American Standard 0660 LOFT User manual

Recommended Tools
& Materials Phillips Screwdriver
Basin Wrench
Putty Knife
Drill
Hacksaw
Pipe Wrench
Channel Lock Pliers
Adjustable Wrench
1A 2
3
Drill a clearance hole inside the
perimeter line of the template.
Cut opening around the
perimeter of the template.
Perimeter
of template
Perimeter
of template
730687-100
Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for years. To
help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also,
review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
1B
Using the template provided, locate the position of the sink. Provide proper
clearance under the countertop for the fauce t supply lines, drain assembly and
the structural parts of the cabinet.
NOTE: If replacing an existing sink be certain to shut off water supply before
removing old sink.
Mount the faucet and drain
assembly (not included) on
the sink following the
manufacturer's instructions.
Be certain to apply a bead
of sealing putty on the
underside of the drain (Part
"A") in order to ensure a
watertight seal between the
sink and drain. Remove
excess putty after installing
drain on sink.
OBSERVE LOCAL PLUMBING AND BUILDING CODES
FOR USE WITH: 0660 LOFT
0670 MORNING
0680 PETAL
Installation
Instructions
™
NOTE: For Wallmount or
Countertop faucets, drill faucet
holes according to
manufacturer's instructions.
A
Using the template as a guide, locate the
faucet hole on the countertop. Allow 1"
minimum clearance between:
• the sink and faucet spout
• the sink and end of faucet handles
• the backsplash and faucet spout and handles
Use the faucet installation instructions for
required clearances.
Countertop faucet installations:
Insure sufficient spout overhang into
the sink. See manufacturer's
installation instructions and roughing-
in notes for minimum spout lengths.
Wall-mount faucet installations:
OUTSIDE
EDGE OF
SINK
CUT-OUT
LINE
1" (25mm)
MIN.
BACKSPLASH
A
ABOVE COUNTER SINK
Tubing Cutter
Regular Screwdriver
Plumbers' Putty or Caulking
Tape Measure
© American Standard Inc. 2004

Saniwares
7
BC
730687-1002
Connect trap to drain
assembly hand tight to check
alignment. It may be
necessary to cut off part of
the tailpiece (area "B") or
part of the horizontal leg of
the
trap (area "C"). Secure joints
for watertight assembly.
4
5
6
Before applying the sealant, place the sink temporarily into the cut-
out. Check for alignment and clearance. Then mark the sink
and
countertop in several places as a guide for the installation location.
After checking fit and
alignment, turn sink
upside down and apply a
generous portion of
sealant around the
under side of the rim
near the edge.
Connect supply line to faucet (finger tight) and carefully bend tubes to
engage with the supply shut-off valves. Tighten connections at faucet
and shut-off valves for secure seal.
Shut-Off Valves
In the United States:
American Standard Inc.,
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States,
warranty information may also be
obtained by calling the following
toll free number: [phone]
In Canada:
American-Standard,
2480 Stanfield Rd.,
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
If inspection of this American Standard plumbing
product, within one year after its initial installation,
confirms that it is defective in materials or workmanship,
American Standard will repair or, at its option, exchange
the product for a similar model.
This limited warranty does not apply to local
building code compliance; since local building codes
vary considerably, the purchaser of this product should
check with a local building or plumbing contractor to
insure local code compliance before installation.
This warranty shall be void if the product has
been moved from its initial place of installation; if it has
been subjected to faulty maintenance, abuse, misuse,
accident or other damage; if it was not installed in
accordance with American Standard's instructions; or if it
has been modified in a manner inconsistent with the
product as shipped by American Standard.
American Standard's option to repair or exchange
the product under this warranty does not cover any labor
or other costs of removal or installation, nor shall
American Standard be responsible for any other
incidental or consequential damages attributable to
a product defect or to the repair or exchange of a
defective product, all of which are expressly
excluded from this warranty. (Some states or
provinces do not allow the exclusion or limitation of
implied warranties, so this exclusion may not apply to
you.) This warranty gives you specific legal rights. You
may have other statutory rights that vary from state to
state or from province to province, in which case this
warranty does not affect such statutory rights.
For service under this warranty, it is suggested
that a claim be made through the contractor or dealer
from or through whom the product was purchased, or
that a service request (including a description of the
product model and of the defect) be sent to the following
address:
AMERICAN STANDARD
ONE-YEAR LIMITED WARRANTY
Shut-Off Valves