AmazonBasics B071JLRR3T User manual

created by: Impala Services Ltd.Page size: 139.7 x 107.95 mm
B071JLRR3T
Aluminum Medium Duty Press Board Double Post Shelf
Estante De Poste Doble De Aluminio De Resistencia Media De Madera Comprimida
Étagères Moyennes En Aluminium Dotées De Montants Doubles Et De Panneaux Comprimés
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 1 8/28/17 2:54 PM

English ..................................... 3
Español.................................. 14
Français ................................. 25
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 2 8/28/17 2:54 PM

3
Welcome Guide •English
Aluminum Medium Duty Press
Board Double Post Shelf
Contents:
Before getting started, ensure the package contains the following components:
Part Qty
Beam 10
Brace 10
Bottom post 4
Top post 4
Press board 5
Bottom protective cover 4
Top protective cover 4
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 3 8/28/17 2:54 PM

4
Assembly
Step 1:
Setting Up the Product
• Insert all 4 bottom protective covers to bottom posts , insert all 4 top protective covers
to top posts .
• Note: Do not omit this step, which could protect your floor from scratches.
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 4 8/28/17 2:54 PM

5
Assembly
Step 2:
Setting Up the Product
• Slide the rivets of brace into bottom posts of your desired location with the key slot
pointing down and shelf ledge of brace facing up. Tap lightly to seat rivets.
• Note: Make sure all the rivets are fully seated into the post slots. You may want to use a rubber
mallet (not included) to help push the rivets into the post slots. This applies to all the rivets used
in this unit.
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 5 8/28/17 2:54 PM

6
Assembly
Step 3:
Setting Up the Product
• Repeat the previous step 2 to attach beams and braces to bottom posts until the first
level is assembled.
• Note: Each of the beams and braces on the same level should be at the same height.
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 6 8/28/17 2:54 PM

7
Assembly
Step 4:
Setting Up the Product
• Repeat the previous two steps to attach beams and braces to posts until the first two
levels are assembled.
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 7 8/28/17 2:54 PM

8
Assembly
Step 5:
Setting Up the Product
• Top posts , bottom posts , beams , braces should be connected as illustrated.
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 8 8/28/17 2:54 PM

9
Assembly
Step 6:
Setting Up the Product
• Repeat step 2 & 3 to form the fourth to fifth levels.
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 9 8/28/17 2:54 PM

10
Assembly
Step 7:
Setting Up the Product
• Hold the press board at an angle to make it easier to fit them onto each previously
assembled level on the frame.
B071JLRR3T-AmazonBasics-IM-V01 (US).indb 10 8/28/17 2:54 PM