Amart Furniture RAYNA 75825 User manual

175825
ASSEMBLY INSTRUCTION
RAYNA KING SINGLE BED
ITEM CODE 75825
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture, Customer Service Free Call
Imported by Amart Furnityre Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart furniture, Customer Service Free call 1800 351 084
1800 351 084
2240MM
1210MM
1040MM

Before you start:
275825
PRE-ASSEMBLY PREPARATION
1. Choose a clean, level, spacious assembly area. Avoid hard
surfaces that may damage the product
2. Take care when lifting. Product should be assembled as near
as possible to the point of use
3. Ensure that you have all required contents for complete
assembly
4. Always read the assembly instructions carefully before
beginning assembly
5. Keep all hardware parts and packaging out of small children
6. Do not over tighten the screws and bolts as this may damage
the threads

PARTS LIST
375825
ABM5X100mm x1pcs CM12mm x1pcs DM8x12mm x6pcs EM4X30mm x8pcs FM8X40mm x6pcs
GHI
M4X65mm x1pcs
M8X19mm x10pcs
M6X20mm x8pcs
Allen key
Screw
Nut
Bolt
Wrench
Allen key Bolt
Flat washer
11
JM8X25mm x4pcs
Bolt
12345
78910 11
6
1PCS
Headboard
Center slat rail Slat
Rail
Support leg Leg
1PCS 1PCS 1PCS 1PCS 1PCS
2PCS 1PCS 2PCS 2PCS 1PCS 4PCS
Rail Rail Rail Footboard
Support leg Support leg
M6X19mm x8pcs
Flat washer
1
2
3
6
5
10
4
12
12
9
8
9
10
12
12
7
7
12

STEP 1
475825
STEP 2
Lay the Headboard(1) down, bottom facing
up.Fasten the Feet(12) to the Headboard(1).
Lay the Footboard(6) down, bottom facing
up.Fasten the Feet(12) to the Footboard(6).

5
STEP
75825
4
5
2
3
10
4
10
9
7
8
B
F
A
C
D
7
9
B
F
A
C
D
G
H
I
10
3
2
STEP 3 Connect the side rails together by attaching the
support leg (10) with bolts (G) and washers (I) and tighten with Allen
key (H).
Attach support legs (8/9) to centre rail (7) using Bolt
(F) washer (A) and nut (D) as shown. Hold nut (D) in
place with wrench (C) and tighten bolt (F) with allen
key (B).

STEP 5
6
STEP
75825
6
B
B
3
2
1
4
56
B
J
A
6
7
7
1
Loosen bolts in Headboard / Footboard (1/6), place
brackets of side rails (2/3) and (4/5) over the bolts
and tighten bolts using Allen key (B).
Attach centre rail (7) to Headboard and Footboard (1/6)
with bolt (J) and washer (A) and tighten with allen key
(B).

ASSEMBLY IS COMPLETE
STEP 7
7 75825
E
E
11
Attach slats (11) to side rails (2/3) (4/5) using screws (E).
CAUTION:
ALWAYS LIFT YOUR BED WHEN MOVING/
RELOCATING - DO NOT DRAG.
DRAGGING CAN CAUSE THE SUPPORT LEGS TO
BEND/BREAK.

8
Fabric Care and
75825
Maintenance
REGULAR CARE:
• Protect from direct sunlight
• Vacuum regularly using low suction
• Rotate reversible cushions regularly
CLEANING:
• Do not remove cushion covers for separate cleaning even though
they may have zippers
• Do not wash, Do not dry clean, Do not shampoo clean
• Clean with hot water extraction machine. Professional cleaning
recommended
• Do not use dishwashing liquid or laundry detergent
• Use only upholstery detergents
• Do not wet filling
• Dry in shade away from direct heat and sunlight
• Allow to dry thoroughly before re-use
SPOT CLEANING:
• Do not rub
• Do not spot clean with any solvent
• Treat spills and stains as soon as possible
• Gently scrape off any soil or mop any liquid from the surface of the
fabric
• Apply proprietary cleaning agents strictly according to instructions to
remove the residue of the spill
• Do not saturate the fabric or interior with water or other cleaning liquids
WARNING:
Apply only water-based soil resist (fabric protection) treatments. Do not
use aerosol products
* PILLING IS NOT A FABRIC DEFECT OR FAULT AND IS NOT
COVERED BY WARRANTY
* PILLING IS A NORMAL OCCURRENCE CAUSED BY WEAR AND
TEAR AND DOES NOT AFFECT THE DURABILITY OR
FUNCTIONALITY OF THE FABRIC AND IS EASILY REMOVED