AMD DIrect SSRFR-24DK User manual

KEGERATOR
USER MANUAL

AMD DIRECT KEGERATOR
INSTALLATION INSTRUCTIONS & OWNERS MANUAL
24” 6.6C DELUXE OUTDOOR RATED NO TAP KEGERATOR
24” 6.6C DELUXE OUTDOOR RATED SINGLE TAP KEGERATOR
24” 6.6C DELUXE OUTDOOR RATED DUAL TAP KEGERATOR
NAME:
SSRFR24DK
SSRFR24DK1
SSRFR24DK2
PART #:
THANK YOU
Thank you for your purchase. We’d like to welcome you to the AMD Direct family of luxury
outdoor kitchen products and look forward to being a part of your home for years to
come. As a family business with over 20 years of industry experience, we aim to deliver
exceptional quality and personal service. Welcome to the AMD Direct family and we hope
you love your new kegerator!
INSTALLER
Please leave this manual for the owner
Serial Number:
Model:
Date of Purchase:
Place of Purchase:
To view on your phone, scan the QR code on your camera app.
camera app. (For Android devices, use Google Lens)
For warranty information and to register your kegerator visit,
AMDDirect.com/register

KEGERATOR USER MANUAL
SAFETY AND INSTALLATION INSTRUCTIONS GENERAL SAFETY REQUIREMENTS
• The appliance should be located in the
coolest area of the room or outdoor
location, away from heat-producing
appliances and out of direct sunlight.
• Do not overload the beer dispenser as it
forces the compressor to run longer.
• Position items so that air can circulate
freely around them.
• Do not leave door open for longer than
required.
• Make sure items do not touch the back of
the storage compartment.
• Do not set the thermostat to exceedingly
cold temperatures.
ENERGY SAVING TIPS
FOLLOW WARNING CALLOUTS BELOW
ONLY WHEN APPLICABLE TO YOUR
MODEL
• Use two or more people to move and install
appliance. Failure to do so can result in back
or other injury.
• To ensure proper ventilation for your
appliance, the front of the unit must be
completely unobstructed.
• Choose a well-ventilated area with
temperatures above 50°F (10°C) and below
109.4°F (43°C).
• The appliance should not be located next to
ovens, grills, or other sources of high heat.
• The appliance must be installed with all
electrical, water, and drain connections in
accordance with state and local codes. A
standard electrical supply (115 V AC only,
60HZ), properly grounded in accordance with
the National Electrical Code and local codes
and ordinances is required.
• Do not kink or pinch the power supply cord of
the appliance.
• The size of the fuse (or circuit breaker) should
be 1.3 amperes.
• It is important that the appliance be leveled in
order to work properly. You may need to make
several adjustments to level it.
• All installations must be in accordance with
local plumbing code requirements.
• Never allow children to operate, play with or
crawl inside the appliance.
• Do not use solvent-based cleaning agents or
abrasives on the interior. These cleaners may
damage or discolor the interior.
• Use this appliance only for its intended
purposes as described in this instruction
manual.
• Keep fingers out of the “pinch point” areas.
Clearances between the drawer and cabinet
are necessarily small. Be careful closing
drawer when children are in the area.
1. Child entrapment and suocation are not
problems of the past. Junked or abandoned
appliances are still dangerous, even if they
will “just sit for a few days.”
2. Before discarding your old refrigerator: Take
o kegerator parts. Removing any hoses or
fittings.
RISK OF CHILD ENTRAPMENT
1. Stainless steel exposed to chlorine gas
and moisture – such as areas with spas
or swimming pools – may experience
discoloration. This discoloration from chlorine
gas is normal.
2. NEVER USE CHLORIDE TO CLEAN
STAINLESS STEEL.
• Plug into a grounded 3-prong outlet, do not
remove prong, do not use an adapter and do
not use an extension cord.
• Replace all panels before operating.
• It is recommended that a separate circuit
serving only your appliance be provided. Use
receptacles that cannot be turned o by a
switch or pull chain.
• Never clean appliance parts with flammable
fluids. These fumes can create a fire hazard or
explosion.
• Do not store or use gasolines or other
flammable vapors and liquids in the vicinity
of this or any other appliance. The fumes can
create a fire hazard or explosion.
• Do not connect or disconnect the electric plug
when your hands are wet.
• Unplug the appliance or disconnect power
before cleaning or servicing. Failure to do so
can result in electrical shock or death.
• Do not attempt to repair or replace any part
or your appliance unless it is specifically
recommended in this manual. All other
servicing should be referred to a qualified
technician.
Most power failures are corrected within a few
hours and should not aect temperature of your
appliance if you minimize the number of times the
drawer is opened. If the power is going to be o
for a longer period of time, take proper steps to
protect the contents.
Short Vacations: Leave the appliance operating
during vacations of less than three weeks.
Long Vacations: If the appliance will not be used for
several months, remove all items and turn o the
appliance. Clean and dry the interior thoroughly. To
prevent odor and mold growth, leave the door open
slightly, blocking it open if necessary.
• Remove all items.
• Securely tape down all loose items
inside your appliance.
• Turn the adjustable legs up to the base
to avoid damage.
• Tape the door shut.
• Be sure the appliance stays secure in the
upright position during transportation.
Also protect the outside of the appliance
with a blanket or similar item.
Before the appliance is used, it must be properly
positioned and installed as described in this
manual, so read the manual carefully. To reduce
the risk of fire, electrical shock or injury when
using the appliance, follow basic precautions,
including the following:
WARNING WARNING
CAUTION
POWER FAILURE
VACATION TIME
MOVING YOUR APPLIANCE
WARNING

KEGERATOR USER MANUAL 7
KEGERATOR
USER MANUAL
TABLE OF CONTENTS
BEFORE OPERATING
TROUBLESHOOTING
OPERATING YOUR APPLIANCE
INSTALLATION
WARRANTY
1
2
3
4
6

1KEGERATOR USER MANUAL 2
TROUBLESHOOTING
You can solve many common problems easily, saving
you the cost of a possible service call.
Reference the troubleshooting table below before
calling the servicer.
PROBLEM SOLUTION
Kegerator does not operate Not plugged in or the appliance is turned o.
The circuit breaker tripped or a fuse has blown out.
Kegerator is not cold
enough
Check the temperature control setting.
External environment may require a higher setting.
The door is opened too often.
The door is not closed completely.
The door gasket is not sealing properly.
Kegerator is turning on and
o frequently
The room temperature is hotter than normal.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work Not plugged in.
The circuit breaker tripped or a fuse that the kegerator
is plugged into has blown.
The light bulb has burned out.
The light button is “OFF”
PROBLEM SOLUTION
Vibrations Check to assure that the kegerator is on a level
surface.
The kegerator seems to
make too much noise
A faint humming noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds
caused by the flow of the refrigerant in your kegerator.
Contraction and expansion of the inside walls may
cause popping and crackling noises.
During the defrosting process you may hear a water
flowing sound caused by water flowing through the
drain trough.
The kegerator is not on a level surface.
The door will not close
properly
The kegerator is not on a level surface.
The gasket is dirty.
The shelves are out of position.
Smell/Odor Check for leaks on inside surface or around the
keg coupler.
Outer surface of appliance
is wet
Condensation has formed and can be wiped dry.
External surface is warm Compressor is working to transfer heat from inside
the cabinet.
BEFORE OPERATING
Shipment Arriving Damaged:
INTERIOR LIGHT
TEMPERATURE ALARM
CLEANING AND MAINTENANCE
Important Notes:
VISIBLE DAMAGE
If your shipment arrives with visible damage to the
box/carton, be sure the damage is noted on the
bill of freight or express receipt and signed by the
person making the delivery. File a claim for damages
immediately, regardless of the extent of damage.
CONCEALED DAMAGE
If damages are unnoticed until the kegerator is
unpacked, notify the transportation company or
carrier immediately and file a concealed damage
claim with them. This should be done within (5)
days of the delivery date. Be sure to hold on to
the box/carton for inspection. We cannot assume
responsibility for damage or loss incurred in transit.
CONSTRUCTION ZONES
Keep all stainless steel products away from
construction zones. Construction debris such as
(but not limited to) stone dust, stucco, and lime dust
could damage or permanently discolor stainless
steel products. Keep all caustic chemicals including
chlorine and pool cleaning products away from
stainless steel at all times.
This unit is equipped with an interior LED light which
will be turned ON when the door is open and the
interior fan is stopped at the same time. You can
press to manually turn on or turn o the light.
An audible alarm sounds if the storage temperature is
not cold enough. The temperature display flashes at
the same time.
The cause of the temperature being too high may be:
• Too much warm ambient air flow when rearranging
and removing stored items.
• Prolonged power failure.
• The appliance is faulty.
The audible alarm is automatically silenced and
the temperature display stops flashing when the
temperature is suciently cold again.
Periodic cleaning and proper maintenance will ensure
eciency, top performance and long life.
The maintenance intervals listed are based on normal
conditions. You may want to shorten the intervals if
you have pets or other special considerations.
Exterior cleaning for your stainless steel model:
• Turn o the power, unplug the appliance, and
remove all items – including the dispense kit.
• Wash the inside surfaces with warm water and
baking soda solution. The solution should be
appoximately 2 tablespoons baking soda by 1 quart
water.
• Wring excess water out of sponges or cloths when
cleaning controls or electrical parts.
• Wash the outside cabinet with warm water and mild
liquid detergent. Rinse and wipe dry with a clean
soft cloth.
• Do not use steel wool or a steel brush on the
stainless steel. These will contaminate the stainless
steel with steel particles and rusting may occur.
• Dust the front grill and back of the unit twice yearly,
making sure the power is o before cleaning.
• It is recommended to clean the unit yearly, inside
and out, to maximize the longevity of the product.
Before connecting the unit to the power source, let it
stand for approximately 24 hours. This will reduce the
possibility of malfunction in the cooling system from
handling during transportation.
1. Position the unit on a flat, level surface capable of
supporting the entire weight of the unit. Remember
the unit will be significantly heavier once it is fully
loaded.
2. Connect the unit to a Ground Fault Interrupter (GFI).
3. The unit must be installed according to your local
codes and ordinances.
4. ELECTROCUTION HAZARD!
• Electrical Grounding Required - This appliance is
equipped with a three prong (grounding) polarized
plug for your protection against possible shock
hazards.
• NEVER remove the round grounding prong from
the plug.
• NEVER use a two prong grounding adapter.
Before Use:
5. Remove the exterior and interior packaging, but do
not remove any foam insulation surrounding the
pipes at the back.
6. Clean the interior surface with lukewarm water
using a soft cloth.
7. Place the unit on a flat, solid floor that is strong
enough to support it when it is fully loaded. To
level the appliance, adjust the rolling casters at the
bottom of the unit.
8. When moving your kegerator, please do not incline
it more than 45 degrees.
9. Locate the appliance away from direct sunlight
and sources of heat (stove, heater, radiator, etc.).
Direct sunlight may aect the acrylic coating and
heat sources may increase electrical consumption.
Extreme cold ambient temperatures may also
cause the unit to perform improperly. The optimal
ambient temperature range is 50°F - 109.4°F. Do
not mount the draft tower remotely, as the exposed
beer line will not be refrigerated, causing foam.
10. Avoid locating the unit in damp areas.
11. Unwind the power cord to its full length and
inspect for damage before plugging into the outlet.
12. Plug the kegerator into an exclusive, properly
installed and grounded wall outlet.
13. Do not under any circumstances cut or remove
the third (ground) prong from the power cord.
Any questions concerning power and/or electrical
grounding should be directed to a certified
electrician or authorized products service center.
14. After plugging the appliance into a wall outlet,
allow the unit to cool down for 3 to 4 hours before
installing a keg in the appliance.
It is recommended that you install the appliance
in a place where the ambient temperature is
between 50°F and 109.4°F (10°C-43°C). If the ambient
temperature is above or below recommended
temperatures, the performance of the unit may
be aected. For example, placing your unit in
extremely cold or hot conditions may cause interior
temperatures to fluctuate. The operating temperature
range may not be reached.
Disconnect all power supplies and batteries
before servicing.
ELECTRICAL PARTS & COMPONENTS
WARNING
DEFROSTING
The unit defrosts automatically in normal operating
conditions. The evaporator behind the rear wall of
the unit defrosts automatically. The condensation
collects in the drainage channel behind the rear wall
of the unit and flows through the drainage hole into
the drop tray by the compressor where it evaporates.
However, frost may accumulate on the evaporator
if the unit is repeatedly opened in a high heat or
high humidity location. If this frost pattern does not
clear within 24 hours, your unit will require manual
defrosting.
Press and hold for 6 seconds to defrost the unit.
To stop defrosting, repeat the same interaction.
Important
BEFORE USING YOUR APPLIANCE
Remove the exterior and interior packing. Before
connecting the appliance to the power source, let it
stand upright for approximately 24 hours. This will
reduce the possibility of a malfunction in the cooling
system from handling during transportation. Clean
the interior surface with lukewarm water using a soft
cloth.

3KEGERATOR USER MANUAL 4
Then, attach the regulator to the CO2 tank, using an
adjustable wrench to avoid leakage. Place a metal
fastener around the neck of the red hose, and attach
the hose to the nozzle of the regulator. Tighten the
fastener using a flathead screwdriver. Place another
metal fastener around the other end of the red hose,
and attach to the nozzle on the Keg Coupler. Tighten
the metal fastener. Twist counterclockwise to open the
CO2 tank. Unscrew the pressure valve until loose, and
then re-screw until the pressure gauge reads “12”
Locate the translucent hose connected to the Keg
Tower, and attach it to the Keg Coupler. Then, connect
the Keg Coupler to your keg by pushing down and
twisting clockwise to lock it in.
Then, guide the translucent hose through the kegerator
opening, or if you have an island, as shown, guide it
through both openings. If mounting to a counter-top,
secure your tower using the four long bolts & nuts,
and 2 rubber washers. If mounting directly onto your
kegerator, use the 4 short bolts and metal washers.
The Kegerator is able to maintain the proper
dispensing temperature for beer, provided it is
installed correctly in the proper environment. For
best results, mount the draft tower as close to the top
of the kegerator as possible and seal any openings
to prevent heat transfer. Avoid opening and closing
the door of the kegerator too often to ensure a
consistent temperature inside the unit. Factory preset
temperature is 36 degrees Fahrenheit.
The Kegerator should be placed in an area where
the ambient temperature range is between 50-
109.4 degrees Fahrenheit (10-43 degrees Celsius).
If the ambient temperature is above or below this
range, the performance of the unit may be aected.
For example, placing your unit in extreme cold or
hot conditions may cause interior temperatures
to fluctuate. Please be aware that the desired
temperatures may fluctuate depending on the
ambient temperature and the orientation of the keg.
Press first, then press or button
to increase (warm) or decrease (cool) the set
temperature by 1°C/ 1°F.
Press again, the temperature is selected and
shows the actual temperature. If no other further
operation in 6 seconds, display will show actual
temperature in the cooler
The temperature you are setting will increase by
one degree each time you press the key and
will decrease by one degree each time you press
the key.
The range of temperature control is from 32°F to 50°F.
To view the set temperature at any time, press
the key. The set temperature will flash in the
display window for 6 seconds. After 6 seconds, the
temperature inside the until will reappear in the
display window.
(The temperature preset at the factory is 36°F)
CONTROL PANEL
°F/°C SELECTOR
SETTING THE TEMPERATURE CONTROL
OPERATION INSTRUCTION
ON/OFF POWER
To turn the appliance ON or OFF, press and hold the
POWER key for 5 seconds.
UP AND DOWN
SET
SET
SET
SET
Selects the temperature display setting in Fahrenheit
or Celsius degrees. To change the temperature from
Fahrenheit to Celsius or from Celsius to Fahrenheit,
press and at the same time, then hold for 6
seconds.
Unpackage your kegerator and lay out the kegerator
parts on a flat surface, ensuring you have the following:
STEP 1
STEP 2
5. Keg Tower w/Hose
6. Red Hose w/ 2 Fasteners
7. 4 Short Bolts &
4 Metal Washers
1. CO2 Regulator
2. Keg Coupler
3. Keg Tap & Handle
4. CO2 Tank
8. 4 Long Bolts, 4 Nuts &
2 Rubber Washers
9. Tap Tray
10. Keys
1
3
4
6
5
7
8
9
2
Now, screw the tap handle onto the Keg Tap, and fasten
the Keg Tap to the tower by rotating counterclockwise.
STEP 3
Place your CO2 tank onto the shelf, and then
lift the keg into the kegerator. Tap your keg by
pulling out the black lever of your Keg Coupler,
pushing down, and releasing. Make sure your keg
completely cools before use. Place the Tap Tray
below the tap.
POUR AND ENJOY!
STEP 6
*DO NOT PUSH DOWN THE BLACK LEVER ON KEG COUPLER*
STEP 4
STEP 5
INSTALLATION
OPERATING YOUR APPLIANCE

5KEGERATOR USER MANUAL 6
This appliance should be properly grounded for your
safety. The power cord of this appliance is equipped
with a three-prong plug which mates with a standard
three-prong wall outlet to minimize the possibility of
electrical shock.
Do not under any circumstance cut or remove the
third (ground) prong from the power cord supplied.
For personal safety, this appliance must be properly
grounded. Any questions concerning power and/
or grounding should be directed toward a certified
electrician or an authorized service center.
The appliance requires a standard 115/220 Volt AC-
60HZ three-prong grounded electrical outlet. Have
the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded. When a standard 2-prong wall outlet is
encountered, it is your responsibility and obligation
to have it replaced with a properly grounded 3-prong
wall outlet.
To prevent accidental injury, the cord should be
secured behind the appliance and not left exposed
dangling.
The appliance should always be plugged into
its own individual electrical outlet which has a
voltage rating that matches the rating label on the
appliance. This provides the best performance and
also prevents overloading house wiring circuits that
could cause a fire hazard from overheating. Never
unplug the appliance by pulling on the power cord,
always grip the plug firmly and pull straight out from
the receptacle. Repair or replace immediately all
power cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks
or abrasion damage along its length or at either
end. When moving the appliance, be careful not to
damage the power cord.
Because of potential safety hazards under certain
conditions, it is strongly recommended that you
do not use an extension cord with this appliance.
However, if you must use an extension cord it is
absolutely necessary that it be a UL/CUL-Listed,
3-wire grounding type appliance extension cord
having a ground type plug and outlet and that the
electrical rating of the cord be 115 volts and at least
1.3 amperes.
REPLACE ALL PANELS BEFORE OPERATING EXTENSION CORD
This appliance includes a stainless-steel handle that
is not required to operate this unit. To install the
handle please follow the below instructions:
1. Pull away the door gasket in the area where the
handle is to be installed as shown in illustration.
The gasket is easily displaced by hand, no tools
are necessary.
2. Locate the screws included in the bag with the
user’s guide. Insert the screws into the holes as
shown.
3. Align the handle with the screws installed.
Tighten the screws using a Phillips head
screwdriver until the handle sets both flush and
secured tightly against the door frame. (DO NOT
overtighten as this will cause damage to the
handle assembly).
4. Replace the door gasket to its original Position.
INSTALLING THE STAINLESS STEEL HANDLE
INSTALLATION
Improper use of the grounded plug can result
in the risk of electrical shock. If the power
record is cord is damaged, have it replaced by a
qualified or an authorized service dealer.
WARNING

7KEGERATOR USER MANUAL 8
GOLD STANDARD WARRANTY
Your investment in AMD Direct product is backed by the strongest warranty in
the industry. In addition to precision engineering and outstanding performance,
AMD Direct products include our GOLD STANDARD LIFETIME WARRANTY with
all replacement parts 100% non-prorated. Eective with purchases 8/1/21.
AMD Direct Warranty is valid for original purchaser at original site of delivery with
proof of purchase and photo documentation only. Registration form must be
submitted online within 30 days of the purchase date to validate the warranty.
Warranty is void upon transfer of ownership. Warranty does not apply to products
installed in any commercial, rental, or nonresidential application (exception of the
Resort Grill, Alturi, & TRL). Warranty covers replacement parts only. Manufacturer
is not responsible for labor or labor-related costs. Warranty does not cover
discoloration, surface rust, corrosion, or oxidation, which may occur due to harsh
environments, chemicals, or overheating. Warranty will not apply for damage
resulting from improper installations, abuse, extreme environments, grease fires,
or misuse. Proof of regular and proper maintenance is required. Coastal, humid,
and/or salt environments are subject to manufacturer review. All out-of-box claims
must be made within 30 days of purchase and must be made prior to installation.
Any product installed damaged will be considered damaged during installation
and not covered under warranty. Warranty and registration forms are available at
www.amddirect.com/register. Please be advised - all display models are sold “as
is” and the warranty covers the following items only: main burners (Gold Standard
Lifetime Warranty), grates (Gold Standard Lifetime Warranty), burner covers (Gold
Standard Lifetime Warranty). All warranties are subject to the review and approval
of the manufacturer.
14520 DELTA LANE SUITE 105,
HUNTINGTON BEACH, CA 92647
800.966.8126
AMDDIRECT.COM
AMD DIRECT GAS APPLIANCES
(GRILLS, SIDE/POWER BURNERS, & OVEN)
• Gold Standard Lifetime Warranty on construction and
manufacturer defects
• Gold Standard Lifetime Warranty on stainless steel construction
• Gold Standard Lifetime Warranty on cooking grates, burners, burner covers, valves,
flame tamers, and heatzone separators, temperature gauges, & hood springs
• Gold Standard Lifetime Warranty on briquette systems
• 3 YEAR Warranty on all other parts, components, & electrical, including: LED bulbs,
wire harness, & switches; power source wire; transformer; interior halogen light
wire & bulb
DRAWERS, DOORS, GRILL LINERS, & CARTS
• Gold Standard Lifetime Warranty on construction, workmanship and materials for all stainless
steel parts, including doors, drawers, grill liners, & carts
• 3 year on electrical (Warming Drawers)
COVERS
• Gold Standard Lifetime Warranty on covers, including grills,
carts, side/power burners & oven
MADERA PRODUCTS
• Gold Standard Lifetime Warranty on construction, workmanship and materials for all stainless
steel parts, hinges, drawer slides, gasket, & magnets
COMMERCIAL APPLICATIONS
RESORT, ALTURI & TRL GRILLS
• Gold Standard Lifetime Warranty on workmanship, construction, & manufacturer
defects for all commercial and/or hospitality applications
• Warranty is void upon misuse, including lack of regular cleaning, vandalism, or theft
• Warranty is valid only if regular maintenance is exercised. Due to the nature of
commercial applications (multiple users, lack of control of use, etc.) regular
maintenance is mandatory
VENT HOODS, REFRIGERATION,
COLD STORAGE & SINKS
VENT HOODS
• 5 Year Warranty on all Stainless Steel Construction
• 3 year Warranty on blowers, LED Lighting, wiring harness and switches
15" & 24" REFRIGERATION MODELS
• 3 year Warranty on all construction including compressors
• 1 year Warranty on transformer, LED bulbs, LED harness, power source wire, LED
switches, interior halogen light wire/bulbs
21" REFRIGERATION MODELS
• 1 year Warranty on all construction & electrical components including compressor,
transformer, LED bulbs, LED harness, power source wire, LED switches, interior
halogen light wire/bulbs
COLD STORAGE & SINKS
• Gold Standard Lifetime Warranty on Ice Chests
• Gold Standard Lifetime Warranty on drains & faucets
GOLD STANDARD
LIFETIME
WARRANTY

CONTACT US
14520 Delta Ln,
Suite 105
Huntington Beach, CA 92647
AMDDirect.com
[phone]
M–F 8:30 am – 5:00 pm (PST)
VER.41622