Amart Furniture CABOS BUFFET 3 DOOR 72789 User manual

1
ASSEMBLY INSTRUCTION
CABOS BUFFET 3 DOOR
ITEM CODE: 72789
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
for any assistance to assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
for any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084
72789
1500mm
450mm
950mm

BEFORE YOU START :
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product
2. Take care when lifting. Product should be assembled as near as possible to the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
PRE-ASSEMBLY PREPARATION
ALLOW 20 MINUTES 2 PEOPLE REQUIRED
ADDITIONAL TOOLS REQUIRED
We recommend using screw
driver to put this item together.
However if you choose to use a
power drill it must be used on
LOW SPEED (LOW TORQUE)
as too much pressure could
damage the product.
272789

B. Wall Strap
Ø4 x 15mm 2 pcs
A. Mounting Plate
4 pcs
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to attach the
Mounting Plate into a stud. If mounting into brick or masonry you will need to acquire wall
anchors.
2. Attach the second Mounting Plate to the funiture frame with the Short Screws.
3. Move the funiture to its final position. Thread a Wall Strap through the both Mounting
Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and furniture and that
the Wall Strap is snug.
WALL BACK SIDE
SAFETY BRACKETS INTRUCTIONS
HARDWARE
This furniture poses a tipping risk and as such must be secured to a wall using the provided
tipping kit.
C. Large Screw
Ø5 x 40mm 4 pcs Ø4 x 20mm 4 pcs
D. Small Screw
D
B
C
A
A
372789

1
Product Care for Timber Items
As our timber is supplied from sustainable forests there will be
natural variations in surface texture and grain like knots, mineral
streaks and sap runs that may affect the finish.These differences in
character are not defects, butdistinctions that make each piece of
furniture unique
Our furniture is builtto last. Following these steps for basic care
should protect your investmentfor yearsto come
•Dust frequentlywith a clean damp lint-free cloth. This will help
remove abrasivebuildup which can damage a finish overtime
•Do not place hot objects on any furnituresurface.Always use a
hot plateor placemat. Laminate and lacquerfinisheson table
tops provide added scratch and heat resistance to our
furniture,but they can still be damaged without proper care
•Avoid exposing your furniture to strong sunlight, heat outlet,
open windows or dampness. Prolonged exposure to direct
sunlightcan fade the finish of your furniture,whileextreme
temperature and humidity changes can cause cracking or
splitting
•Do not expose your furnitureto any liquids. Never allow water
to sit on your furniture.Alcohol, nail polish and perfume are
also dangerous as they will dissolvethe lacquerfinish on
contact and may requireprofessional repairs
•Do not allow plastic to come in direct contact with your
furniture.Chemicals in the plastic of placemats etc. may soften
and mark the finish ifleft in contact with the furniture for a
period of time
472789