American Standard Rondo Whirlpool 7242.028W User manual

RONDO™WHIRLPOOL
HIGH GLOSS ACRYLIC
RONDO WHIRLPOOL
❏7242.028W Whirlpool featuring System II
•Acrylic with fiberglass reinforcement
•Pre-leveled tub bottom
•Two person design with center drain and dual
lumbar ends
•Wave style grab bar
•2.0 HP, two speed, self-draining pump/motor
with pulse feature
•Factory installed power cord and plug
•Ten multi-directional and flow-adjustable jets
including:
- Two Ideal-flow jets
- Six body massage jets
- Two recessed back-rest jets
•Deck-mounted electronic control with 20
minute built-in timed safety shut off and
Chrome Bezel
•Three silent air volume controls
•Quick Connect Safe-T-Heater connection
system
•Factory installed and tested whirlpool system
❏7242.028WC StayClean™Whirlpool
Massage featuring System II
•Same as 7242.028W except with the
StayClean™whirlpool system featuring
Antimicrobial AlphaSan®
Nominal Dimensions: 1816 x 1067 x 546mm
(71-1/2”x 42”x 21-1/2")
© 2003 American Standard Inc. BV-10
Rev. 3/03
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
•ASME A112.19.7M for Whirlpool Appliances
•ANSI Z124.1 for Plastic Bathtubs
•ASTM E162 for Flammability
•NFPA 258 for Smoke Density
To Be Specified - Required:
❏Color:
❏Bath Filler: (specify finish)
❏Symphony Drain: 1573.272 (specify color)
or
❏Bath Drain: 1583.470 (specify finish)
To Be Specified - Optional:
❏Safe-T-Heater*: 9075.120
❏Universal Tile Bead Kit: 751755-100
❏Twist Syle Grab Bar: 750565-000 (specify color)
❏System II Control Bezel: 9861.100 (specify finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.

RONDO™WHIRLPOOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES: BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR
PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL
SUPPORT REQUIRED. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX, MAY BE REQUESTED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
FITTINGS AND TWIST GRAB BAR NO. 750565-000 NOT INCLUDED, MUST BE ORDERED
SEPARATELY.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR
INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON
INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF
152mm (6) ABOVE ROUGH FLOOR.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
●
●
■
1816mm
(71-1/2)
546mm
(21-1/2)
ROUGH
FLOOR
495mm
(19-1/2)
908mm
(35-3/4)
165mm
(6-1/2) 76mm
(3)
ON/OFF
SWITCH
PUMP
C/L OF DRAIN
229 X 305mm
(9 X 12)
CUTOUT
1067mm
(42)
267mm
(10-1/2)
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
51mm
(2)
OUTLINE OF
CUTOUT
95mm
(3-3/4)
83mm
(3-1/4)
38mm
(1-1/2)
C/L OF
OVERFLOW
38 mm (1-1/2)
TAILPIECE
LEVELING STRINGER
NOT FOR SUPPORT
●RECOMMENDED FITTING
LOCATION 64 X 279mm
(2-1/2 X 11)
▲
■
INTEGRAL
FEET
SAFE-T-HEATER
REMOVABLE BLANK
GENERAL SPECIFICATIONS FOR 7242 WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM II PUMP
71-1/2 x 42 x 21-1/2 In (1816 x 1067 x 546mm)
94 Lbs.(43 Kg.)
818 Lbs.(371 Kg.)
87 Gal. (330 L)
67 Gal. (254 L)
45 x 25 In. (1143 x 635mm)
60 x 30 In. (1524 x 762mm)
14-7/8 In (378mm)
39 Lbs./Sq.Ft. (191 Kgs./Sq.m)
30.3
58.7
2.1 HP, 15.6 AMPS,120.
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)