American Lighting MINI-P2-NF Series User manual

RV1536
www.americanlighting.com PAGE 1 OF 2
Figure 1
Do not operate Polar2 Mini Neon
while it is tightly coiled.
WARNING: These products may represent a possible shock or re hazard if improperly
installed or attached in any way. Products should be installed in accordance with these
instructions, current electrical codes, and/or the current National Electric Code (NEC).
Use this product only with its attached plug-in power cord or those included with the reel. Any
other power cord or feed may damage the xture. Not intended for hard wire use.
WARNINGS: READ ALL INSTRUCTIONS BEFORE YOU START:
CAUTION - To reduce risk of re, electric shock, or injury to persons, pay close
attention to this manual and stay within its guidelines when using this product.
Before use, note that this product requires an 120V AC outlet.
Ensure that the voltage of your power supply is compatible!
POLAR 2 MINI NEON, BULK REELS
Instructions for MINI-P2-NF-SERIES
120V AC, 60Hz
1. Do not cover this product as the covering may cause rope to overheat, melt, or ignite.
2. Do not operate Polar 2 Mini Neon while it is tightly coiled.
3. Do not submerge exible light in liquids, or use the product in the vicinity of standing water or other liquids.
4. Do not route the cord or Polar 2 Mini Neon through walls, ceilings, doors, windows, or any similar part of the building
structure.
5. Secure this exible light using only the mounting clips provided or factory recommended mounting track (sold separately).
6. Do not secure this product or its cord with staples, nails, or like means that may damage the insulation.
7. Do not use if there is any damage to the PVC housing or power cord insulation. Inspect periodically.
8. Do not install on gates or doors, where subject to continuous exing.
9. Do not install in tanks or enclosures of any kinds.
10. Follow instructions carefully when splicing Polar 2 Mini Neon sections or attaching power cords. Ensure that all connections,
including the end cap on the last segment, are properly installed with dielectric grease and shrink tube to preclude the
entrance of water (outdoor applications).
11. Risk of re. Do not replace attachment plug. Discard product if attachment plug is damaged.
12. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock.
This plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does
not t, contact a qualied electrician. Never use with an extension cord unless plug can be fully inserted. Do not alter plug.
13. Polar 2 Mini Neon can only be cut at specic intervals as indicated by the cutting marks printed on the side of the PVC
housing. Failure to cut at a cut mark, will result in a loss of light. Before making any cuts or attaching any power
cords or jumpers, be sure power source is disconnected! Cutting Polar 2 Mini Neon will void the c/ETL/us Listing!
14. This product is designed for use by a qualied installer.
15. This product is for decorative use only. Not to be used by children as a toy. Keep out of reach of small children.
16. Do not exceed 150’maximum run distance in any single run.
CAUTION - To reduce the risk of re, electric shock, or injury to persons:
WARNING: When using outdoor portable lighting products, basic safety precautions should always
be followed to reduce the risk of re, electric shock, and personal injury, including the following:
1. Use dielectric grease and shrink tube at all power connections, including end cap when using outdoors.
2. Use ground fault circuit interrupter (GFCI) protection on the circuit(s) or outlet(s) when using outdoors.
3. Use only UL approved outdoor extension cords, such as type SW, SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW.
This designation is marked on the jacket of the extension cord.
CONNECTING POWER (See Figure 1)
NOTE: Do not exceed 150’maximum run distance in any single run.
1. Secure attached power cord by tightening threaded collar to Polar 2 Mini
Neon. (See Figure 1)
2. Determine the required length for lighting application. If less than 150 feet is
needed, follow the directions on reverse. Note: If cut, the Polar 2 Mini Neon
loses the c/ETL/us Listing.

RV1536
www.americanlighting.com PAGE 2 OF 2
Cutting increments are marked on
the side of the housing as shown
1
0
-
1
0
A
M
E
R
I
C
A
N
L
I
G
H
T
I
N
G
1
2
0
V
,
6
0
H
Z
M
A
X
L
E
N
G
T
H
1
5
0
F
T
.
Figure 2
Line up the barbed ends of the
power pin with the wires inside and
push pin in to make solid contact
Trim off any wires that protrude from the
Polar 2 Mini Neon to prevent a short
Power pin
Polar 2 Mini
Neon
Figure 3
Figure 5
Fuse is inside plug.
Slide open fuse access cover as shown.
Power cord
sheath
Polar 2 Mini
Neon and power
pin assembly
Heat shrink
tube
Figure 4
NOTE: Do not exceed 150’maximum run distance in any single run.
If cut, the Polar 2 Mini Neon loses the c/ETL/us Listing.
1. Determine the required length for exible light.
2. Cut the Polar 2 Mini Neon squarely at the nearest cut mark using a sharp rope
light cutting tool or shears. NOTE: Polar 2 Mini Neon is wired in parallel with
18” cutting increments. Cutting anywhere other than the end/beginning of a
cutting increment will damage an LED and/or internal wiring. (See Figure 2)
3. Holding the smooth pins of the power pin with a pair of pliers, line up the
barbed pins with the two wires of the exible light. Push barbed pins into Polar
2 Mini Neon until ush, being sure to make solid contact with the exible light’s
internal wires. (See Figure 3)
4. Slide the shrink tube over the assembly and onto the Polar 2 Mini Neon.
5. Push the power cord sheath onto the assembly until fully seated.
6. Slide the heat shrink tube over the power cord sheath so that it is centered over
the junction of the Polar 2 Mini Neon and the power cord sheath. (See Figure 4)
POLAR 2 MINI NEON, BULK REELS
Instructions for MINI-P2-NF-SERIES
120V AC, 60Hz
×

×
×
TO REPLACE FUSE (See Figure 5):
This plug contains an electrical fuse as a safety feature.
1. Disconnect power before replacing the fuse.
2. Grasp plug and remove from the receptacle or other
outlet device.
3. Do not unplug by pulling on the cord.
4. Slide open the fuse access cover (See Figure 5)
5. Remove old fuse carefully.
6. Never attempt to replace the fuse with a higher
wattage fuse. Use only 8 Amp 125 Volt fuse. Failure
to do so may be a re hazard. (One spare included.)
7. Set new fuse in holder and close fuse access cover.
7. When using splice kits and/or jumpers, follow steps 1-6 above, making
connections in a similar manner.
8. Attach end cap to other last section of exible light to cover exposed end.
MOUNTING:
1. Make mounting clips using cut pieces of track (MINI-P2-NF-CLIP, sold
separately) or for straight line applications, use MINI-P2-NF-CHAN-3 alu-
minum channel (sold separately).
2. Make sure that the distance between any two parallel runs of lighting are
at least 1/2” apart.
3. Gently press exible light into track or clips so that it snaps into place.
DO NOT TWIST, HANG VERTICALLY, OR SUSPEND
UNSUPPORTED IN THE MIDDLE:
PROP 65 WARNING:
Handling the coated electrical wires of this product exposes you to
lead, a chemical known to the State of California to cause cancer,
birth defects, and other reproductive harm. Wash hands after use.
CUTTING POLAR 2 MINI AND CONNECTING POWER CONNECTION KIT (See Figures 2, 3, and 4)