AME Fasy-Flate 24868 User manual

Part No. 24868
PSI

2
Digital Automatic Tire Inflator (Portable)
Thank you for selecting our Digital Automatic Tire Inflator (Portable),
please read this manual carefully before using.
This manual is an integral and essential part of the product, please keep
it away from damp, heat, dust, oils, do not remove, tear or amend any
parts of the manual for any reason. It must be made available to the
operator and to maintenance personnel, also to ensure staff training. In
case of loss or damage, ask the manufacturer for a copy. The manual
must always remain with the device, in the event of the device being
sold, it must be given to the new user.
The supplier reserves the right to change product features at
any time.

3
Table of Contents
Components List 4
Features 5
Introduction 5
Control Panel 5-6
Function and Operation 6-7
Troubleshooting 8
Maintenance 9
Specications 10
Calibration Certicate 11
Instruction Manual

4
Components List
■Inator
■Hose: 5 ft
PSI
■1/4 '' BSP to 1/4 '' NPT adaptor
■Hot shoes* and charger
AU, UK, EURO, USA
■Instruction manual
Part No. 24868
PSI
* Illustrative purposes only ✔

5
Features
■Auto-off after 90 seconds
■Max. Pressure 174 p.s.i.
■Ideal for cars, trucks, bikes etc
■Large easy to read LCD display
with audible warning
■Rechargeable Lithium-Ion battery
■Tough ABS case
■Individually calibrated and tested
(see calibration certicate pg 11)
Introduction
Through the manual the following
symbols will be used, this information
is for your safety and to prevent
damage to this product.
The hazard or unsafe
practice could result in
minor injury
WARNING
The hazard or unsafe
practice could result in
severe injury or death
WARNING
Control Panel
PSI
Button Function
(P1): Programmable button
(Initial value 15 p.s.i.)
(P2): Programmable button
(Initial value 30 p.s.i.)
(ON/OFF/LIGHT): Power on/
Power off/Light
(+): Increase target pressure,
Unit Change, Manual ination
(-): Reduce target pressure,
Unit Change
(SET): Function Select: Unit Change/
OPS set/Manual ination
Instruction Manual

6
LCD Display
1. Unit display
2. Pressure display
3. Function select display
4. Working indicator
Function and Operation
This device includes the OPS
(Over Pressure Setting) function used to
inflate and seat tires on the rim.
Operation
SET OPS
KPA
BAR
PSI
KGF
2. Set OPS (Over Pressure Setting)
2.1. Press (SET) once, (SET) and (OPS)
will be shown on the LCD screen,
(OPS) will be ashing.
2.2. Press (+) or (-) to choose the
OPS value.
2.3. Press (SET) to confirm. If
OPS value is not zero, (OPS) will
be displayed at the LCD screen.
3. Manual inflation
If tire pressure is lower than 3 p.s.i. or 0.2
bar, the device will not start automatically.
3.1. Press (SET) twice, the
current pressure will be shown
on the LCD screen.
3.2. Press (+) to start manually.
4. Set programmable buttons
(P1) initial value is 15 p.s.i. /1 bar, (P2)
initial value is 30 p.s.i. /2.1 bar. The preset
pressure value can be reset by the user,
setting it here will save it for following
usage. But it reverts to the initial value
after a unit set change.
1. Press (P1) or (P2), (P1) preset value or
(P2) preset value will be shown on the
LCD screen.
2. Press (+) or (-) to choose preset
pressure value.
3. Press (SET) to conrm.
1. Unit select
Device has four units can be chosen by the
user which is kpa-psi-bar-kg/cm2.
Unit set here will become default unit for
following usage, do not need to set unit
each time.
1.1. Press (SET), (SET) will be shown
on the LCD screen, and the unit
will be flashing.
1.2. Press (+) or (-) to choose the
unit.
1.3. Press (SET) to confirm.

7
5. Ination and Deation
1. Press (P1) or (P2) to select default preset
pressure.
2. Press (+) or (-) to adjust target pressure.
3. Connect with tire, ensure no air leaks,
inflator will start automatically.
4. When inflation is finished, the device will
stop automatically and BEEP to remind
the user.
5. Disconnect the air hose from tire.
6. Power on/Power off/Backlight
When battery indicator is ashing on the
LCD screen please recharge the battery.
Press (ON/OFF/LIGHT) two seconds to
turn on,
Press (ON/OFF/LIGHT) to turn on backlight
when the device is on,
Press (ON/OFF/LIGHT) for three seconds
to turn off.
Notes:
1. Press (SET) to enter the (OPS) setting.
2. Press (SET) four times and the device
will exit out of the setting mode without
saving any selection.
3. When OPS function is selected the
device will inflate to target pressure plus
the OPS value first, then deflate to tire
pressure desired, for example: A final
target of 32 p.s.i. with an OPS setting of
16 p.s.i. gives a sum of 48 p.s.i. This
sum of 48 p.s.i. is the Over Pressure
Setting for tire. The tire will inflate to the
sum value and deflate to the final target
pressure.
4. During ination, the device will check
tire pressure automatically, the working
indicator will be on, left to right means
inating, right toleft means deating.
To avoid the risk of
personal injury, especially
to the eyes, face or skin.
DO NOT direct the air
stream at any person
WARNING
This equipment is not
intended for use by
children without adult
supervision
WARNING
When using the OPS
function the sum pressure
must not exceed the tire
manufacturer’s maximum
inflation pressure.
WARNING
Instruction Manual

8
Troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
Air leak Leak in the connection Check the Connection
The inator works,
but no air is owing
Obstruction in lters or in
air system
Clean the lters and
check the air source
No display Flat battery Recharge battery
Ination does not start,
although the pressure is set
and the hose is connected
with tire
Air hose improperly connected
Check the hose
connection, make sure
that no air leaks
Tire pressure is below
3 p.s.i. Manual ination
Err1 Pressure sensor broken Power off, change
pressure sensor
Err2 Unstable pressure,
faulty hose connector
Replace hose connector or
re-connect hose to the tire
Err3 Connected tire pressure is
too high 180 p.s.i. Stop inflating this tire
Err4 Wrong connections at air inlet
and outlet
Refer to wiring diagram and
connect magnetic valve
accordingly
Err8 Air supply lower than set
inate pressure Stop inflating this tire
8
Err5 Low battery Plug in unit to recharge the
battery

9
INSTRUCTION MANUAL
Maintenance
The device does not require particular maintenance, routine check of the air connections
is suggested.
In the event that maintenance is required it should be carried out by qualied personal.
Note
This unit must be used with clean dry air. Therefore an air lter must be used with this
unit to ensure its continued reliability.
9
Instruction Manual

10
Specications
■Scale
174 p.s.i.
■Accuracy
+/-0.3 p.s.i.
■Max Inlet Air Supply
180 p.s.i.
■Supply Voltage
DC 12V rechargeable battery (Li-ION)
■Charger Voltage
AC 110~240 V (50~60Hz)
■Watt
12W Max.
■Working Temperature
-10~50°C (14~122°F)
■Auto Off
90 seconds
■Hose Length
5 ft (1.5 m)
■Inlet Size
1/4 '' NPT
■Chuck Type
Clip on
■Chuck Style
Single straight
■Reader Unit
Digital display with audible warning
■Dimensions
19.96 x 4.92 x 5.3 in.
(380 x 125 x 135 mm)
■Weight
4.4 lbs (2 kg)
■Operation
Auto inflate/deflate
■Inflation Flow
2500 l/m @ 145 p.s.i.
■Work Time Hrs
10-15hrs (from fully charged
continual use)

11
Calibration Certificate
This Digital Automatic Tire Inflator has been calibrated in its normal working position on
test equipment with anaccuracy that istraceable toInternational Standards according
to: 86/217/EEC.
ALLOWABLE TOLERANCE
p.s.i.
±1.2 up to and including 58 p.s.i.
±2.3 between 58 and 145 p.s.i. inclusive
±3.6 greater than 145 p.s.i.
TEST RESULT
REFERENCE PRESSURE
BAR P. S.I.
DISPLAY PRESSURE
BAR P. S. I .
Serial Number:
Date:
Instruction Manual

Product No. 24868