process
Notes:
•During binding process, VeryFitPro will prompt you to enable GPS and Bluetooth,
and authorize VeryFitPro to get access to the GPS on your mobile phone.
•iPhones will not prompt you with any information unless you complete Bluetooth
pairing on your ID205G watch in the built-in Bluetooth in your mobile phone after
binding.
1. Turn on the
Bluetooth and GPS on
your mobile phone
2. Find binding request
on the pull-down list on
the home page of the
APP
Select product model:
ID205G
Click “Ok“ to complete
binding.

2
Synchronous Data
In daily wear, the watch can detect all kinds of
product data. The user needs to connect the watch
with Bluetooth on the APP before synchronous
operation. The detailed operations are shown as
follows:
Open the mobile APP> swipe down the page> sync
prompt appears
Notes!
Please synchronize the data at least once within 7
days to avoid data loss at the watch end.

3
Instruction for Use
1. Charging schematic
Connect and charge the watch according to the picture. It needs to be charged to
activate the watch when it is started for the first time.
2. Wear/install
Wear Replace the strap
Tip: Wearing too loosely may affect the accuracy of heart rate data.
Wear the device a finger´s distance
Flip the switch and take out the
wristband Tightness of the wristband
to a comfortable position.
Flip the switch and take out the
wristband

4
Operating Instructions
1. Definition of key function
Short press the right key: Return to previous interface
2. Watch dial switch
replacing the dial interface will appear after long pressing
the dial.

5
3. Main interface operation
Swipe the screen to enter different
interfaces (interactive interface tile
diagram)
Function Introduction
1. Icon function introduction
Status bar
Function list
interface
Notice bar
Data bar
Perform a heart rate test
to check your heart rate
data for the day.
Help you regulate your
breathing and Relax your
mood.
View, turn off or turn on
the alarm clock. You need
to add an alarm clock on
the mobile APP.
Control music play on
your mobile phone
(watch cannot store
music)
Have the timing and
countdown function.
Record recent sports.

6
Notes: For more functions (sleeping) and operation, please check the VeryFitPro
software of the mobile phone.
2. Start sports
Enter sports
Click the sports icon > select the sports type > enter the sports countdown
automatically
During sports
Pause sports: short press the right key
Resume sports: short press the right key
End sports
End sports: long press the right key > select the end button on the screen
Sport activity with GPS
Outdoor run, walk and cycling activities support GPS tracking. After selecting activity
device will start searching GPS signal. It is possible to skip searching GPS signal by
pressing arrow but activity will be using only accelerometer data which is not that
accurate as GPS positioning.
Special feature for Outdoor run with GPS - competitor
When you select GPS run, device will automatically start searching GPS signal. After
search is complete, you can press arrow and you will get to screen "Select a competitor".
You can choose pace which will be compared to your effort during activity. You will see
distance to your virtual competitor and comparison of your paces. Activity will
automatically start after pressing green sign when you select your pace or you can start
activity without this feature by clicking on red cross.
Automatic detection of activity
You can select automatic detection of activity in VeryFitPRo app.
Weather function allows you keep track of the weather in your city.
Because weather data is obtained through mobile phone network, it is
required to maintain the connection between the Watch and the phone
to timely update weather data.

7
3. Women’s health tracking
Display location: in the data bar Women’s health tracking
function, which is used for recording menstrual changes,
tracks individual menstrual cycle and predicts ovulation (it
needs to be enabled on the APP).

8
Product Parameters
Model
ID205G
Screen type
1.3-inch color
screen
Battery capacity
210mAh
Charging voltage
5V±0.2V
Charging time
About 2.5 hours
Battery life
5-7 days
Waterproof level
5ATM
Weight of product
35g
Operating
temperature
-10°C-45°C
Bluetooth version
BLE 4.2
Product frequency
2402-2480MHz
Max. transmission
power
consumption
0dBm
Cleaning and Maintenance
It is recommended to wear and maintain according to the following three points:
❶Keep the product clean;
❷Keep the product dry;
❸Do not wear it too tight.
Do not use household cleaners to clean the watch, but use the soap free detergent.
It is recommended to use alcohol to scrub stains that are not easy to remove.

9
Frequently Asked Questions
1. Mobile APP search for the watch failed
❶It is recommended to update VeryFitPro to the latest version.
❷It is recommended to close all programs, restart the Bluetooth, and then connect.
❸Confirm whether the mobile phone system meets Android 4.4 or IOS 8.0 or above.
2. The watch received no alerts, text messages or phone calls
❶You need to turn on the smart reminder function and the call reminder switch in the
APP and synchronize the watch.
❷The iPhone needs to be paired with the watch via Bluetooth. (Please check the
column of „Synchronous Data“ for details)
❸You need to keep your watch connected to Bluetooth.
3. Bluetooth is often disconnected
❶If the distance between the watch and the mobile phone is too far, the connection
effect of more than 7m Bluetooth is obviously weakened.
❷Whether there is shield between the watch and the mobile phone, the human body,
wearing metal jewelry, etc., will interfere with the Bluetooth connection signal.
❸Whether the Bluetooth function of the mobile phone is abnormal.
4. About data backup
The data of the watch is synchronized at least once every 7 days to the mobile phone
(the watch end only keeps the data of the last 7 days).
5. How to restart
Shutdown operation: Watch > set > shutdown—right-key restart
6. Do I need to keep my Bluetooth on when I wear my watch?
❶For the three functions, i.e. counting steps, sleeping and alarm clock, you do not need
to connect the watch to the mobile phone all the time. If you only need to wear a watch
when you exercise, you can connect the watch and your mobile phone to view the data
synchronously after the exercise.
❷For the functions of call alert, message alert, find the phone, you need to turn on the
mobile phone’s Bluetooth, and maintain the connection with the mobile phone.
More detailed questions can be answered with help and feedback in the APP.
Operation steps: VeryFitPro > > help and feedback

10
Safety and Product Information Notes
WARNING
Battery Warning
Do not disassemble, bore, or damage the battery. Do not disassemble the built-in
batteries of none-replaceable battery devices. Do not use sharp objects to remove the
battery.
Health Warning
If you are wearing a pacemaker or other implanted electronic devices, please consult
your doctor before using the heart rate monitoring strap.
The watch’s optical heart rate sensor glows green and flashes. If you suffer from
epilepsy or are sensitive to blinking light sources, please consult your physician if you
can wear this product.
The device tracks your daily activities through sensors. These data are intended to tell
you about your daily activities, such as steps, sleep, distance, heart rate and calories, but
may not be completely accurate.
The device, accessories, heart rate sensors and other relevant data are designed for
entertainment and fitness, not for medical purposes. They are not applicable to the
diagnosis, monitoring, treatment or prevention of any diseases or symptoms. The heart
rate data is for reference only. We are not responsible for any consequences caused by
any data deviation.
Cycling Warning
Please maintain good judgement at all times and ride in a safe manner. Make sure your
bike and hardware are properly maintained, and all components are properly installed.
Matters Needing Attention
Watch data needs to be kept once every 7 days to avoid data loss.
The watch has no waterproof effect on seawater, acidic and alkaline solutions, chemical
reagents and other corrosive liquid. The damage or defects caused by misuse or
improper use are not covered by the warranty.
Sports mode supports up to 6 hours of exercise at a time.
Avoid wearing the watch too tight in daily use. Please keep the parts of the watch
touching the dry skin.
When your heart rate is measured, keep your arm still during the test.

11
If you experience discomfort or skin irritation when wearing your smart watch, then we
recommend you to try cleaning your device. Sometimes residue or foreign materials
build up around your device and may aggravate your skin. It’s also possible that you are
not wearing the watch correctly. We recommend making sure to clean and adjust your
watch regularly for a more comfortable fit.
Caution:
If you experience skin irritation when wearing your watch, please refrain from wearing,
and wait two to three days to see if your symptoms ease. If symptoms persist or worsen,
please consult a physician.
If you have eczema, allergies or asthma, you may be more likely to experience a skin
irritation or allergy from a wearable device.
This device complies with part 15 the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications no expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment. This equipment
has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

12
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you
need repair or other services during the warranty period, contact the product seller
directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for
which the claimed claim may not be recognized:
Using the product for any purpose other than that for which the product is intended or
failing to follow the instructions for maintenance, operation and service of the product.
Damage to the product by a natural disaster, the intervention of an unauthorized
person or mechanically through the fault of the buyer (e.g. during transport, cleaning by
inappropriate means, etc.).
Natural wear and aging of consumables or components during use (such as batteries,
etc.).
Exposure to adverse external influences, such as sunlight and other radiation or
electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic
discharge voltage (including lightning), faulty supply or input voltage and inappropriate
polarity of this voltage, chemical processes such as used power supplies, etc.
If anyone has made modifications, modifications, alterations to the design or adaptation
to change or extend the functions of the product compared to the purchased design or
use of non-original components.

13
EU Declaration of Conformity
Identification data of the manufacturer's / importer's authorized representative:
Importer: Alza.cz a.s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
IČO: 27082440
Subject of the declaration:
Title: Smart Watch
Model / Type: ID205G
The above product has been tested in accordance with the standard(s) used to
demonstrate compliance with the essential requirements laid down in the
Directive(s):
Directive No. 2014/53/EU
Prague, 22.1.2021

14
WEEE
This product must not be disposed of as normal household waste in accordance with
the EU Directive on Waste Electrical and Electronic Equipment (WEEE - 2012/19 / EU).
Instead, it shall be returned to the place of purchase or handed over to a public
collection point for the recyclable waste. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of
this product. Contact your local authority or the nearest collection point for further
details. Improper disposal of this type of waste may result in fines in accordance with
national regulations.

15
Vážený zákazníku,
děkujeme Vám za zakoupení našeho produktu. Prosíme, pečlivě si přečtěte následující
instrukce před prvním použitím a uživatelský manuál si uschovejte pro pozdější užití.
Zejména dbejte na bezpečnostní pokyny. Pokud máte jakékoliv dotazy či připomínky
ohledně přístroje, prosíme, obraťte se na zákaznickou linku.
✉www.alza.cz/kontakt
✆[phone]
Dovozce Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

16
Jak spárovat hodinky s mobilním zařízením
1. Stažení a instalace aplikace
Hodinky můžete nastavit pomocí aplikace VeryFitPro pro zařízení iOS nebo Android.
Kroky jsou následující:
Poznámka: Vaše mobilní zařízení musí splňovat následující požadavky:
Verze iOS 8.0
nebo vyšší
Android systém 4.4
nebo vyšší
Podpora
Bluetooth 4.2
Správná operace:
Naskenujte níže uvedený
QR kód nebo si stáhněte
aplikaci VeryFitPro a
spárujte se s hodinkami. Nesprávná operace:
Spárujte hodinky přímo s
Bluetooth v nastavení
mobilního telefonu.
Správná operace:
Naskenujte níže uvedený
QR kód nebo si stáhněte
aplikaci VeryFitPro a
spárujte zařízení s
hodinkami.
Nesprávná operace:
Spárujte hodinky přímo s
Bluetooth v nastavení
mobilního telefonu.

17
2. Proces párování
Poznámky:
●Během procesu párování vás VeryFitPro vyzve k povolení GPS, Bluetooth a
přístupu k polohovým službám vašeho mobilního telefonu.
●iPhony vás nebudou vyzývat k žádným povolením, pokud nedokončíte párování
Bluetooth na hodinkách ID205G s Bluetooth v mobilním telefonu.
1. Zapněte Bluetooth a
GPS na svém mobilním
telefonu
2. Najděte žádost o
propojení v rozevíracím
seznamu na domovské
stránce aplikace
Vyberte model
produktu:
ID205G
Klikněte na „OK“ a
dokončete párování.