AmazonBasics B01D7P5BFS User manual

created by: Impala Services Ltd.Page size: 4.25“ x 3.5“ (~108 x 89 mm)
Low-Back Computer Chair
Chaise d’Ordinateur à Dossier Bas
Computerstuhl mit niedriger Rückenlehne
ローバックコンピューターチェア
B01D7P5BFS
B01D7P5JW8
B01D7P5NI8
B01D7P5QKS

English Français Español 日本語
English ........................................... 3
Français ....................................... 14
........................................ 25
......................................... 36
Español
日本語

3
English Français Español 日本語
Welcome Guide •English
Low-Back Computer Chair
Contents:
Before getting started, ensure the package contains the following
components:
Part Qty
Back Cushion 1
Seat Cushion 1
Seat Plate 1
Gas Lift 1
Base 1
Casters 5
Bolts (A) 4
Hex key (B) 1
Knob and Washers (C) 1

4
English Français Español 日本語
Assembly
Step 1
Setting Up the Product
•Turn the base upside down and press the casters into the holes of each of the
base legs. Check that they are securely fixed.

5
English Français Español 日本語
Assembly
Step 2
Setting Up the Product
•Place the base upright and insert the gas lift with cover into the hole of the base.
The lift cover should be placed over the lift.

6
English Français Español 日本語
Assembly
Step 3
Setting Up the Product
•Align the seat plate over the pre-drilled holes underneath the seat cushion.
Make sure that the seat plate is properly aligned to the cushion (as shown
above).
•Attach the seat plate to the seat cushion using four bolts. Tighten all bolts with
the hex key. CAUTION: Do not overtighten the bolts! It may damage the bolts
or the seat.
FRONT
A
B

7
English Français Español 日本語
Assembly
Step 4
Setting Up the Product
•Insert the back bar of the back cushion into the seat plate.
•Align the hole on the back bar to the hole on the seat plate.
•Fix the bar to the pre-drilled holes and then secure it using knob and washers.
FRONT
C

8
English Français Español 日本語
Assembly
Step 5
Setting Up the Product
•Turn the seat cushion upright and insert the gas lift in the hole of the seat plate.
•Push the seat cushion down onto the gas lift firmly until the connection is secure.
•Caution: Before using your chair, make sure that all bolts are fully tightened.
•Tip: Store the hex key for later use and check the bolts periodically to make
sure they remain securely tightened.

9
English Français Español 日本語
Assembly
Step 6
Adjusting the Seat Height
•To raise the seat, lean forward and lift your body weight from the seat. And pull
up the control handle.
•To lower the seat, pull up the control handle while you are seated.

10
English Français Español 日本語
Cleaning and Maintenance
•Periodically clean the seat cover using a vacuum cleaner. Use the correct
attachment for vacuuming upholstery. Use the setting for upholstery (low
suction).
•Use a dry sponge to remove dirt.
•If required, use a slightly damp cloth to clean heavily soiled areas, then wipe
dry using a dry cloth.
•Occasionally, thoroughly wipe the frame using a slightly damp cloth. Then dry
the frame using a dry cloth.
•Do not use strong cleaning agents or abrasives.
•Do not use the chair unless all screws are securely fastened. Screws and
joints should be re-tightened regularly.
Weight 7.00 kg (15.43 lbs)
Maximum load weight 124.70 kg (275 lbs)