American Standard 1340 User manual

Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (1) or 3/8" O.D. BULL-NOSE RISERS (2).
Use adjustable wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply when bending.
Use tubing cutter to cut to proper length.
MAKE WATER SUPPLY CONNECTIONS

Plumbers' Putty or CaulkingAdjustable WrenchChannel Locks
TOOLS REQUIRED

INSTALL FAUCET
1340.225
1340.255
1340.265
Certified to comply with ANSI A112.18.1
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds
smoothly--please read these instructions carefully
before you begin.
Installation
Instructions
METERING
Center Set Faucets
FERRULE
COUPLING NUT
2
3
4
5
11
2
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Insert faucet SHANKS through holes of SINK or
MOUNTING SURFACE.
Install GASKET (2), FRICTION WASHER (3), DEEP
WASHER (4) and LOCK NUT (5). onto SHANKS (6).
Tighten LOCK NUTS (5) firmly to secure FAUCET (1).
Apply a bead of PUTTY along the edge of the
underside of the FAUCET (1).
SINK OR
MOUNTING
SURFACE
PUTTY
SHANK
Turn off hot and cold water supplies before beginning.
CAUTION
1340.225 1340.255 1340.265
2.5mm Hex Wrench
 

PRESS HANDLE
DOWN TO
OPERATE
Turn on water supplies and check connections for leaks.
Remove AERATOR (1) with KEY (2) supplied.
Operate HOT and COLD HANDLES by pressing down on
HANDLES. Both Hot and Cold handles are set for approximately
8 second operating cycles.
Replace AERATOR (1).
Unthread SPOUT NUT (1) and remove SPOUT (2)
Remove SPOUT CLIP (3) and O-RINGS (4).
Replace RUBBER RING (5) with separate
PLASTIC RING (6) supplied with faucet.
Replace SPOUT CLIP (3) and O-RINGS (4).
Reassemble SPOUT (2) TO BODY.
TEST INSTALLED FITTING
!
Remove HANDLE (1) by removing INDEX BUTTON (2)
and SET SCREW (3) with a 2.5mm hex wrench.
Pull off HANDLE (1).
To increase cycle time, turn the gray PLASTIC ADJUSTING
NUT (4) clockwise.
To decrease cycle time, turn the gray PLASTIC
ADJUSTING NUT (4) counter-clockwise.
Replace SET SCREW (3), INDEX BUTTON (2) and
HANDLE (1). Test faucet for proper operation and
cycle time.
TO ADJUST CYCLE TIME
"
CONVERT RIGID SPOUT TO SWIVEL SPOUT
(1340.255; 1340.265)
$
SERVICE
#
1
2
WATER SUPPLIES
1
23
1
4
3
5
6
2
4
TO INCREASE CYCLE TIME
ROTATE CLOCKWISE
REMOVE
RUBBER RING
INSTALL
PLASTIC RING
TO DECREASE CYCLE TIME
ROTATE COUNTER-CLOCKWISE
2.5mm HEX WRENCH
M968493
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH,
ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
Remove HANDLE (1). Refer to Step 4 for handle removal.
Remove ACTUATOR ASSEMBLY (2).
Remove WASHER (3). Pull out VALVE ASSEMBLY (4) and
FILTER SCREEN (5).
Inspect that VALVE ASSEMBLY (4), FILTER SCREEN (5) and
VALVE SEAT (6) are clean and free from debris. VALVE
ASSEMBLY (3) and FILTER SCREEN (5) can be cleaned with
soap and water.
Replace FILTER SCREEN (5) and VALVE ASSEMBLY (4). Place
WASHER (3) on top of VALVE ASSEMBLY (4). Thread VALVE
ACTUATOR (2) onto faucet. Torque VALVE ACTUATOR (2)
to 12-15 ft. lbs (15-20 Nm).
Replace HANDLE (1).
1
4
3
5
2
REMOVE REPLACE

METERING
Center Set Faucets
CHROME 002
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2005
M962397-0070A
MOUNTING KIT
024220-0070A
SUPPLY NUT
M962396-YYY0A
6" SPOUT KIT
M962395-YYY0A
5" SPOUT KIT
M962394-YYY0A
AERATOR
1340.225
5" GN 1340.255
6" GN 1340.265
012087-0070A
SPOUT SEAL KIT 051214-0070A
SWIVEL & FIXED
SPOUT RINGS
M968493
PRODUCT NUMBERS
M962390-YYYOA
HANDEL KIT
M962391-0070A
INDEX KIT
M952200-YYY0A
ACTUATOR UNIT
M913860-0070A
WASHER
M952210-0070A
VALVE
M952220-0070A
FILTER SCREEN
M962392-0070A
VALVE KIT
M962393-YYY0A
1.56 GPM AERATOR
M962394-YYY0A
AERATOR