American DJ LED OPERATOR User manual

User Instructions
Rev1.0
LED OPERATOR
RECORD
TAP SYNCSTROBE
BLACKOUT
PAGE 1
PAGE 2
PAGE
LED OPERATOR
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
RED
COLOR PRESETS CHASES
1 12 23 34 4
5 56 67 78 8
GREEN BLUE MASTER SPEED FADE
0.1S 30S
10Min 0

Functions:
-3 Channel, RGB LED Controller
-16 Color Presets
-Power failure memory
-1-
Product layout
Technical Specifications:
Power Input.................................................................................................................DC 9V, 200mA Min
DMX Out.......................................................................................................3-pin female XLR connector
Dimension............................................................................................9.64”x7”x2.36” (245X178X60mm)
Weight...............................................................................................................................3.2lbs. (1.45kg)
1R,G,B Faders: Use R,G,B faders to manually set the intensity of each relevant color.
3Record button: Use the Record button to engage record mode and record color presets and chases.
2MASTER Fader: Use Master fader to manually control overall intensity.
4Strobe button: Use the Strobe button to trigger strobe function at any time during playback.
5TAP SYNC button: Press the Tap Sync button twice during Chase playback to set Chase speed.
6
Black Out button: Press the Black Out button to cut all output.
7SPEED Fader: Use the Speed fader to manually set the chase speed during playback.
8FADE Fader: Use the Fade fader to manually set the chase fade rate during playback.
7
RECORD
TAP SY NCSTR OBE
BLACKOUT
PAGE 1
PAGE 2
PAGE
LED indicator OPERATOR
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
RED
COLOR PRESETS CHASES
1 12 23 34 4
5 56 67 78 8
GREEN BLUE MASTER SPEED FADE
0.1S 30S
10Min 0
6
4 51 2
9
10
12
11
38
9PAGE 1/2 LED indicators : Indicates the active Color Preset page. When Page 1 indicator is lit,
scenes 1-8 are active. When Page 2 indicator is lit, scenes 9-16 are active.
10 PAGE button: Use this button to switch between Color Preset pages 1 and 2.
11 Color preset buttons and LED indicators 1-8: Use these buttons to trigger relevant color presets.
12 Chase buttons and LED indicators 1-8: Use these buttons to trigger relevant chase presets.
-8 Preset Chases
-Strobe Function
-Individual RGB Channel Faders
-Grand Master Fader
-Record Function to Record Colors and Chases
-Speed & Fade faders for Chase control

Color Preset and Chase Playback
1. Adjust the Red, Green, Blue & Master faders to set
a scene on the fly as desired.
2.
You can also manually adjust the RED, GREEN and BLUE
faders to temporarily edit the current color. Adjust the fader to set the overall output intensity.
Select a by pressing buttons 1-8 in the Color Presets section. Press the
button to switch between color preset pages 1 and 2. When LED indicator illuminates, color
presets 1-8 are accessible; when LED indicator illuminates, color presets 9-16 are
accessible. When a color preset is selected, its LED indicator will continually flash. Press the same
color preset number button to disengage it.
“Color Preset” "PAGE"
"PAGE1"
"PAGE2"
"MASTER"
3. Select a " by pressing buttons 1-8 in the Chases section. When a chase is selected, its
LED indicator will flash continually. Additional chases can be selected and will playback in a sequential
fashion. When additional chases are selected, each relevant Chase LED will illuminate ON solid until
it becomes its turn to playback in the sequence. Pressing a selected chase button a second time will
disengage the relevant chase. Adjust the “MASTER” fader to set the overall output intensity.
"CHASE
Operating Instructions:
(1) Connect from your controllers DMX output to the DMX input of your first LED fixture in line.
(2) BLACKOUT mode is active by factory default. When first powering on LED Operator, the
LED indicator should be OFF.
"BLACKOUT" LED
indicator will illuminate. Press the "BLACKOUT" button once to disengage. The
(3) After the first use, LED Operator will default to its last state before being shut off.
-2-

(1) : Press and hold down the button and sequentiallyRecord Mode Enable "RECORD" press
" buttons 1, 6, 8, 1, 6, 8 then release the button. The LED indicator
will turn ON indicating that mode is engaged.
COLOR PRESET" "RECORD" RECORD
RECORD
Record mode
(2) Adjust the faders to set a
as desired.
RED, GREEN, BLUE & MASTER Color
Preset/Scene
(3) Press a button that you wish to save it to. Repeat step 2 and 3 to save additional
Color Presets/Scenes.
COLOR PRESET # (1-8)
(4) Press the button twice to exit“BLACKOUT” RECORD MODE.
+
+Or
SPEED
0.1S
10Min
FADE
30S
0
Adjust the and faders to manually set a desired chase speed and fade percentage.
You can also press the button twice continually to set a desired chase speed. The
“SPEED” “FADE”
“TAP SYNC”
TAP SYNC LED will flash at the rate that it was pressed..
(1) Engage Record mode as described above.
Record Custom Color Presets
NOTE:
FACTORY CHASES WILL NOT ACCEPT FADE CONTROL. FADE CONTROL WILL ONLY WORK WITH
CUSTOM (USER CREATED) CHASES.

Up to 8 chases can be programed, each of which can store up to 20 scenes/steps. Note: When recording custom
chases, relevant factory chases will be erased.
(2) Press the # button (1-8) that you want to record to.CHASE
(5) Press the button twice to exit .BLACKOUT
Record Custom Chases
(1) Engage Record mode as described on page 3.
(3) Set your scene with faders to desired setting.RED, GREEN, BLUE & MASTER
(4) Press the button to store the step. Repeat steps 3 & 4
to store up to 20 steps/scenes per chase.
RECORD
-4-

Factory Default Reset
(1) Switch the LED Operators main power OFF.
(2)Press and hold down buttons 1, 6 & 8 then
simultaneously switch the power switch ON then release all
buttons. A
Color Preset
ll LED indicators will flash three times to confirm that
factory settings have been restored.
(3) Press the "STROBE" button again to disengage the strobe effect.
(2) At any time, you can adjust the Strobe flash rate by pressing and
holding down the "Strobe" button then manually adjusting the Speed fader.
SPEED
0.1S
10Min
++
The strobe function will mix with a running Color Preset or Chase. Pressing the Strobe button will temporarily
incorporate a strobe effect over a running color preset or chase.
(1) Press the "STROBE" button when effect is desired.
Strobe Function
WARNING! THIS OPERATION WILL ERASE CURRENT COLOR PRESETS AND CHASES. ALL COLOR
PRESETS AND CHASES WILL BE REPLACED WITH FACTORY COLOR PRESETS AND CHASES.
-5-