Amart Furniture 61350 User manual

61350
PARK CITY DESK BRW
61350
60CM
123CM
76CM
1-10

PRE-ASSEMBLY PREPARATION
BEFORE YOU START:
2
ALLOW 20 MINUTES PEOPLE REQUIRED
ADDITIONAL TOOLS REQUIRED
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product
2. Take care when lifting. Product should be assembled as near as possible to the point of use
3 . E n s u r e t h a t y o u h a v e a l l r e q u i r e d c o n t e n t s f o r c o m p l e t e a s s e m b l y
4 . A l w a y s r e a d t h e a s s e m b l y i n s t r u c t i o n s c a r e f u l l y b e f o r e b e g i n n i n g a s s e m b l y.
5 . K e e p a l l h a r d w a r e p a r t s a n d p a c k a g i n g o u t o f r e a c h o f s m a l l c h i l d r e n .
6. Do not over tighten the screws and bolts as this may damage the threads
61350
2-10

PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ST4X25mm
2pcs 2pcs 2pcs
Screw
Wall Nut Metal
61350
A
19pcs
B1
M6X25mm
6pcs
B2
M6X12mm
3pcs
C
ST3.5X12mm
24pcs
D1
ST5X50mm
18pcs
ST5X60mm
4pcs
D2
4pcs
E
E1
E2
F
8X30mm
6pcs
4pcs
G
Bolt Bolt Bolt
Screw
Screw Screw
Drawer slideway
Wood Dowel
H I J
Fixed Feet
12
12
13
14
15
15
13
1
5
243
6
11
10
9
8
10
11
8
9
7
Top panel
Left Side Panel
Right Side Panel
M Panel iddle
Left Front Drawer Panel
Right Front Drawer Panel
Back Panel
Drawer Left Panel
Drawer Right Panel
Drawer Back Panel
Bottom Drawer Panel
Metal Frame
Metal Tube
Metal Tube
Metal Tube
3-10

STEP 1
STEP 2
STEP 3
Assemble fixed feet (G) to metal frame (12).
61350
B2
B1
G
G
G
G
12
12
12
12
12
12
15
15
13
13
14
14
Assemble metal tube (13)&(14) to metal frame (12) using bolt (B1).
Assemble metal tube (15) to metal frame (12) and metal tube (14) using bolt (B1).
4-10

A
STEP 4
STEP 5
STEP 6
61350
2
FA
1
34
5
C
C
C
C
E1 E1
23
CC
E1 E2
E1 E2
C
C
E1 C
C
E1
44
CC
Assemble Drawer slideway ( E1) to middle panel (4) using screw (C).
Assemble Drawer slideway ( E1) to left side panel (2) and right side panel (3) using
screw (C).
Assemble top panel (1) to back panel (5),left side panel (2),right side panel (3)
and middle panel ( 4) using bolt (A) and wood dowel (F).
5-10

A
STEP 7
STEP 8
STEP 9
61350
A
7
D1
8
9
10
11
D2
D1
D1
D2
D1
D1
1
4
D1
D1
4
5
12
12
J
J
8
9
13
Assemble middle panel (4)to back panel (5) using screw (D1).
Connect metal fram (12) and top panel (1) and metal (J) using screw (D1) and screw
(D2).Connect middle panel (4) and metal tube (13) using screw (D1).
Assemble drawer back panel ( 10) to drawer left panel (8) and drawer right panel
(9) using screw (D1),then insert drawer bottom panel (11).Assemble left front
drawer panel (6) and right front drawer panel (7) to drawer left panel (8) and drawer
right panel (9) using bolt (A).
A
6
6-10

STEP 10
STEP 11
STEP 12
61350
6
7
C
C
E2
8
9
C
Assemble drawer slideway (E2) to drawer left panel (8) and drawer right panel using
screw (C).
Insert drawer (6) and (7).
Assembly is complete.
7-10

STEP 13
61350
Knock in wall nut (I) on the wall,then connect metal (J) and wall nut (I) using screw (H).
Fix the desk to the wall.
8-10
J
I
H

SAFETY BRACKETS INSTRUCTIONS
HARDWARE
Screw x 1
Wall Nut x 1
Metal x 1
Wall
Back Side
Attach one Mounting Plate to the wall with the Large Screws. Make sure to attach the
Mounting Plate into a stud. If mounting into brick or masonry you will need to acquire
wall anchors.
Attach the second Mounting Plate to the furniture frame with the Short Screws.
Move the furniture to its final position. Thread a Wall Strap through the both Mounting
Plates and tighten until snug. Do not over tighten.
Make sure that the Mounting Plates are firmly attached to the wall and furniture and
that the Wall Strap is snug.
1.
2.
3.
4.
9-10 61350

10-10 61350
CARE AND MAINTENANCE
A multi-step finish is applied to all of our furniture, but all wood comes from nature. Because
of this, there will be natural variations in surface texture and grain like knots, mineral streaks
and sap runs that may affect the finish. These differences in characterare not defects, but
distinctions that make each piece of furniture unique.
Following these steps for basic care should protect your investment for years to come..
Dust frequently with a clean damp lint-free cloth. This will help remove abrasive build up
which can damage a finish over time.
Do not place hot objects on any furniture surface. Always use a hot plate or placemat.
Laminate and lacquer finishes on tabletops provide added scratch and heat resistance to our
furniture, but they can still be damaged without proper care
Avoid exposing your furniture to strong sunlight, heat outlet, open windows or dampness.
Prolonged exposure to direct sunlight can fade the finish of your furniture, while extreme
temperature and humidity changes can cause cracking or splitting
Do not expose your furniture to any liquids. Never allow water to sit on your furniture. Alcohol,
nail polish and perfume are also dangerous as they will dissolve the lacquer finish on contact
and may require professional repairs
Do not allow plastic to come in direct contact with your furniture. Chemicals in the plastic of
placemats etc. may soften and mark the finish if left in contact with the furniture for a period
of time.