American International ACU-K862 User manual

American
International
Car
Stereo
Installation
Kits
&
Accessories
VEHICLE
APPLICATIONS
Acura
1999-2003 TL
2000-2003 CL
©2010 AMERICAN INTERNATIONAL INDUSTRIES, INC.
...
·-
=--::
en
c
·-
...
c
=
c:»
2
N
CD
CD
:Ill
I
=
u
Ill
Ver. 12/10

DASH
DISASSEMBLY
INSTRUCTIONS
1. Starting from the back edges, lift upward and remove both left and right wood trim
side console trim panels. (Opening the Armrest compartment makes this step easier)
2.
With the armrest open, remove the
(2)
Phillips screws from under the bottom of
carpeted padding and remove the
(2)
Phillips screws from the front edge of the rear
console, then pull console section back a few inches.
3.
From the left side of the dash, unclip and remove the fuse box panel cover and
remove the single Phillips screw at the lower edge securing the front lower dash trim.
4.
Carefully unclip the driver's side lower dash panel, disconnect the harness and set
panel out of the way.
5.
Remove the
(4)
Phillips screws securing the drivers side center console side panel
and remove panel.
6.
Remove the
(3)
Phillips screws securing the passenger side center console side
panel and remove panel.
7.
Disconnect the harnesses from each seat heater switch located at the front edge of
the center console.
8.
Carefully unclip the seat heater switch trim and remove the switched from the trim
then remove the seat heater switch trim.
9.
Remove the
(2)
Phillips screws exposed after the heater switch panel has been
removed.
10.
Remove the (2) Phillips screws from the upper back edge securing the forward
section of the center console.
11
. Pull the forward section of the center console back.
12.
Remove the
(3)
Phillips screws from each side of the radio assembly.
13.
Carefully unclip and pull forward the lower edge of the climate control trim panel to
allow the upper edge of the radio assembly to be pulled forward.
14.
Carefully pull radio assembly forward, disconnect all harnesses and antenna lead
and
remove radio.
15.
Remove the individual plastic clip attached to each side of the factory radio and
re-
insert into the ACU-K862 kit
in
the same slot locations provided.
16.
Remove the (2) Phillips screws securing the factory pocket above the radio and set
aside to attach to the upper section of the ACU-K862 kit.
Note:
Attach one of the (2) metal retaining clip (included
in
kit) to each of the upper
storage pocket mounting tabs located
on
the kit (see illustration
on
next page).
Position the factory storage pocket removed
in
step 16 of dash disassembly instructions
onto the top edge of the ACU-K862 kit and secure using the screws supplied with
kit.

DOUBLE ISO/DOUBLE DIN MOUNT INSTRUCTIONS
1. Insert ISO brackets inside the radio opening from the rear of the main mounting kit
(see illustration below).
2. Slide each bracket into the bracket mounting tab slots on the ACU-K862
trim so the mounting holes line up
on top of the trim mounting holes.
3. Slide radio component(s) into kit from rear & attach to ISO mounting brackets
using screws supplied with radio or with mounting kit.
(do not tighten screws at this time).
4. Slide radio component(s) forward or backward for your desired look and then
tighten the mounting screws.
5. Attach rear support strap to support the weight of the new radio component(s)
to the rear of the radio.
@
/
Fig. A
RETAINING
CLIPS CLOSE-UP
/
ACU-K862
ATTACH
RETAINING CLIPS
r2.
~~
IMB862L
~~
I
I
I
I
I
I
I
I
I
I
I
I ...___.......,_....._~
I
I
I
BRACKET SLOTS

For
information
about
other
American
International
automotive
accessories
visit
our
website
at:
http://www.americaninternational.net
American International
Automotive Products Division
1040
Avenida
Acaso
•
Camarillo,
CA
93012,
U.S.A.
USA
Sales
(800)
336-6500
Canada
Sales
(888)
922-3006
•
USA
Fax
(805)
388-7950
CUSTOMER
HELP
LINE
USA
800·323·4329
•
Canada
800·245·8777
IAcuK
862