Amensolar N3H-X3.6-US User manual

USER MANUAL
Hybrid Inverter User Manual

CONTENTS
1 Notes on this Manual ..................................................................................... 1
1.1 Scope of Validity .........................................................................................1
1.2 Target Group ............................................................................................. 1
1.3 Symbols Used ............................................................................................ 1
2 Safety ......................................................................................................... 2
2.1 Important Safety Instructions ...................................................................... 2
2.2 Explanation of Symbol .................................................................................5
3. Introduction .................................................................................................7
3.1 Basic features ............................................................................................ 7
3.2 System Diagram .........................................................................................7
3.3 Work Modes ............................................................................................. 13
3.4 Dimension ............................................................................................... 14
3.5 Terminals of PV inverter ............................................................................ 15
4. Technical Parameters .................................................................................. 17
4.1 Inverter specification .................................................................................17
5. Installation ................................................................................................ 19
5.1 Check for Physical Damage ........................................................................ 19
5.2 Packing List ............................................................................................... 19
5.3 Mounting................................................................................................... 20
6. Electrical Connection ...................................................................................23
6.1 PV connection ...........................................................................................23
6.2 Grid Connection (GEN connection) .............................................................. 24
6.3 Back-up:Load1 and Load2 Connection .......................................................... 24
6.4 Battery Connection ................................................................................... 27
6.5 WiFi Connection (optional) ......................................................................... 28
6.6 GPRS Connection (optional) ....................................................................... 29
6.7 CT Installation instruction .......................................................................... 30
7. Inverter Parallel Guide ................................................................................ 31
7.1 Parallel System Diagram ............................................................................31
7.3 Parallel Operation Notes ............................................................................ 33
7.4 Parallel System Setting ..............................................................................33
8. Generator Operation Guide .......................................................................... 35
8.1 Generator Use Diagram ............................................................................. 35
8.2 Generator Operation Notes ........................................................................ 36
8.3 Generator Setting ..................................................................................... 37
9. LCD Operation ........................................................................................... 38
9.1 Control Panel ............................................................................................38
9.2 Instructions for LED Indicator .....................................................................38
9.3 Instructions for the use of three modes ....................................................... 39
9.4 LCD Interface ........................................................................................... 41
9.5 SETTING ..................................................................................................45

9.6 INQUIRE ..................................................................................................55
9.7 STATISTIC ............................................................................................... 56
10. WIFI Quick Guide ......................................................................................57
10.1 Stick Logger Quick Guide ......................................................................... 57
10.2 USER MANUAL for SOLARMAN Smart APP ...................................................60
11. Notes for turn on inverter .......................................................................... 64
12. Fault diagnosis and solutions ......................................................................65

1
Danger ！
“Danger” indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Warning!
“Warning” indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
Caution ！
“Caution” indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.
Note ！
“Note” provides tips that are valuable for the optimal operation of our
inverter.
1 Notes on this Manual
1.1 Scope of Validity
This manual is an integral part of Hybrid, It describes the assembly, installation,
commissioning, maintenance and failure type of the product. Please read it carefully
before operating.
N3H-X3.6-US
N3H-X5.0-US
N3H-X6.0-US
N3H-X8.0-US
N3H-X10.0-US
Naming rules, For example: N3H-X7.6-US
“7.6” means “output power 7.6kw”.
“US” means “for North America market”
Store this manual where it will be accessible at all times.
1.2 Target Group
This manual is for qualified electricians. The tasks described in this manual only can be
performed by qualified electricians.
1.3 Symbols Used
The following types of safety instructions and general information appear in this
document as described below:

2
Danger!
Danger to life due to high voltages in the inverter!
All work must be carried out by qualified electrician.
The appliance is not to be used by children or persons with reduced
physical sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
Children should be supervised to ensure that they do not play with the
appliance.
Caution!
Danger of burn injuries due to hot enclosure parts!
During operation, the upper lid of the enclosure and the enclosure body
may become hot.
Only touch the lower enclosure lid during operation
Caution!
Possible damage to health as a result of the effects of
radiation!
Do not stay closer than 20 cm to inverter for any length of time.
Note!
Grounding the PV generator
Comply with the local requirements for grounding the PV modules and
the PV generator. It is recommends connecting the generator frame and other electrically
conductive surfaces in a manner which ensures continuous conduction and ground these in
order to have optimal protection of system and persons.
Warning!
Ensure input DC voltage ≤Max. DC voltage. Over voltage may cause
permanent damage to inverter or other losses, which will not be
included in warranty!
2 Safety
2.1 Important Safety Instructions

3
Warning!
Do not operate the inverter when the device is running .
Warning!
Risk of electric shock!
Warning!
Authorized service personnel must disconnect both AC and DC power
from inverter before attempting any maintenance or cleaning or
working on any circuits connected to inverter.
 Please keep the user manual properly. When operating equipment, in addition to
following the general precautions in this document, follow the specific safety
instructions. We will not be liable for any consequence caused by the violation of the
safety operation regulations and design, production, and usage standards.

Accessories only together with the inverter shipment are recommended here.
Otherwise may result in a risk of fire, electric shock, or injury to person.

Make sure that existing wiring is in good condition and that wire is not undersized. Do
not disassemble any parts of inverter which are not mentioned in installation guide.
It contains no user-serviceable parts. See Warranty for instructions on obtaining
service. Attempting to service the inverter yourself may result in a risk of electric
shock or fire and will void your warranty.

Keep away from flammable, explosive materials to avoid fire disaster.
 The installation place should be away from humid or corrosive substance.
 Authorized service personnel must use insulated tools when installing or working
with this equipment.
 Never touch either the positive or negative pole of PV connecting device. Strictly
prohibit touching both of them at the same time.

The unit contains capacitors that remain charged to a potentially lethal voltage after
the MAINS, battery and PV supply has been disconnected.

Hazardous voltage will present for up to 5 minutes after disconnection from power
supply.

CAUTION-RISK of electric shock from energy stored in capacitor. Never operate on
the inverter couplers, the MAINS cables, Battery cables, PV cables or the PV
generator when power is applied. After switching off the PV, battery and Mains,
always wait for 5 minutes to let the intermediate circuit capacitors discharge before
unplugging DC, battery in plug and MAINS couplers.

4
WARNING !
Over-voltage protection with surge arresters should be provided when the
PV power system is installed.
The grid connected inverter is not fitted with SPDs in both PV input side
and MAINS side.
 When accessing the internal circuit of inverter, it is very important to wait 5 minutes
before operating the power circuit or demounting the electrolyte capacitors inside the
device. Do not open the device before hand since the capacitors require time
sufficiently discharge!

Surge protection devices (SPDs) for PV installation
 Lightning will cause a damage either from a direct strike or from surges due to a
nearby strike.

Induced surges are the most likely cause of lightning damage in majority or
installations, especially in rural areas where electricity is usually provided by long
overhead lines. Surge may be included on both the PV array conduction and the AC
cables leading to the building.
 Specialists in lightning protection should be consulted during the end use application.
Using appropriate external lightning protection, the effect of a direct lightning strike
into a building can be mitigated in a controlled way, and the lightning current can be
discharged into the ground.
 Installation of SPDs to protect the inverter against mechanical damage and excessive
stress include a surge arrester in case of a building with external lightning protection
system (LPS) when separation distance is kept.
 To protect the DC system, surge suppression device (SPD type2) should be fitted at
the inverter end of the DC cabling and at the array located between the inverter and
the PV generator, if the voltage protection level (VP) of the surge arresters is greater
than 1100V, an additional SPD type 3 required for surge protection for electrical
devices.
 To protect the AC system, surge suppression devices (SPD type2) should be fitted at
the main incoming point of AC supply (at the consumers cutout), located between
the inverter and the meter/distribution system;

All DC cables should be installed to provide as short a run as possible, and positive
and negative cables of the string or main DC supply should be bundled together.
Avoiding the creation of loops in the system.

Spark gap devices are not suitable to be used in DC circuits once conducting, they
won’t stop conducting until the voltage across their terminals is typically more than
30 volts.
 Anti-Islanding Effect

5
WARNING !
High leakage current!
Earth connection essential before connecting supply.
Islanding effect is a special phenomenon that grid-connected PV system still supply
power to the nearby grid when the voltage loss is happened in the power system. It is
dangerous for maintenance personnel and the public.
Hybrid series inverter provide Active Frequency Drift(AFD) to prevent islanding effect.
 PE Connection and Leakage Current
The end-use application shall monitor the protective conductor by residual current
operated protective device (RCD) with rated fault current Ifn≤240mA which
automatically disconnects the device in case of a fault.
The device is intended to connect to a PV generator with a capacitance limit of approx
700nf.
Incorrect grounding can cause physical injury, death or equipment malfunction and
increase electromagnetic.
 Battery Safety Instructions
Hybrid Series inverter should be worked with low voltage battery, for the specific
parameters such as battery type, nominal voltage and nominal capacity etc., please refer
to section 4.3.
As accumulator batteries may contain potential electric shock and short-circuit current
danger, to avoid accidents that might be thus resulted, the following warnings should be
observed during battery replacement:
1: Do not wear watches, rings or similar metallic items.
2: Use insulated tools.
3: Put on rubber shoes and gloves.
4: Do not place metallic tools and similar metallic parts on the batteries.
5: Switch offload connected to the batteries before dismantling battery connection
terminals.
6: Only personal with proper expertise can carry out the maintenance of accumulator
batteries.
2.2 Explanation of Symbol
This section gives an explanation of all the symbols shown on the inverter and on the type
label.
Symbols on the Type Label

6
CSA certified
This symbol indicates that you should wait at least 5 mins after disconnecting the
inverter from the utility grid and from the PV panel before touching any inner live
parts.
Keep dry! The package/product must be protected from excessive humidity and
must be stored under cover.
Refer to the operating instructions.
Fragile - The package/product should be handled carefully and never be tipped over
or slung.
Products should not be disposed as household waste.
No more than six(6) identical packages being stacked on each other
Components of the product can be recycled.
Danger of hot surface!
Danger of high voltage and electric shock!
Caution! Failure to observe a warning indicated in this manual may result in injury!

7
Note!
Please control the home loads, and make sure it’s within the “BACK-UP
output rating” under BACK-UP mode, otherwise the inverter will shut
down with an “overload fault” warning.
Please confirm with the mains grid operator whether there is any
special regulations for grid connection.
3. Introduction
3.1 Basic features
Hybrid Series is a high-quality inverter which can convert solar energy to AC energy and
store energy into battery.
The inverter can be used to optimize self-consumption, store in the battery for future use
or feed in to public grid. Work mode depends on PV energy and user’s preference. It can
provide power for emergency use during the grid lost by using the energy from battery
and inverter (generated from PV).
3.2 System Diagram
Hybrid Series is designed with two BACK-UP versions for customer to choose based on
the local rules.The applies to the wiring rules that requires Neutral line of alternative
supply must NOT be isolated or switched .

10

11
All switches and RCD devices in the figure are for reference only, and the specific
installation shall be subject to local regulations.
Note!
Please control the home loads, and make sure it’s within the “BACK-UP output
rating ” under BACK-UP mode, otherwise the inverter will shut down with an
“overload fault” warning.
Please confirm with the mains grid operator whether there is any special regulations
for grid connection.

12
Note!
The arrow on the CT points to the power grid, as shown.
If the CT connector is improperly connected, the inverter cannot read the data
correctly, so that the relevant working conditions cannot be realized normally.

13
3.3 Work Modes
Inverter provides multiple work modes based on different requirements.

14
3.4 Dimension

15
WARNING !
Qualified electrician will be required for the installation.
3.5 Terminals of PV inverter
Object
Description
A
DC switch
B
BAT input
C
WiFi
D
CAN1/CAN2/RS485/BMS485,BMSCAN/CTL1/CTL2/Type-c upgrade
E
PV1~PV4 input
F
Generator
G
Grid
H
BACK-UP1 output
I
PE
J
BACK-UP2 output
K
LCD
L
RSD button

16
* Port Function
CAN1/CAN2: Communication interface for connecting inverters.
RS485: Read the internal data of inverter.
BMS-485/ BMS-CAN: BMS communication for lithium batteries.
CT L1/CT L2: For external grid side CT to detect current size.
TYPE-C UPDATE: Update machine software locally on PC via USB-A port.

17
4. Technical Parameters
4.1 Inverter specification
Technical Data
N3H-X5.0-US
N3H-X6.0-US
N3H-X8.0-US
N3H-X10.0-US
PV Input Data
MAX.DC Input Power
7.5kW
9kw
12kw
12KW
NO.MPPT Tracker
4
MPPT Range
120 - 500V
MAX.DC Input Voltage
500V
MAX.Input Current
12A
Battery Input Data
Nominal voltage (Vdc)
48V
48V
48V
48V
MAX.Charging/Discharging Current
120A/120A
135A/135A
190A/190A
190A/190A
Battery Voltage Range
40-60V
Battery Type
Lithium and Lead Acid Battery
Charging Strategy for Li-Ion Battery
Self-adaption to BMS
AC Output Data(On-Grid)
Nominal output power Output to Grid
5KVA
6KVA
7.6KVA
8KVA
MAX. Apparent Power Output to Grid
5.5KVA
6.6KVA
8.4KVA
8.8KVA
Output Voltage Range
110-120/220-240V split phase, 1Ø, 230 1 phase
Output Frequency
50/60Hz（45 to 54.9Hz / 55 to 65Hz）
Nominal AC Current Output to Grid
20.8A
25A
31.7A
33.3A
Max.AC Current Output to Grid
22.9A
27.5A
35A
36.7A
Output Power Factor
0.8leading…0.8lagging
OutPut THDI
< 2%
AC Output Data(Back-Up)
Nominal. Apparent Power Output
5KVA
6KVA
7.6KVA
8KVA
MAX. Apparent Power Output
5.5KVA
6.6KVA
8.4KVA
8.8KVA
Nominal Output Voltage L-N/L1-L2
120/240V
Nominal Output Frequency
60Hz
Output THDU
< 2%
Efficiency
Europe Efficiency
>=97.8%
MAX. Battery to Load Efficiency
>=97.2%
Protection
Grounding detection
YES
Arc Fault Protection
YES
Island Protection
YES

18
Battery reverse Polarity
YES
Insulation Resistor Detection
YES
Residual Current Monitoring Unit
YES
Output Over Current Protection
YES
Back-up Output Short Protection
YES
Terminal temperature detection
YES
Output Over Voltage Protection
YES
Output Under Voltage Protection
YES
General Data
Output Conduit
25.4mm
PV Input Conduit
25.4mm
BAT Input Conduit
34.5mm
Operating Temperature Range
-25 ~ +60°C
Relative Humidity
0-95%
Operating Altitude
0~4000m
Ingress Protection
IP65/NEMA 3R
Weight
32kg
Size (Width*Height*Depth）
530mm x 660mm x 200mm
Cooling
Natural Convection
Noise emission
<38dB
Display
LCD
Communication With BMS/Meter/EMS
CAN，RS485
Supported communication interface
RS485, WLAN, 4G (optional)
Self-consumption at night
< 2.5 W (with battery enabling < 5 W)
Safety
UL1741SA all options, UL1699B, CSA 22.2
EMC
FCC Part 15 Class
Grid connection standards
IEEE 1547, IEEE 2030.5, Hawaii Rule 14H, Rule 21 Phase I,II,III

19
A
B
C
D
E
F
5. Installation
5.1 Check for Physical Damage
Make sure the inverter is intact during transportation. If there is any visible damage,
such as cracks, please contact your dealer immediately.
5.2 Packing List
Open the package and take out the product, please check the accessories first. The
packing list shown as below.
Object
Description
A
Inverter
B
Expansion screws and pan-head screws
C
CT
D
WiFi module (optional)
E
GPRS module (optional)
F
User manual