Amart Furniture HOPI 58356 User manual

ASSEMBLY INSTRUCTION
ITEM CODE -
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia. For any
assistance with assembly or for missing parts please phone Amart Furniture,
Customer Service Freecall 1800 351 084.
1 / 11 58356
58356
HOPI SINGLE TEE PEE BED
Furniture

PRE-ASSEMBLY PREPARATION
2 / 11 58356
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
ADDITIONAL TOOLS REQUIRED

3 / 11 58356
JCBC Bolt M8x15mm
Ax 12 pcs
JCBC Bolt M8x30mm
Bx 12 pcs
Allen Key - M6
Cx 4 pcs
PARTS LIST
NO. PART QTY. PICTURE PACKING CARTON
1SIDE FRAME PANEL 2 PCS 1/3
2 RAFTER - LEFT & RIGHT 4 PCS 2/3
3 RAFTER SUPPORT 2 PCS 2/3
4 TOP FRAME BOTTOM SUPPORT 2 PCS 2/3
5 METAL RIDGE 1 PC 3/3
6 END FRAME PANEL 2 PCS 3/3
7 BED POST 4 PCS 2/3
8 SIDE RAIL 2 PCS 3/3
9 FABRIC SUPPORT RAIL 2 PCS 3/3
10 FABRIC WITH HOLE 2 PCS 1/3
11 FABRIC WITHOUT HOLE 1 PC 1/3
12 WOOD SLAT (9pcs/set)
- 18mm x 59mm x 920mm 2 SETS 3/3
CSK Chipboard Screw
#4 x 50mm
JCBC Bolt M6x15mm JCBC Bolt M6x30mm
JCBC Bolt M6x45mm CSK Chipboard Screw
#4 x 30mm
Allen Key - M8
Dx 18 pcs
Ex 8 pcs Fx 10 pcs Gx 4 pcs Hx 1 pc
Ix 1 pc

4 / 11 58356
11
10
10
5
9
2
2
3
1
7
6
8
9
6
7
7
2
2
3
1
4
4
12

5 / 11 58356
STEP 1 :
STEP 2 :
JCBC Bolt M8x30mm
Bx 12 pcs
Fix end frame panel 6 to the bed post with bolts B as shown.
Fix bolts A (upper & lower bolts) into position
on bottom frame panel as shown. After that,
hook the side rail to the bolt and fix center bolts
A as show.
7
7
6
B
B
8
8
A
JCBC Bolt M8x15mm
Ax 12 pcs
A

6 / 11 58356
12
F
STEP 3 :
STEP 4 :
Put wood slats to the side rail support and fix screws F at hole as shown.
Fix all top frame component with hardware as shown.
2
2
3
1
D
4
JCBC Bolt M6x30mm
Dx 4 pcs
CSK Chipboard Screw
#4 x 30mm
Fx 8 pcs
CSK Chipboard Screw
#4 x 50mm
Gx 4 pcs
CSK Chipboard Screw
#4 x 30mm
Fx 2 pcs
F
G

7 / 11 58356
D
E
STEP 5 :
Assemble top side frame to the end frame with bolts D and E as shown.
Note : Do not tighten the bolts yet.
STEP 6 :
Fix metal ridge to the both top side frame with bolts C as
shown and tighten all bolts.
JCBC Bolt M6x30mm
Dx 4 pcs
JCBC Bolt M6x45mm
Ex 8 pcs
JCBC Bolt M6x15mm
Cx 4 pcs

8 / 11 58356
9
Fix Fabric with hole and Fabric support rail as shown.
STEP 7 :
Fix bolts D to the Fabric support rail and Side rail as shown.
At last fix Fabric without hole on top of Metal ridge as shown.
STEP 8 :
JCBC Bolt M6x30mm
Dx 5 pcs
D

9 / 11 58356
ASSEMBLY IS COMPLETE

10 / 11 58356
Product Care for Hi-Gloss Items
Hi-gloss lacquered furniture is more sensitive to marks and scratching then some other furniture
products. It is important to exercise caution and care to maximise the life and beauty of
this product.
Following the below simple guidelines when using your hi-gloss product will protect your
investment for years to come.
.Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
.Do not place hot objects on any furniture surface. Always use a hot plate or
placement. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
.Avoid exposing your furniture to strong sunlight, heat outlet, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
.Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
.Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placements etc may soften and mark the finish if left in contact
with the furniture for a period of time.
.Avoid placing sharp or rough objects on the surface of your furniture. These
may scratch the surface of the product.
.When moving your furniture, do not drag it across the floor. This may damage
the product. Instead use two (2) people to lift carefully from either end.