Amart Furniture NORMANDY 75819 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
NORMANDY KING BED
ITEM CODE 75819
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture , Customer Service Free call 1800 351
084
1ITEM CODE 75819

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2.Take care when lifting. Product should be assembled as near as possible to
the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2 ITEM CODE 75819
ALLOW 45 MINITES 2 PEOPLE REQUIRED
TOOLS REQUIRED
12
11
10
9
8
765
4
3
2
1
We recommend using a
screwdriver to put this item
together. However if you choose
to use a power drill it must be
used on LOW SPEED (LOW
TORQUE) as too much pressure
could damage the product

3ITEM CODE 75819
PARTS LIST
F. FLAT WASHER
2PCS 1PCS 24PCS
2PCS 10PCS
G. LOCK WASHER
8PCS
C. ALLEN KEY
B. BOLT 5/16''X60MM
A. BOLT 5/16''X32MM
8PCS
D. SCREW 4X30MM
E. SCREW 4X40MM
1 HEADBOARD
2 SIDERAILS
3SLATS (1836mm*88mm)
4 FOOTBOARD
5 CENTRE RAIL
6 SUPPORT LEGS

ITEM CODE 75819
•Attach side rail ( 2 ) to headboard (1) and footboard (4)
using flat washer (f), lock washer (g) and bolts (a).
•Tighten with Allen Key (c).
4
F. FLAT WASHER
1PCS 8PCS
G. LOCK WASHER
8PCS
ITEMS REQUIRED
1C. ALLEN KEY A. BOLT 5/16''X32MM
8PCS

ITEM CODE 75819
•Attach support legs (6) to centre rail (5) with flat
washer (f) and bolts (b)
•Tighten with allen key (c)
5
C. ALLEN KEY F. FLAT WASHER
1PCS 2PCS
ITEMS REQUIRED
2B. BOLT 5/16''X60MM
2PCS

6ITEM CODE 69583
•Attach centre rail (5) to head board (1) and foot board
(4) using screw (e).
•Use Screwdriver or Power Drill on Low Speed.
ITEMS REQUIRED
3E. SCREW 4X40MM
2PCS

•Attach slats (3) to siderail (2) using screws (d).
•Use Screwdriver or Power Drill on Low Speed.
7ITEM CODE 75819
ITEMS REQUIRED
4D. SCREW 4X30MM
24PCS

8ITEM CODE 75819
ASSEMBLY IS COMPLETE
CAUTION
Always Lift Your Bed When Moving /Relocating - Do Not Drag.
Dragging Can Cause The Centre Support Legs To Bend/Break.

9ITEM CODE 75819
Care and maintenance
•A multi-step finish is applied to all our furniture, but all wood comes
from nature. Because of this, there will be natural
variations in surface texture and grain like knots, mineral streaks and
sap runs that may affect the finish. These differences in character are
not defects, but distinctions that make each piece of furniture unique.
•Our furniture is built to last. Following these steps for basic care
should protect your investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help
remove abrasive build up which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a hot
plate or placemat. Laminate and lacquer finishes on table tops provide
added scratch and heat resistance to our furniture, but they can still
be damaged without proper care.
•Avoid exposing your furniture to strong sunlight, heat outlet, open
windows or dampness. Prolonged exposure to direct sunlightcan fade
the finish of your furniture, while extreme temperature and humidity
changes can cause cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit
on your furniture. Alcohol, nail polish and perfume are also dangerous
as they will dissolve the lacquer finish on contact and may require
professional repairs.
•Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc may soften and markthe
finish if left in contact with the furniture for a period of time.