Amart Furniture Winton 72062 User manual

2280mm
1500mm
2140mm
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts, please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
WINTON QUEEN BED
ITEM CODE 72062
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts, please phone
Amart Furniture, Customer Service Free call 1800 351 084
ITEM CODE 72062
1

ITEM CODE 72062
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Take care when lifting. Product should be assembled as near as possible to the
point of use.
3. Ensure that you have all the required contents for complete assembly.
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads.
PRE-ASSEMBLY PREPARATION
Power drill set to low speed setting before use.
2
12 1
2
3
4
5
6
7
8
9
10
11
X2
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
ADDITIONAL TOOLS REQUIRED

ITEM CODE 72062
PART LIST
2
1pc
HEADBOARD1 1pc
FOOTBOARD WITH DRAWER
3
1pcSIDERAIL (LEFT)
DESCRIPTIONNO. QTY.
Note: Hardware are located inside siderail boxes.
A. Spring Washer
M8 30pcs
5
1pc
SLAT
4
12pcs
SLAT SUPPORT
6
1pcSLAT SUPPORT LEG
U BLOCK
7
2pcs
3
B. Flat Washer
M8 30pcs
C. Bolt
JCBC M8 x 16 8pcs
D. Bolt
JCBC M8 x 40 24pcs
E. Bolt
JCBC M6 x 40 8pcs
F. Screw
CSK M4 x 32mm 32pcs
G. Dowel
M8 x 40 4pcs
H. Dowel
M8 x 50 3pcs
7
1
5
6
8
2
9
10
HEADBOARD BASE 1pc
8
9
1pcSIDERAIL (RIGHT)
10
HEADBOARD SUPPORT 3pcs
4
10
3
3
3
I. Allen Key
M4 1pc
J. Allen Key
M5 1pc
K. Screw
CSK M4 x 50mm 2pcs

ITEM CODE 72062
4
C. Bolt
JCBC M8 x 16
8pcs
ITEMS REQUIRED
1
- Attach Siderail (5 & 6) to Headboard Base (2) & Footboard (4)
by pushing the bracket down.
- Attach U Block (10) to Headboard Base (2) & Drawer Footboard (4)
using Dowel (G) & Screws (F).
- Tighten with screw driver or power drill on low setting.
G. Dowel
M8 x 40
4pcs
F. Screw
CSK M4 x 32mm
8pcs
I. Allen Key
M4
1pc
8
2
6
5
4
Note:
Use plastic hammer
driving wood Dowel (G)
into U-Block (10) and
fit to Headboard Base (2)
and Footboard (4) before
screw in as below.
E. Bolt
JCBC M6 x 40
2pcs
J. Allen Key
M5
1pc
- Slot in Slat Support (8) to both U Block (10).
- Attach Slat Support Leg (9) to Slat Support (8)
using Bolts (E) and Allen Key (I).
- Secure all 4 corners using Bolts (C) to Headboard Base (2)
& Footboard (4) using Allen Key (J).
9
8
10
10

ITEM CODE 72062
5
ITEMS REQUIRED
2
- Install all three Headboard Support (3) to the back of Headboard Base (2) using Bolts (D),
Spring Washer (A), Flat Washer (B) and Allen Key (J).
- Please refer to diagram for which bolts, washers and Allen keys to use in each position.
- Insert Dowel (H) to Headboard Base (2) as guide and support for Headboard (1).
- Secure Footboard (4) to both Siderail (5 & 6) using Screw (K).
D. Bolt
JCBC M8 x 40
24pcs
B. Flat Washer
M8
30pcs
A. Spring Washer
M8
30pcs
- Mount Headboard (1) to Headboard Support (3).
- Use wooden Dowel (H) to guide the positioning of Headboard (1).
- Please refer to diagram for the type of Bolts to use in different position.
E. Bolt
JCBC M6 x 40
6pcs
I. Allen Key
M4
1pc
J. Allen Key
M5
1pc
3
2
4
6
5
3
3
1
3
3
K
K
K
3
H. Dowel
M8 x 50
3pcs
K. Screw
CSK M4 x 50mm
2pcs

ITEM CODE 72062
6
ITEMS REQUIRED
3
Important Notes:
- Once the bed is positioned, the support leg should be adjusted to touch the floor.
- The slat may then be laid down and secured before putting on the mattress.
- DO NOT push or pull the bed for repositioning as this may damage the bed
and cause the support leg for the centre rail to break.
F. Screw
CSK M4 x 32mm
24pcs
- Once the bed is positioned, the Slat Support Leg (9) should be adjusted to touch the floor.
- Place Slats (7) to ledge of Side Rails (5 & 6).
- Attach together using Screw (F).
- Tighten with screw driver or power drill on low speed setting. 9

ITEM CODE 72062
7
CARE AND MAINTENANCE
A multi-step finish is applied to all our furniture, but all wood comes
from nature. Because of this, there will be natural
variations in surface texture and grain like knots, mineral streaks and
sap runs that may affect the finish. These differences in character are
not defects, but distinctions that make each piece of furniture unique.
Our furniture is built to last. Following these steps for basic care
should protect your investment for years to come.
Dust frequently with a clean damp lint-free cloth. This will help
remove abrasive build up which can damage a finish over time.
Do not place hot objects on any furniture surface. Always use a hot
plate or placemat. Laminate and lacquer finishes on table tops
provide added scratch and heat resistance to our furniture, but they
can still be damaged without proper care.
Avoid exposing your furniture to strong sunlight, heat outlet, open
windows and dampness. Prolonged exposure to direct sunlight can
fade the finish of your furniture, while extreme temperature and
humidity changes can cause cracking or splitting.
Do not expose your furniture to any liquids. Never allow water to sit
on your furniture. Alcohol, nail polish and perfume are also dangerous
as they will dissolve the lacquer finish in contact and may require
professional repairs.
Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc may soften and mark the
finish if left in contact with the furniture for a period of time.