Amart Furniture LA SALLE MK2 65966 User manual

ASSEMBLY INSTRUCTION
LA SALLE MK2 LAMP TABLE
ITEM CODE 65966
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
65966

1
IMPORTANT: CARE GUIDE FOR YOUR
TIMBER FURNITURE
•Congratulations! You have just purchased a quality product from Amart
Furniture. Please read on for important information regarding your purchase.
•A multi-step finish is applied to all our furniture, but all wood comes from
nature. Because of this, there will be natural variations in surface texture and
grain like knots, mineral streaks and sap runs that may affect the finish.
•These differences in character are not defects, but distinctions that make
each piece of furniture unique.
•Our furniture is built to last. Following these steps for basic care should
protect your investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a coaster or
placemat. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
•Avoid exposing your furniture to strong sunlight, heat outlets, open windows
or dampness. Prolonged exposure to direct sunlight can fade the finish of
your furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
•Do not allow plastic to come in direct contact with your furniture. Chemicals
in the plastic of placemats etc may soften and mark the finish if left in contact
with the furniture for a period of time.
65966

2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
65966

A M6 X 30 BOLT 12
PCES B M6 X 80 BOLT 4 PCES C M6.5 X 19 FLAT WASHER 16 PCES D M6.5 X 9 SPRING
WASHER
16
PCES
E ALLEN KEY 24
PCES
Part DESCRIPTION Qty Part DESCRIPTION Qty
1 TABLE TOP 1 4 LEG UPPER 1
2 PLATE 1 5 LEG LOWER 1
3 PEDESTAL 1
PARTS LIST
3
1
2
5
65966

Step 1
You should have started by opening the box upside down. Keep the
table top inside the box until later advised.
Step 2
Next you will need to assemble the M6 x 30 bolts (item A) with the
M6.5 x 9 spring washers (item D) and the M6.5 x 19 flat washers
(item C)
A M6 X 30 BOLT 12
PCES C M6.5 X 19 FLAT WASHER 12 PCES D M6.5 X 9 SPRING
WASHER
12
PCES G ALLEN KEY 1 PCE
YOU WILL NEED
465966

Step 3
Take 4 of the assembled bolt sets from step 2 and affix the plate (part
2) to the pedestal (part 3) with the Allen key provided (item E).
Fasten firmly, but do not over tighten, over tightening may damage
surface of item.
Step 4
Next you will need to assemble the M6 x 80 bolts (item B) with the
M6.5 x 9 spring washers (item F) and the M6.5 x 19 flat washers
(item E)
YOU WILL NEED
5
B M6 X 80 BOLT 4
PCES C M6.5 X 19 FLAT WASHER 4 PCES D M6.5 X 9 SPRING
WASHER
4
PCES G ALLEN KEY 1 PCE
65966

Step 5
Start by turning the pedestal upside down, resting on the plate. Criss-
cross the upper and lower legs as per the diagram below. Then fix the
legs to the pedestal with the 4 assembled bolts set from step 4, using
the Allen key provided (item E). Fasten firmly, but do not over
tighten, over tightening may damage surface of item.
665966

Step 6
Take the remaining 8 assembled bolt sets from step 2 and use them
to fasten the plate and pedestal structure to the table top. Use the
Allen key provided (item E). Fasten firmly, but do not over tighten,
over tightening may damage surface of item.
Step 7
Finally flip the lamp table over. This is a 2 person task do not do this
alone. Once the right way up, remove the packaging from the table
top.
765966

Attaching the anti-tipping kit.
As wall types vary, we do not supply the screws that you will need, to fasten
onto your wall. Please seek advice from you trusted local specialist.
Step 1
Attach one of the anchors to the underside of lamp table top.
Step 2
Mark the spot on the wall that will best line up with the anchors already fixed
on the unit. For best results we recommend placing the wall anchor to one side
and not directly inline with the unit anchor.
Step 3
After sourcing the correct screw system for your wall type, fasten the wall side
of the anchor.
Step 4
Move the unit into position and lock the uni anchor to the wall anchor together
with the cable tie supplied. Do for each anchor point on the unit.
865966

9
Assembly is complete
65966