American DJ LASER-4800 User manual

American DJ ®LOS ANGELES, CA. 90058 USA
American DJ®OWNERS MANUAL
Thank you for purchasing this American DJ® product. Please read the following
Manual before installing or using your new unit.
VISIBLE LASER RADIATION
AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635-650 nm
MAX. OUTPUT : < 5 mW
CLASS llla LASER PRODUCT
DANGER
AVOID EXPOSURE
Laser light is emitted
from this aperture
This Laser product complies with the
CDRH/BRH radiation performance
standards. 21 CFR Subchapter J.
“DANGER - Laser radiation when
open. AVOID DIRECT EYE EXPO-
SURE.” For Class llla accessible laser
radiation with an irradiance greater
than 2.5 x 10-3 Wcm -2
Non Interlocking Housing Label
Certification Label
Aperture Label
CHDR Warning Label
Caution! No user serviceable parts inside do not attempt repairs. In the event your unit should fail, contact your
American DJ® dealer.
This Laser product complies with the CDRH/BRH Radiation Performance Standards. 21 CFR Subchapter J.
WARNING! This Product must not be used for audience scanning. To prevent fire or shock hazard, do not
expose this product to a high temperature or high humidity area.
WARNING: Never Look Directly INTO Laser Beam
CAUTION: Use of controls, adjustments, or procedures other
than those specified herein may result in hazardous
radiation exposure.
1. CHDR Warning Label
2. Projection Aperture
3. Remote receiving sensor
4. Aperture Label
5. Non Interlocking Housing Label
6. Mini plug External Power supply
7. Emission Indicator Switch
8. Shutter Control Switch
9. Power Switch
10.Identification Label
11.Battery Cover (bottom)
12.Mode Select
13.Connection for interlink cable
14.External sensor connection
15.Certification Label
6
5
3
1
2
7,8,910 1213 14
15
11
4

SPECIFICATIONS:
Diode: 5 mW,
Weight 3 lbs.,
Dimensions: 10.5” x 4.5” x 4.5”
Supply Voltage:9VDC With suppliedAC
120V adapter or AC 240V adapter must be
500ma min. or 4 C batteries(not supplied)
Wireless remote uses 2AA batteries
(Supplied)
Operating Instructions:
14. 3P Infrared Receiving Sensor socket
13. Series Control Left Input , Right Output
12. Function Mode (4) may be selected for Auto or Music Modes. NOTE: Must be selected
before turning on unit but it can be defeated by remote control.
Auto Mode: 24 pre-set geometric patterns to be executed in regular order.
Music Mode: 24 pre-set geometric patterns to executed in regular order, speed
is controlled by built-in microphone.
Additional Safety Notes: This is a laser product, please avoid direct eye exposure.
Take out all the batteries to avoid humidity damage. Do not expose this product
to high temperature or high humidity area.
Remote Control:
The Laser-4800 Comes with a remote control which allows you to control the speed,
type of design, music, manual or auto modes, and by pressing static and adjust dynamic but-
tons multiple times,or then pressing (+) (-) buttons and holding them down you can alter most
of the existing geometric patterns.
Master / Slave:
The Laser-4800 can be used in a master /slave configuration using cable available
from American DJ®. The only precautions are to observe the in and out configuration , and
cable should not exceed 300’.
Additional Safety Notes: This is a laser product, please avoid direct eye exposure. Take out
all the batteries, when not in use, to avoid humidity damage. Do not expose this product to
high temperature or humidity .
Caution! No user serviceable parts inside do not attempt repairs. In the event your unit should fail, con-
tact your American DJ® dealer.
™American DJ®
16. 24 Geometric Pattern
presets
17. Mode select
18. Static Dynamic
19. Adjust Dynamic
(pulsating image)
20. + ,- adjustments
21. Standby,
22. Emission indicator switch
23. Shutter control switch
16
17
18
19
20
21
22
23