American Standard CenterSet 2471 User manual

by
COLLECTION
™
THE
Connect water supply to FAUCET (1) with 1/2" IPS F EXIB E
SUPP IES (3) or 3/8" O.D. BU -NOSE RISERS (4). Use
adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
Secure FAUCET (1) with ATTACHMENT NUTS (2) supplied.
(HAND TIGHTEN).
SECURE FAUCET AND MAKE WATER
SUPPLY CONNECTIONS
Plumbers' Putty or CaulkingAdjustable WrenchChannel ocks
TOOLS REQUIRED
12
M968286
INSTALL FAUCET
2471
Certified to comply with ASME A112.18.1M
Certifié ASME A112.18.1M
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read
these instructions carefully before you begin.
Installation
Instructions
CenterSet Faucet
2
FERRU E
COUP ING NUT
(HAND TIGHTEN)
2
1
4
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Insert faucet SHANKS through holes of SINK. Place
faucet as far forward as possible.
Apply a bead of PUTTY along the edge of the
underside of the BODY (1). Insert IFT ROD (2)
through hole in BODY (1).
SINK
1
PUTTY
SHANK
Turn off hot and cold water supplies before beginning.
CAUTION
Basin Wrench Tubing Cutter

M968286
INSTALL POP-UP DRAIN
31
2
A
4
5
10
11
12
8
G
D
E
6
7
F
C
9
Push Tail piece (11) down into Trap (C) (threaded end up).
Assemble Pivot Rod (9) as shown in Figure-4B. Notice the
position of the Concave Washer (G).
Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot
Nut (F).
Thread ocknut (5), Washer (4) and Gasket (3) (Bevel side
up) onto Drain Body (10).
Apply a bead of Putty (D) to underside of Flange (2).
Remove one end of Clip (8) from Pivot Rod (9) by squeezing
ends together while sliding.
Insert Pivot Rod (9) into second or third hole in Extension
Rod (7) and reassemble Clip (8).
Adjust stopper height by repositioning Extension Rod (7) and
tightening Thumbscrew (6).
Feed Drain Body (10) up through Sink (A) and thread the
Flange (2) fully onto Drain Body (10).
Tighten ocknut (5) firmly, keeping the pivot rod hole pointed
towards the back of the sink.
Drop Stopper (1) into Drain Body (10).
Position Extension Rod (7) onto Pop-Up Rod (E) and tighten
Thumbscrew (6). 1-1/4"
FIGURE-4B:
Push TAI PIECE INSERT (12) into TAI PIECE (11) and push
TAI PIECE up and thread tightly into DRAIN BODY (10).
F
5CHECK DRAIN CONNECTIONS
1
2
Operate Pop-Up and fill lavatory with water. Check that
DRAIN STOPPER (1) makes a good seal and retains
water in lavatory. Adjust stopper height by repositioning
Pop-Up Rod (2) and tightening Thumbscrew (3).
Release DRAIN STOPPER (1) and check all drain
connections and "P" trap for leaks. Tighten if necessary.
"O" RING
4TEST INSTALLED FITTING
With HAND ES (1) in OFF position, turn on WATER
SUPP IES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate both HAND ES to flush
water lines thoroughly.
Replace AERATOR (3).
1
1
2
6
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.

M968286
MODEL NUMBER
99405 -0070A
VA VE
024220-0070A
SUPP Y NUT
065800-0070A
ATTACHMENT NUT
A918572-0070A
HAND E SCREW
M962164-0070A
POP-UP ROD
M96224 -YYYOA
EVER HAND E
M918049-0070A
ADAPTER
66070-YYY0A
AERATOR
CenterSet Faucet
CHROME 002
SATIN 295
Replace the "YYY" with
appropriate finish code
072574-0070A
EXTENSION ROD
066116-YYY0A
DRAIN STOPPER
GASKET
WASHER
OCKNUT
M961711-0070A
TAI PIECE INSERT
F ANGE
070847-0070A
C IP
066118-0070A
PIVOT ROD
95 450-YYY0A
COMP ETE
DRAIN ASSEMB Y
0705 2-0040A
TAI PIECE
066117-YYY0A
F ANGE KIT
M961162-0070A
INDEX BUTTON (HOT)
M96116 -0070A
INDEX BUTTON (CO D) 2471
by
COLLECTION
™
THE
HOT INE FOR HE P
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003