Amart Furniture 64292 User manual

1 64292
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
LARSON LAMP TABLE
ITEM CODE 64292
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084

2 64292
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product
2. Take care when lifting. Product should be assembled as near as possible to the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads

3 64292
PARTS LIST
NO DESCRIPTION Qty
1 CHEST 1
4
2 LEGS 1
3 LEGS 1
a. Bolt M6x45
8pcs
b. Allen key M4
1pc
c. Bolt M4x25
8pcs
d. Handles
4pcs

4 64292
ITEMS REQUIRED
 With 2 people carefully turn item onto top on sheet or cardboard to protect surface.
 Attach legs ( 2 ) & ( 3 ) to Chest (1) using bolts (a).
 Tighten with Allen Key (b).
 with 2 people carefully turn upright.
ITEMS REQUIRED
 Please Remove two Drawers out chest as shown below.
a. Bolt M6x45
8pcs
b. Allen key M4
1pc

5 64292
ITEMS REQUIRED
 Attach Handles (d) to the Drawers using Screws (c).
c. Bolt M6x45
4pcs
C
C
d

6 64292
SAFETY BRACKETS INSTRUCTIONS
1. Attach one bracket to the wall, with the long screws as shown. Make
sure to attach the bracket into a stud. If mounting onto brick or
masonry, you will need to acquire wall anchors.
2. Attach a bracket to the furniture frame under the top with the short
screws provided.
3. Move the furniture into its final position. Thread a strap through the
bracket as shown in the illustration, tighten strap until snug. Do not
over tighten.
4. Make sure the bracket is firmly attached to the wallboard and
furniture, and the strap is snug.

7 64292
ASSEMBLY IS COMPLETE

Care label for timber items
 A multi-step finish is applied to all our furniture, but all wood comes from
nature. Because of this, there will be natural variations in surface texture
and grain like knots, mineral streaks and sap runs that may affect the finish.
These differences in character are not defects, but distinctions that make
each piece of furniture unique.
 Our furniture is built to last. Following these steps for basic care should
protect your investment for years to come.
 Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
 Do not place hot objects on any furniture surface. Always use a hot plate or
placemat. Laminate and lacquer finishes on table tops provide added
scratch and heat resistance to our furniture, but they can still be damaged
without proper care.
 Avoid exposing your furniture to strong sunlight, heat outlet, open windows
or dampness. Prolonged exposure to direct sunlight can fade the finish of
your furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
 Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
 Do not allow plastic to come in direct contact with your furniture. Chemicals
in the plastic of placemats etc may soften and mark the finish if left in
contact with the furniture for a period of time.