AME 67601 User manual

INSTRUCTION MANUAL
AME INTERNATIONAL - 2 - WWW.AMEINTL.NET
Models 67601 & 67751
Break-A-Way Torque Wrench
WARNING: IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL. IT IS
THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE
INFORMATION IN THIS MANUAL INTO THE HANDS OF THE
OPERATOR. FAILURE TO OBSERVE THE FOLLOWING
WARNINGS COULD RESULT IN INJURY.
WARNING: IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL. IT IS
THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE
INFORMATION IN THIS MANUAL INTO THE HANDS OF THE
OPERATOR. FAILURE TO OBSERVE THE FOLLOWING
WARNINGS COULD RESULT IN INJURY.
2347 Circuit Way, Brooksville, Florida, USA 34604
Phone: [phone] Toll Phone: [phone]AME (4263)
Fax: [phone] E-mail: [email protected] www.ameintl.net
2347 Circuit Way, Brooksville, Florida, USA 34604
Phone: [phone] Toll Phone: [phone]AME (4263)
Fax: [phone] E-mail: [email protected] www.ameintl.net
AME International’s 1-Year Limited Warranty
AME International products are warranted against defects in material
and workmanship for one year from the date of purchase. The product
must be operated, maintained and installed according to the instructions
and procedures provided, or this warranty is void. Any modication or
wrongful use of the product will also void this warranty. AME International’s
obligation under this warranty is limited to the repair or replacement of
defective products. For more information or to inquire about this warranty,
please contact our ofce @ 352-799-1111 or email [email protected].

AME INTERNATIONAL - 2 - WWW.AMEINTL.NET AME INTERNATIONAL - 3 - WWW.AMEINTL.NET
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions.
297*210mm
150-600 Ft.Lbs / 200-750 Ft.Lbs
Do not use this wrench as a
hammer or pry bar.
22mm wrench
To avoid inaccurate torque,
do not fully remove the nut.
Release the adapter by pushing
or pulling from center of the head.
To torque, grasp the handle and push downward.
A break-a-way indicates that the desired pre-set
torque has been met.
Lubricate three points
frequently.
The handle should align with
the desired torque.
Using a 22 MM wrench, adjust
the torque measurement to the
desired torque.
Torque wrench mechanism will break-a-way when desired
torque is met. Do not continue to apply pressure after desired
torque is met.
※
※
230ft.lb
To avoid inaccurate torque or damage to
the tool, do not install
unnecessary
extensions
.
Models 67601
& 67751
Break-A-Way
Torque Wrench
Instructions