American Standard Standard Console Table 7483.002 Instruction manual

730520-100 Rev. D
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
ASSEMBLY & INSTALLATION
INSTRUCTIONS
7483.002
7483.295
CONSOLE TABLE
- 1 -
byCOLLECTION
®
“”
THE
Recommended Tools & Materials Roughing-in Dimensions
Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
Adjustable Wrench
Channel Locks
Regular Screwdriver
Phillips Screwdriver
10'
Pipe Wrench
Putty Knife
Drill
Saber Saw
Level
Basin Wrench
Plumbers' Putty or
Caulking
Tubing Cutter
Tape
Measure
Hacksaw
32
(813mm)
26-5/8
(676mm)
FINISHED WALL
FINISHED WALL
17
(432mm)
8-1/2
(216mm)
9-1/2
(241mm)
0283.000 STANDARD® CONSOLE PEDESTAL TOP
8710.000.002 CONSOLE TABLE LEGS (Chrome)
8710.000.095 CONSOLE TABLE LEGS (Satin)
20
(508mm)
36
(914mm)
10-1/4
(260mm)
FINISHED
FLOOR
3-7/8
(98mm)
3/4
(19mm)
13
(330mm)
24
(610mm)
22
(559mm)
SUPPLIES
1-1/4 O.D.
WASTE
1-1/4 O.D.
TAILPIECE
8
(203mm)
®

730520-100 Rev. D
- 2 -
1A 1B
1
3
2
Slide Shelf Support (item #1) onto 4 leg
subassemblies.
Slide the 4 Upper Legs (item #4) onto the
Threaded Rods from the 4 leg subassemblies
as shown.
Remove lower leg
support / adjustable
foot assembly
(items 2 & 3) from
accessories box
and screw them
completely onto the
4 threaded rods
(item 5).
Unscrew the 2 front
leg trumpets (item
6) and 2 rear leg
trumpets (item 7)
from the threaded
rod (item 5).
Slide the 2 Towel Bar Assemblies (item #9) over the tops of the Trumpets
and secure with the 4 Towel Bar Retaining Nuts (item #10). The retaining
nuts can be tightened by hand.
Place the 2 Front Leg Grommets (item #12) over the tops of the 2 Front
Leg Trumpets.
NOTE: To prevent breakage, slide the Oval Glass Shelf (item #11) into
place
only after the lavatory and Console Legs are completely
assembled and the lavatory is bolted to the wall.
Be sure to remove
protective film from glass shelf before final assembly.
CAUTION: Do not use towel bars as handles to move the console table.
Lift the console from the upper legs.
After console table is assembled, follow lavatory installation
procedure below.
Screw on the 2 Front Leg Trumpets
(item #6) and 2 Rear Leg Trumpets
(item #7). Make sure the Upper
Legs recess into the underside of
the Trumpets.
Provide suitable reinforcement behind finished wall for
lavatory hanger mounting screws. The desired rim height
for the Standard pedestal top is 36". The centerline for the
hanger positioning slots should be located at
30-3/4". (Make sure support bottom
extends to pedestal top back wall bottom.)
Hanger
Location
C/L of 2 x 8
Support
and Bracket
Finished
Floor
NOTE: If replacing an existing lavatory be certain to shut off
water supply before removing old lavatory.
30-3/4"
4
Threaded
Rod
Threaded
Rod
1
7
Rear
6
Front
12 10
9
6, 7
5
Front
PEDESTAL TOP AND CONSOLE TABLE LEG INSTALLATION
2
3

2
3
730520-100 Rev. D
- 3 -
30-3/4"
36"
HOLES FOR
ANCHOR
SCREWS
IN BACK
DRAPERY
SUPPLIES AS
REQUIRED
WASTE
FINISHED FLOOR
HANGER *C/L OF
HANGER
ANCHORING
SLOTS
Steel
Hanger
Mounting
Screw
Hanger
Positioning
Screw
Anchor Screw
in Lavatory
Feet are
adjustable
Lavatory
Front Leg
Grommet
of Console
Table
Position hanger according to Step 1, making sure its center is aligned with the waste hole centerline (Fig. 1). Mark
the hanger screw locations through its mounting holes. Drill pilot holes in positioning screw slots of hanger (Fig. 2).
MOUNTING SCREW
HOLES (4)
POSITIONING
SCREW SLOTS (2)
Following manufacturer's instructions, install faucet and drain assembly.
(Not included). Be certain to apply a bead of sealing putty on the underside
of the drain in order to ensure a watertight seal between the
lavatory and drain. Remove excess putty after installing drain on lavatory.
BC
4
4
5Connect the trap to drain assembly hand tight to check alignment. It may be
necessary to cut off part of the tailpiece (area "B") or part of the horizontal leg
of the trap (area "C").
Secure lavatory on hanger as shown in Step 3. Insert and tighten anchor
screws. Connect hot and cold supply lines to the shut-off valves. Tighten trap
joints for watertight assembly. Apply a bead of caulk around the edge which
contacts the wall as shown. Insert the oval glass shelf onto the shelf support of
the console table legs.
Fig. 1 Fig. 2
We recommend using two people for installation.
1. Affix hanger to wall (hand tighten only).
2. Move console table legs into approximate position against
the wall.
3. Mount lavatory on bracket making sure the front leg
grommets of console recess into the holes on the underside
of the lavatory.
4. Mark the bottom anchor screw holes in the lavatory.
5. With a pencil, mark the floor around each foot of the console
table.
6. Remove the lavatory and the console table legs.
7. Tighten the hanger positioning screws and drill pilot holes for
bracket mounting screws and lavatory anchor screws. Install
and tighten the bracket mounting screws.
8. Use 1/4" drill bit and drill holes marked on finished floor at
least 1/8" deep.
Move console table legs in place and position the feet in the holes
previously drilled in the floor in Step 3. Return the fitted lavatory to the
installed position. Level the lavatory by using the adjustable feet and the
rear leg adjustment bumper on the console table legs.
C/L
Rear Leg
Adjustment
Bumper

730520-100 Rev. D
- 4 -
8
1210
9
7
6
4
5
1
11
2
3
13
CARE INSTRUCTIONS: Rinse the product clean with clear water. Dry with a soft cotton flannel cloth.
DO NOT: Clean with soaps, acid, polish, abrasives, harsh cleaners, or a cloth with coarse surface.
AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard
will repair or, at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building
or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other
damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American
Standard.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American
Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of
which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to
you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not
affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request
(including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty information may also be
obtained by calling the following toll free number: [phone]
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
ITEM # PART NO. PACKED QTY. DESCRIPTION
1 738632-XXX0A 1 Shelf Support
2 738630-XXX0A 4 Lower Leg Support
3 738628-XXX0A 4 Adjustable Foot Assembly
4 738625-XXX0A 4 Upper Leg
5 738629-0070A 4 Threaded Rod
6 738624-XXX0A 2 Front Leg Trumpet
7 738623-XXX0A 2 Rear Leg Trumpet
8 738622-0070A 2 Rear Leg Adjustment Bumper
9 738621-XXX0A 1 Towel Bar Assembly
10 738614-XXX0A 4 Towel Bar Retaining Nut
11 738612-0070A 1 Oval Glass Shelf
12
13 738613-0070A 2 Front Leg Grommet
738619-0200A
382430-1120A 2 Ceramic Towel Bar Knobs Steel Hanger Bracket
1
738615-XXX0A * Elbow Brackets
738620-XXX0A * Towel Bar
* These components are part of the Towel Bar Assembly (Item #9).
NOTE: Items 2, 3, and 5 (Lower Leg Support, Foot Assembly, and Thread Rod) are
packaged preassembled.
For chrome, replace "XXX" with 002 when ordering.
For satin, replace "XXX" with 295 when ordering.
8710 CONSOLE TABLE LEGS COMPONENTS LIST
Note: "XXX" represents color or trim finish options. Specify when ordering.
www.AmericanStandard-US.com www.AmericanStandard.ca www.AmericanStandard.com.mx